I have a hd2 with blutopia n supersports rom and today has been 1 helluva messed up day seriously !( I cant think straight) its all because my phone wont work. the phone was working beautifully with android on it and out of nowhere today the screen is not responding AT ALL. its so frustrating cant make a call cant read my txts.can some 1 please just tell me what i have to do so i can get a replacement? I put hspl3 and bluetopia android and supersports rom....please tell me what rom do i need to flash to it,do i have to relock/remove hspl3? thanks if u can help me out i just cant think clearly right now
turn off phone, hold down on the up and down volume button by pressing in middle while u toutch the end key..the red key.. after it boots press volum up to redo phone... if that does not fix it.. reflash with original rom
carl1961 said:
turn off phone, hold down on the up and down volume button by pressing in middle while u toutch the end key..the red key.. after it boots press volum up to redo phone... if that does not fix it.. reflash with original rom
Click to expand...
Click to collapse
what about hspl3???? what do i have to do so i can send it back without tmobile asking me why is there a custom rom and hspl3 on ur phone
ihateu said:
what about hspl3????
Click to expand...
Click to collapse
will be replaced when you flash original rom
djcedric said:
will be replaced when you flash original rom
Click to expand...
Click to collapse
ok how can i get the original rom... i cant get it from tmobile website because it wants a mei # and i cant get to it on my phone cause the screen is not working
open your phone up. take the battery off. The IMEI should be there along with serial number. Good luck
Touchscreen problem
Yesterday I start with a similar problem.
Using several Android builds on the same stock memory card.
The touchscreen stops responding always when I try to
reboot or turn off the phone, the same on all Android builds
and on WinMO. But locking the phone brings the touchscreen
back to life. Then I am able to unlock the phone and the
touchscreen keeps working OK.
Will try flashing the updated stock ROM.
you run hspl3 again , but select the other option with the extra.oooo, 208.000 , by default hspl3 installs the one to allow roms to work,,, when you rerun hspl3 select the other to set back to original so you can send back to factory anfter u install the t-mobile original rom
best to read this
http://forum.xda-developers.com/showthread.php?t=653614
Related
I had a problem with the power button not working and I was adviced to reflash the original ROM (I never did a ROM upgrade) so I picked the original and latest Cingular ROM. Flashing strated and then hung for a while @ 80% progress, few minutes after continued up to 95% progress and at that point I got ERROR 326 message (INVALID COMMAND) stating that the NBF file couldn´t be used for this phone. I dissconnected the phone and did a soft reset and what I got was the BOOTLOAD SCREEN and since then I can not make the phone exit from it. Later I tried flashing RUU_RIsidoro_2.26.10.2_WWE+CF2SP1_G4, this time it went all the way to 100% progress and the congratulations screen, I made a soft reset (the only way I know to exit the bootload mode) and I got momentarly the HTC innovation screen and right away dissapeared to enter in bootload screen again.
Then I reflash ROM with RUU_Qtek_9100_AKU2_21878_024711_ESN_G4, this time it went all the way up to 100% and success screen appeared, the phone rebooted and is up and running although with inoperant power button.
Since you've successfully reflashed your phone and the power button isn't still working have you considered a hardware fault?
Look for some info/pics on how to disassemble your wizard to verify if the button is well soldered to the board
luiggi said:
what I got was the BOOTLOAD SCREEN and since then I can not make the phone exit from it. Later I tried flashing RUU_RIsidoro_2.26.10.2_WWE+CF2SP1_G4,
Click to expand...
Click to collapse
Luiggi, pls tell me how to flash the phone while in the bootloader screen?!?
There's no secret to flash while in bootloader screen. Use the RUU file. It might take a little while longer to detect the phone but goes all the way to the end
Yes, it has to be a hardware issue
mestrini said:
Since you've successfully reflashed your phone and the power button isn't still working have you considered a hardware fault?
Look for some info/pics on how to disassemble your wizard to verify if the button is well soldered to the board
Click to expand...
Click to collapse
I´ll try the disassembly and perhaps is not a big deal to fix it, I got a copy of the service manual posted in some of the forums, and I´ll give it a try.
Thanks for the advice!
You just do it!
vlada said:
Luiggi, pls tell me how to flash the phone while in the bootloader screen?!?
Click to expand...
Click to collapse
Try first a soft reset while in the BL screen, if doesn´t react then do what I did:
I just plugged the USB cable and run the RUU!! As simple as that and as risky as the ROM you select not being the right one.
Hi, I was trying to flash my ROM with SSPL and a cooked ROM and now my HD2 is bricked. When I turn it on, the white HTC screen comes up and nothing more happens (except the back gets warm). I'm assuming that the little "void" thing below the battery area means that any warranty is void or something.
Can anyone help? Nothing I can do to it will make anything happen. Thanks all!
SSPL? Aren't you supposed to use the HSPL?
jamesmbaldwin said:
Hi, I was trying to flash my ROM with SSPL and a cooked ROM and now my HD2 is bricked. When I turn it on, the white HTC screen comes up and nothing more happens (except the back gets warm). I'm assuming that the little "void" thing below the battery area means that any warranty is void or something.
Can anyone help? Nothing I can do to it will make anything happen. Thanks all!
Click to expand...
Click to collapse
As far as I know the "void" thing below the battery is correctly in place. If it was missing - then your warranty would be void.
I would put your phone into bootloader and flash a stock rom.
If you have a european phone check this http://forum.xda-developers.com/showthread.php?t=609477
If you have USA phone check here http://forum.xda-developers.com/showthread.php?t=653614
Your phone is not bricked, you should be able to reflash back to a stock rom. To flash a custom rom you should use Hard-SPL, if you do this make sure you pay close attention to the directions, because a long time ago I bricked my wizard because I didn't pay attention to details
http://forum.xda-developers.com/showthread.php?t=606713
And if you have T-Mobile USA 1024 version:
http://forum.xda-developers.com/showthread.php?p=6004691
Fixed my Aussie T9193
Hi, thanks all for the responses, I've gotten it working! I didn't know about getting the phone into bootloader mode FIRST, then doing the installations. BIG help, thanks to the collective wisdom!!
JMB
i flashed one rom,,no prob,,when i tried to flash the "ozrom"...it wont even power up..or charge,,,,im screwed
lennox03 said:
i flashed one rom,,no prob,,when i tried to flash the "ozrom"...it wont even power up..or charge,,,,im screwed
Click to expand...
Click to collapse
post in the ozrom thread then
lennox03 said:
i flashed one rom,,no prob,,when i tried to flash the "ozrom"...it wont even power up..or charge,,,,im screwed
Click to expand...
Click to collapse
did you check your radio and did you use hspl ?
djchubbs said:
post in the ozrom thread then
Click to expand...
Click to collapse
Wrong radio!
I bricked my phone after using "Task 29"... PLEASE HELP!
I just used "Task 29", my phone is stuck on the home screen and will not do anything else. I keep holding down the volume buttons and inserting a USB cord to see if it will sync to my computer so I can upload another ROM, but as soon as the multi colored screen comes up, it quickly changes to a white screen telling me to either press the vol button up for a reset or another key to escape it. If I press up it goes right back to the boot up screen and does the same if I press any other button. Is there anyone who could help me.... PLEASEEEE!!!!
starr073199 said:
I just used "Task 29", my phone is stuck on the home screen and will not do anything else. I keep holding down the volume buttons and inserting a USB cord to see if it will sync to my computer so I can upload another ROM, but as soon as the multi colored screen comes up, it quickly changes to a white screen telling me to either press the vol button up for a reset or another key to escape it. If I press up it goes right back to the boot up screen and does the same if I press any other button. Is there anyone who could help me.... PLEASEEEE!!!!
Click to expand...
Click to collapse
Just hold the volume down button and then press the end call button instead of both the volume buttons...
garavd said:
just hold the volume down button and then press the end call button instead of both the volume buttons...
Click to expand...
Click to collapse
omg!!! I love you!!!!! Thanks sooooo much!!!!
possibly bricked hd2? any help!!??
i just flashed a radio last night. the flashed finished completely. the phone looked like it was going to restart but never came back on. and wont turn on no matter what i do. did i brick my phone? i did have hspl
us hd2 with tmobile
the radio was 2.05.50.11
any help would be helpfull
articulatekevin said:
i just flashed a radio last night. the flashed finished completely. the phone looked like it was going to restart but never came back on. and wont turn on no matter what i do. did i brick my phone? i did have hspl
us hd2 with tmobile
the radio was 2.05.50.11
any help would be helpfull
Click to expand...
Click to collapse
try turning on holding volume down push power and then plug to pc wait for usb to appear on phone screen and do task29 and than reflash your favorite rom again..... good luck!!!!!!!
First of all sorry for my english not good.
Start : with my HD2 have brick after task29 and not success to flash new ROM I'm take USB. cable out and try to open my HD2 in to boot loader by put volum down + power bottom but screen not show any image or 3 color my phone it only long vibration pull battery out waiting 30 minute and put battery in and try to open my phone to boot loader but is same only long vibration.
Now : can not do any think with it when try to plug power in my phone is auto startup and long vibration.
I'm search on google and in this forum not have some one face problem same as me please help me to fix this.
Any body please help me, I'm love it because now we can run both WM. and Android
Upppp waiting for your help
Did you try a long press of the reset-button?
You could try to put the original Stock Image from HTC onto the root-folder of your SD-Card, rename it to LEOIMG.nbh and Push Vol up + Vol down during start and follow the on-screen instructions if it works.
Otherwise use Search-Function in the forum.
ı have jtag HTC for samsung and HTC devices if u want send for repair to me..
www.sevgigsm.net/forum
admin..
I use ORT
Did you check to make sure your radio version was correct before flashing? This is probably the number one reason for bricking.
Check this thread it may help you if you did the flash properly:
http://forum.xda-developers.com/showthread.php?t=668347
i got same problem now...
no screen, no boot, vol down+ power oso same
no screen just a long vibration
anybody help?
I am using the correct radio so don't tell me I am using a wrong radio or something, I have been flashing for 4 months so I know EXACTLY how to flash.
now i can neither get into tri-color or hard reset so don't tell me to flash or smth like that, just tell me how to recover properly
Don't tell us to use search or something because seems like only 2 of us is encountering this problem in the internet
I'm exactly the same problem as TS coz it juz auto go vibrate when plug in battery
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
at the long vibrate, when i plug in to my pc, it will keep on got usb connected and disconnected sound
and dont know what device is connected as not shown in found new hardware and device manager
I also have been searching all possible keywords about what me and TS encountered but all linked to completely UNRELATED results(like search for long vibrations only link to people asking how to make vibration long and 1st result is this thread)
bountygiver said:
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
Click to expand...
Click to collapse
Silly question, but are you holding (and keep on holding) the Volume-Down button while you press the power button?
of course YES
i told you i have been flashing for so long
Leo from T-Mobile. Hi! I've got same problem. After flashing new (next) rom phone definetely died. Phohe is currently simfree and with HSPL. Only one reaction is short vibration after press power button. I searched everywhere. My phone has no bootloader but system see him as Qualcom CDMA Technologies MSM. Thats all, any ideas? Please and thanks for advice.
czaruch said:
Thats all, any ideas?
Click to expand...
Click to collapse
Yes, you flashed a non tmous stock rom that included a ..51.. radio and it destroyed your phone.
What rom? exact filename please.
thank you so much.
I bricked a Leo with the .51 radio. I think I read that is a European or otherwise foreign radio. Since your ROM has Euro in the name.......
czaruch said:
ROM_Leo_HTC_WWE_EastEurope_1-66.
Click to expand...
Click to collapse
The full filename for that rom is
RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Si gned_15.32.50.07U_2.07.51.22_2_Ship.exe
it comes with a version x.xx.51.x radio, and they do Not work on tmous (t mobile us) phones. They kill them
Your phone is dead, sorry. No known fix.
warranty or repair (or JTAG if you are brave and have the money)
a friend of mine bricked his phone. he then tried to microwave it, but that didn't work after that he took a power wire from an old computer, cut it and connected it directly to the phone's parts where the battery would go...this completely f-ed his phone up (he also used a lighter to fake a powersurge of the battery). Then he called htc and a few weeks later he got a new hd2!
GOOD LUCK
lol, he doesnt need to do any of that, its allready as dead as it can be. Loads of epople have had them replaced under warranty with this kind of brick. It wont start, so htc/tmo cant see that its been hacked.
Hi! I understand and realy sad. Somebody know where could I fix it in UK? And how much for this pleasure. Thanks.
i would contact htc, see what they have to say. (dont say you flashed it, it just stopped working")
Hi,
I was running android from my sd card but now wanted to go the NAND way. I installed HardSPL3 to 2.08 and then flashed MAGDLR to the phone. Everything was fine up to here.
Now the problem bit ....... The call button on my HD2 is depressed(I must have sat on it at some point), however it still worked. When I get to the option screen in MAGDLR and go down to 'flash from usb', the call button does not work, so I can navigate up and down but can't select anything!
I'm stuck in MAGDLR ......... Please help!
......one last thing, if I were to have the fault repaired what am I looking at cost wise.
Any help greatly appreciated
Shab
s_hab said:
The call button on my HD2 is depressed
Click to expand...
Click to collapse
Tell it to stop been a wuss and cheer up
Boom Boom ..... i was looking for help, not your one liners. LOL!
Try removing MAGDLR by flashing your official rom from SDcard. This should remove MAGDLR and get you back to WM.
s_hab said:
Hi,
I was running android from my sd card but now wanted to go the NAND way. I installed HardSPL3 to 2.08 and then flashed MAGDLR to the phone. Everything was fine up to here.
Now the problem bit ....... The call button on my HD2 is depressed(I must have sat on it at some point), however it still worked. When I get to the option screen in MAGDLR and go down to 'flash from usb', the call button does not work, so I can navigate up and down but can't select anything!
I'm stuck in MAGDLR ......... Please help!
......one last thing, if I were to have the fault repaired what am I looking at cost wise.
Any help greatly appreciated
Shab
Click to expand...
Click to collapse
Thanks 10507, it all seems clear now ........ why didn't I think of that. It's loading the ROM as I type.
.....Once again thanks dude!
s_hab said:
Thanks 10507, it all seems clear now ........ why didn't I think of that. It's loading the ROM as I type.
.....Once again thanks dude!
Click to expand...
Click to collapse
Glad, I can help
I did flash a stock ROM from my SD card and everything goes fine untill I reboot the phone. Then the MAGDLR screen shows up again. How can I get rid of MAGDLR now because I need to send my phone back to HTC so they can repair the touchscreen which isn't working.
My HD2 call button and windows button unresponsiveness
Hi all guys, i really need a help..since i've upgrading my rom to 3.15, then my hd2 call button and windows button cant be use..i wanna change my windows mobile to NAND..but, im stuck in MAGDLR..so my friends help me to retrive me WM back..any of u know how to overcome my button back?..it is cause by the rom or hardware damage?..im still beginner in this, kindly hoping for all ur opinion guys..
hd2beginner said:
Hi all guys, i really need a help..since i've upgrading my rom to 3.15, then my hd2 call button and windows button cant be use..i wanna change my windows mobile to NAND..but, im stuck in MAGDLR..so my friends help me to retrive me WM back..any of u know how to overcome my button back?..it is cause by the rom or hardware damage?..im still beginner in this, kindly hoping for all ur opinion guys..
Click to expand...
Click to collapse
If you download and flash the official ROM for your HD2 you can flash it via bootloader. While your phone is off press and hold down the volume down button. Connect your phone via USB cable and wait until you see USB in the white bar of tbe bootloader screen and your computer to show it recognizes ths phone. Right click the ROM package and click run az adminostrator. The ROM should flash and remove MAGLDR, bit it has to be an official ROM as a custom will not remove MAGLDR. After flashing is done put phone back into bootloder to check SPL version. You want the SPL of the ROM you flashed. If it is not righr download HSPL 4 and use it to set the correct SPL, hint you want the SPL x.xx.0000 not SPL x.xx HSPL.
If you want to just to make sure flash the official ROM via SD card and it should remove MAGLDR, CWM, and HSPL if house have them. Go here to learn how to do this.
what happens if your down volume button doesnt work. is there any way to flash back to your old rom using magdlr? my call button still works but every time i put it on usb flash and try to install the original rom it doesnt seem to work
Pls Sir Help Its Urzent ???
My Htc HD2 . I try To Change WM to Android . But When I try to select USB FLASHER MODE On MAGLDR . My Call button Not Working (I Never Try To Using Call Button Before) .... Now What Can I DO ?????
Pls Anyone Help Me ?????
so im new to this whole rom thing and i tried installing megatron rom form sdcard with rom manger and when i started it the phone reset and got stuck on LG screen. I tried hard reset and removing the battery. Not working. Do i have a bricked phone now, please say no. HELP ME please
deathmill3001 said:
so im new to this whole rom thing and i tried installing megatron rom form sdcard with rom manger and when i started it the phone reset and got stuck on LG screen. I tried hard reset and removing the battery. Not working. Do i have a bricked phone now, please say no. HELP ME please
Click to expand...
Click to collapse
I'm hoping that you made a backup before you flashed the rom. If you did you should be able to boot into recovery and restore.
lol i think thats what i did. I backup everything using Titanium and rom manger on my sdcard. i just dont know how boot into recovery and restore. thanks for the reply
yep bricked...
All you can do now i's try to flash stock rom with kdz..
and how do u do that lol
deathmill3001 said:
and how do u do that lol
Click to expand...
Click to collapse
Here's the stock rom: csmg.lgmobile.com:9002/swdata/WEBSW/LGP509BK/ATMOBK/V10l_00/V10L_00.kdz
and you'll need KDZ(run it in compatibility mode if using win7 64bit):
http://www.megaupload.com/?d=B99JDF9I
boot phone into emergency mode: Home+Volume Up+Power
connect to PC via USB and flash with KDZ in 3qct +Emergency mode
i cant put my phone in emergency mode
deathmill3001 said:
i cant put my phone in emergency mode
Click to expand...
Click to collapse
my mistake. it is actually Back Button+Up Volume+Power
still nothing :[
Use it as a vibrator from now on, if u can. Haha j/k.
Go for warranty and see what happens..
lol hmmm i wonder what males can do with that.....
i was thinking about doing that and see if i could pull a fast one on radioshack
You did a nand backup before flashing Megatron, right? If so, you should boot in recovery using Home + Vol Down + Power and restore it from there. If not, you have no alternative but flashing the rom again (or any other rom). Be sure to wipe everything from recovery before that.
If that fails, you should get the official rom for your location and flash it with kdz (there is a very well done guide here on XDA for doing that, search for it).
And consider flashing Void next time, is more stable and has the same features (and more) as Megatron (hwacc, jit, oc, stagefright etc).
In any case, if the phone boots, even if gets stuck on LG splash screen, it is not bricked. It can be re-flashed easily, just follow the steps in the guides.
How to flash original rom: http://forum.xda-developers.com/showthread.php?t=875881
Original rom list: http://forum.xda-developers.com/showthread.php?t=865479&highlight=stock+rom
thank you so much for the reply but for some strange reason i cant put my phone into recovery or emergency mode. idk why and i tried like all the button presses. Do you hold them down or press them in order. im sry for being a noob lol. but u gave me hope knowing now its not bricked
deathmill3001 said:
thank you so much for the reply but for some strange reason i cant put my phone into recovery or emergency mode. idk why and i tried like all the button presses. Do you hold them down or press them in order. im sry for being a noob lol. but u gave me hope knowing now its not bricked
Click to expand...
Click to collapse
press and hold down HOME + VOL DOWN while the phone is off, then turn it on, keeping that 2 buttons pressed until recovery appears.
But if you have used rom manager, this won't work. Your only chance to unbrick is this: http://forum.xda-developers.com/showthread.php?t=883314
rom manager don't support yet optimus t
The same happened to me when I flashed LOL rom. I was reading that it can sometimes take up to 5 minutes to reach the boot animation. My phone reached the boot animation in 6-7 minutes. How long did you wait before you removed the battery?
thats not working either. all i saw was a bunch of ppl with the same problem and eventually sent it to LG service
ummm like about 3 minutes cause i was freaking out lol. that could be it :/
deathmill3001 said:
ummm like about 3 minutes cause i was freaking out lol. that could be it :/
Click to expand...
Click to collapse
I was about to pull mine out too after 3-4 minutes. I was freaking out also but had to go to the washroom when this happened. When I came back, the phone booted. If I didn't use the washroom, I would have bricked my phone, lol.
A lot of people have this problem because on the Optimus One it takes forever to load the first time. My samsung vibrant was extremely quick, 1 minute max
as soon as u send to warranty, the faster u get ur usable phone back
or just use it as vibrator
shadow_cruiser said:
I was about to pull mine out too after 3-4 minutes. I was freaking out also but had to go to the washroom when this happened. When I came back, the phone booted. If I didn't use the washroom, I would have bricked my phone, lol.
A lot of people have this problem because on the Optimus One it takes forever to load the first time. My samsung vibrant was extremely quick, 1 minute max
Click to expand...
Click to collapse
lol lucky u. idk this was my first android phone and i still have 1 year and 8 months left on my contract so i have no clue on what to do :/