@All
i've Bricked (killed) my HTC mega, i just flash it with wrong file and after that it stuck on HTC logo so i just connected it with MTTY and used few commands and it doesn't power on , mean doesn't take power at all now , i used following commands.
1) i connected it with MTTY in Bootloader.
2) i open MTTY
3) i type info 8 (it shows me it have bad blocks)
4) i type task 2a (it says can't reapir Bad Blocks)
5) i type task 8 phone turned off and then no power at all.
i think there is a solution with JTAG to revive dead phone there was no problem at all with Phone before only need to change from Chinese to English language.
if there is any help kindly post it here.
Take Care
ENJOY
your device go in bootloader? If yes download original rom for your device, power on device with volume down pressed (three colored bars appears), connect with usb and flash original rom. For download correct rom search in this thread:
http://forum.xda-developers.com/showthread.php?t=578915
or search your rom here:
http://htcpedia.com/soft/mega-touch2-rom.html
http://shipped-roms.com/shipped/Mega/
If you have issue executing this procedure please i try to help you
fabcal the phone doesnt even turn on as the thread owner mentioned ... so none of your methods will work for him ....
LtBlue said:
fabcal the phone doesnt even turn on as the thread owner mentioned ... so none of your methods will work for him ....
Click to expand...
Click to collapse
it is true that he says that the phone will not turn on. But from my experience in the assistance of computers, the user loads the fact that the system is reported as "not turn on ". You have no idea how many times I went home carrying the replacement power supply because they said "not turn on", when they appeared "disk boot failure!" and the same thing I already happened with Italian users of smart phones. White screen at power on, boot loader ok but the owner stated that power on. I explained?
Ascolta
Trascrizione fonetica
Dizionario - Visualizza dizionario dettagliatocongiunzione0.and
Project dead
Related
help me please my device is dead how can i backup it agian
if any one know help me the story is when i do a hard rest and make an upgare the imate tyoe in the screen that is erasing rom and the is shut down and now when i repack to update is give me this screen shot what i do
Try pressing "Power Button" + "Reset Button" + Directional Pad (the center) Button" then you will go to boot screen.. If you see "Serial" on top and "v1.06" below try docking the device on the cradle then reflash.. reply asap with the result..
i try this but no answer
what can i do please
alloooooooooooooooooo i want any answer plz
Here... Put this file "HimaClearJumpCode.exe " in the same directory as the ROM and installer and it should work this time...
Also, try to use the power supply connected to the cradle, sometimes the power provided through the USB cradle is not enough.
If it works, chances are you will get another error "Country Error". If that's the case, use the attached file "himaupgradeut_197.exe" instead, this will skip the country check.
Good Luck!
Rayan
my friend it dose not work what can i do please i want to repaire it and i can't do that and how does it work please insert some picture about the steps to understand that
and thank you again about your steps
Please describe what you see on the PDA screen when you power up?
Does it boots all the way into the Windows Mobile Today screen?
Do you only see the word "Serial" on a blank screen?
Please provide more details.
the details is
1- when i put the pda in the cradel it is give me the red light but this happen without put the battery in the pda the problem is when i put the battery in the pda it give me no light
2- i changed the battery but no answer
3- i try to put it in the cradel and recharge for 1 night and put it in the pda but now answer
4- i read abut reflashing but this is very hard and i can't see any replay abut that
5- now i want to tell you the summry when i put the pda with the battery and it full cahrge it give me now answer and the active syn did not find any thing and on the screen there is nothing not serial and not usb ver the screen is black
please tell me i'm in egypte and no one know to repaire it
what can i do
Sorry, but as far as I know, you will not be able to reflash if you can't boot or at least see the bootloader screen (blank screen with SERIAL text).
May I ask, what caused this problem in the first place?
What model do you have? Himalaya, Alpine, Wallaby, etc...
i have himalaya 1.2
is this write or not
where are you
do you know waht i must to do my friend
where are you
no one know
Can you tell me what will you see if in your screen if you press the "Power Button" + "reset Button" + Directional Pad Button (The center one)? cuz thats the best you ca do...
my friend when i connected the power my device is not work how?! because when i put the battery in the device it gives me that no power in the device ,then i changed the battery but the problem still appear when i put the device in the cradel the red light becomes work but this happend when i put it without battery now when i put the battery the device turn off the red light and not give me any thing now i want to give the device power
how can i do that and how can i fix the screen that tell me that the device is not in the cradel this screen is apper for me my frindes
and when i press that buttons nothig happen i don't know waht but now i want to give the device the power how can i do that do you have any answer about that
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
john72821 said:
I need to upgrade the SPL on my SPV C550 now that I have unlocked it (trying to install WM6)
Do I have to buy a mini SD card reader or can I use tools to do this from my PC.
If so which tools please and briefly how.
Cheers
John
Click to expand...
Click to collapse
Although a search would solve your problem here is a mini how to:
- you need to have ParchedRUU (this includes these files: EnterBootLoader.exe, Patched_RUU.exe, ROMUpdateUtility.exe, RUUGetInfo.exe and finaly your_bootloader_name.nbf) all in the same directory. The files are availabe on the net just google it.
- establish an activesync connection with USB, to do so have the phone in standby mode (no bootloader mode)
- when connected in activesync (green icon on taskbar) run the Patched_RUU.exe
- make sure you tick the boxes and the next button and that phone battery is greater than 50%
- in the final screen hit the update button, if the .nbf is in the same directory as the Patched_RUU it will load it automatically
- wait for 3 minutes, during this time you phone will enter bootloader mode, and a red bar will show the progress on the phone and the computer
you are all done
- mike
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
john72821 said:
Cheers mate that did the job.
Next I guess I get into boot loader mode and then use mmty.exe?
Any clues please on how to get into boot loader mode.
Click to expand...
Click to collapse
again search m8!
anw here it goes:
- go to active sync -> settngs -> disable USB connections
- switch off your phone, and while holding the camera button connect it to the USB, on the screen it will appear "Need UI upgrade? (0)" or something like that.. bottom line is press 0
- then phone enters bootloader mode. if on the lower bar i think it is the green bar it says hurricane and on the right UI then it is all good, if it says something like XIP or something then you have to switch it off and do the proccess from the begining with the camera button REMEMBER TO PRESS THE 0
- fire up the mtty.exe, remember put mtty.exe AND the bin in the C:\ directory. The only thing you need to change in the startup screen of mtty is the connection port change from com1 or something to usb and press ok
- press enter so the Cmd> shows on the blank terminal
- write without quotes "l c:\name_of_your_rom.bin" and hit enter. l is a small L short for load
- hopefully it will do the update, wait for ~10 mins and it will say that it is all done... depending on your rom you may have to change language and so...
hope this helped
- mike
Sorry to carry on a bit but I get this when I do what you suggested.
Cmd>l C:\wm6.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Ive Googled this and im sure ive unlocked my phone - but is that the same as unlocking the super CID?
i dont remember man, are we allowed to post links to other sites? anw follow this guy's tutorial it is allmost the same
http://karhoe.byethost33.com/content/view/35/1/
- mike
help..
need to flash phone from boot loader mode..no standby mode..how do i do that???
HELP!!!!!!!!!!!
Just follow my guide in the signature, but use huricane ROM instead, you need to get into the bootloader and enable AS USB mode, then run the RUU
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
DEAD SPV
i hv made a mistake while upgrading my spv c550(HTC Hurricane) to wm6.
i have flashed the wrong spl SPL 1.01.0109 on my fone. that spl was of htc typhoon.
now my phone is not booting up.
when i press the power button the fone gives the white disply and nothing else happens.
i cannot even get into bootloader.
the charging function works when the fone is turned off.
when i turn on the fone it dos nothing not even chaging.
is there any way to get my old fone back...
help plz
i shall be very thankfull to you.
Where I can find the latest SPL for C550?
Dear All:
I bricked my device unfortunately. I am trying to go to bootloader mode but it's not working. I pressed down simultaneously the botton right below the volume down botton and the opposite botton. While both bottons pressed, I powered on the device.
However unfortunatley, it's not working. Please advise the propoer bootloader sequence for HTC Startrek / imate smartflip.
Note I can not use jumpSPL simply because the device is brick and not booting
Samer.
samery said:
Dear All:
I bricked my device unfortunately. I am trying to go to bootloader mode but it's not working. I pressed down simultaneously the botton right below the volume down botton and the opposite botton. While both bottons pressed, I powered on the device.
However unfortunatley, it's not working. Please advise the propoer bootloader sequence for HTC Startrek / imate smartflip.
Note I can not use jumpSPL simply because the device is brick and not booting
Samer.
Click to expand...
Click to collapse
Don't power it on, while pressing both buttons, hold it, and connect your device to your pc. It will turn itself on in bootloader mode. After that install an official rom...
Pampooh said:
Don't power it on, while pressing both buttons, hold it, and connect your device to your pc. It will turn itself on in bootloader mode. After that install an official rom...
Click to expand...
Click to collapse
Thank you, it worked like a charm, however unfortunatley there is no luck.
Let me start by saying that I am trying to install your ROM, so I am delighted that you have personally answered me.
It went to bootloader mode, then after checking the image it returned saying Invalid Certificate.
Then I launched RomUpdateUtility from my laptop to try to install the ROM, it starts writing the ROM, then at 4%, the mobile restarts, and the upgrade utility displays Image Corrupted.
I tried to bring a different (WM6.1 SLIM found somewhere here in this forum) and copied the file to the memory, but received the same "invalid certificate" error.
May I ask you to please suggest a resolution for this problem? thanking you.
Sincerely yours.
Samer.
Hamdullilah it works.
I figured that if the rom is having a certificate error with the device then I should be able to return to the original rom.
so I went to ftp.clubimate.com and downloaded the original rom and install it, so it did successfully.
then I restarted the upgrade process only this time I did NOT do the same mistake again (not restarting after SDA Unlock) and i got my mobile running now like a sharm on Pampooh rom.
Thanks Pampooh, you are a saver.
Have a great day.
Samer.
Congratulations. Although I would suggest that you use the ROSE release since it uses less memory and is a bit faster than the NEO release. If you do decide to use the ROSE rom, try out PointUI Home2, it looks great. I have the download link in my 1.05b ROSE thread. Good day to you too.
true, but I used a WM6.1 slim version for a long time so it's time to change. The Neo interface is amazing and i dont really care about size, If needed, I could always use the external micro SD for storage.
I think NEO rom is fabulous, you should try it
ı want to load WM 6.1 V2 Pro to my smartflip. but when it is %52 the error occurred. than the phone is closed. when ı was open it the htc picture comes and the phone dosnt open . ı cant load it again because the phone dosnt connect to pc whit usb. please help me what ı must do?
which keys ı must press for bootlooder? please help me.
lanu42 said:
ı want to load WM 6.1 V2 Pro to my smartflip. but when it is %52 the error occurred. than the phone is closed. when ı was open it the htc picture comes and the phone dosnt open . ı cant load it again because the phone dosnt connect to pc whit usb. please help me what ı must do?
which keys ı must press for bootlooder? please help me.
Click to expand...
Click to collapse
volume down botton and the opposite botton. Hold it, and connect your device to your pc. It will turn itself on in bootloader mode. After that install an official rom...
All,
I inherited a seriously injured HTC surround, and I have decided to use it as a project phone.
Current status - Half Bricked on the bootloader + when it boots it immediately asks to be connected to restore backup. Unfortunately I have no zune backup and neither does the original owner of the device.
So I have read everything I could find on the half-brick issue and it seems that some folks are having success using the goldcard method to over write their boot loader with various HTC devices. I am will to try this but all the vids I have seen tutorials etc show that you have to put the device into enter usb host mode (blue writing on white screen)
Only problem is ....I have no idea how to do this on the Surround. I have tried every button combo on boot and cannot find it.
Someone here must know how to do this in return I will post my findings on whether or not the Goldcard trick works to repair a 1/2 brick surround.
Thanks
rob243 said:
All,
I inherited a seriously injured HTC surround, and I have decided to use it as a project phone.
Current status - Half Bricked on the bootloader + when it boots it immediately asks to be connected to restore backup. Unfortunately I have no zune backup and neither does the original owner of the device.
So I have read everything I could find on the half-brick issue and it seems that some folks are having success using the goldcard method to over write their boot loader with various HTC devices. I am will to try this but all the vids I have seen tutorials etc show that you have to put the device into enter usb host mode (blue writing on white screen)
Only problem is ....I have no idea how to do this on the Surround. I have tried every button combo on boot and cannot find it.
Someone here must know how to do this in return I will post my findings on whether or not the Goldcard trick works to repair a 1/2 brick surround.
Thanks
Click to expand...
Click to collapse
Hi,
Power off the device
Press and HOLD both camera and volume down buttons
Press power on button and KEEP holding both battery and volume down buttons
After boot screen will follow the usb screen
Now release battery and volume down buttons
Regards, ansar
Ok I can only get to the tricolor screen showing the 1/2 brick spl. is the the usb host mode? Because I see on some videos on youtube a white screen with blue writing that says enter usb host mode. This is what I am trying to achieve.
Or if this is the USB host mode should I just attempt to do the flash via gold card and see if I can get rid of teh 1/2 brick?
USB Host mode
To enter USB host mode turn off the phone, then press and hold VOL down + camera buttons, then press power.
But the phone will not enter USB host mode if you only see one line en the tricolor screen (this state is half bricked). For the phone to be able to enter USB host mode, the tricolor screen must have more than 1 line but the only missing part must be Serial/USB at the bottom. Check well the videos on youtube, and you will notice before entering USB host mode that the tricolor screen have more than 1 line (someone call this state small half bricked).
My phone is also half bricked (one line in the tricolor screen), the only solution I have found is to do an HTC OEM update, either by waiting for HTC to release an update (that includes a bootloader) through zune or by forcing it (for this the phone needs to be developer unlocked).
P.S. ChevronWP7 is not selling more unlocking tokens at the moment, and the $99 AppHub membership is too expensive for me.
Thanks Guys
After reading your posts I tried it out on my good surround and sure enough was dumped directly into Enter USB Host Mode screen
So now I am sitting here wondering what can I do with this thing it will not boot to anything but the screen to connect to restore backup.
Could I give anyone here anything useful about the device? Maybe disect it and post pics? Maybe someone could find these jtag posts? Or keep it for spare parts? Seems like a waste to just chuck it
Maybe you can repair it
rob243 said:
After reading your posts I tried it out on my good surround and sure enough was dumped directly into Enter USB Host Mode screen
So now I am sitting here wondering what can I do with this thing it will not boot to anything but the screen to connect to restore backup.
Could I give anyone here anything useful about the device? Maybe disect it and post pics? Maybe someone could find these jtag posts? Or keep it for spare parts? Seems like a waste to just chuck it
Click to expand...
Click to collapse
rob243, you can try to install a new firmware, depending if the firmware is a version inferior to 2250.21.40500.502. You can use a tool called Cab Sender (http://forum.xda-developers.com/showthread.php?t=1306415) to send firmware version mondrian_2250.21.40500.502.cab (search in xda-developers), for the enter the phone to recovery mode (just press and hold CAMERA, then power, ang then release the 2 buttons).
Good day to you all kind folks!
Basicly, i have the same problem as mr. adijat from http://forum.xda-developers.com/showthread.php?t=1816263 .
I was digging about link2sd with the phone from the subject and messed it up.
I managed to get it to boot to android again, but with limited capability:
1. Once connected to PC, it only charges, no mass storage, no usb debuging, no nothing.
2. Half of the applications are missing, like GooglePlay, Google Account Sinchronization etc.
I did try to install those manually, but to no avail, if i try to install GooglePlay.apk it just says: Application not installed.
I was google-ing for a way to adb push those applications, but i have no idea what parts of android system are responsible for USB controlers, and every try to find out doesnt end so good.
As for the original stock rom/firmware from huawei, they DO have the phone listed on their download page, but nothing to download from there, and from another sites i cant seem to find the specific rom for this model, although i've tried to install some similar ROMs like official U8650 and S8600, none worked ( when i enter in update screen, step 1/2 finishes and as soon as step 2/2 starts it says "Update Failed" and thats it.
I can't seem to get it to fastboot mode anymore also (Shut down > Plug to PC > Volume down+Power 2 sec > 10 sec Power ), because when i plug it in to PC while its shut down it doesnt go to battery charging screen, it just stays on white loading screen.
I'm baffeled with this, i'm not much of an expert on this stuff but i know the basics, and cant figure it out.
If anyone has any solutions, it would be great!
Greetings from Croatia and I'm sorry in advance if i posted in wrong part of the forums, this is the best i could find.
bagio007 said:
Good day to you all kind folks!
Basicly, i have the same problem as mr. adijat from http://forum.xda-developers.com/showthread.php?t=1816263 .
I was digging about link2sd with the phone from the subject and messed it up.
I managed to get it to boot to android again, but with limited capability:
1. Once connected to PC, it only charges, no mass storage, no usb debuging, no nothing.
2. Half of the applications are missing, like GooglePlay, Google Account Sinchronization etc.
I did try to install those manually, but to no avail, if i try to install GooglePlay.apk it just says: Application not installed.
I was google-ing for a way to adb push those applications, but i have no idea what parts of android system are responsible for USB controlers, and every try to find out doesnt end so good.
As for the original stock rom/firmware from huawei, they DO have the phone listed on their download page, but nothing to download from there, and from another sites i cant seem to find the specific rom for this model, although i've tried to install some similar ROMs like official U8650 and S8600, none worked ( when i enter in update screen, step 1/2 finishes and as soon as step 2/2 starts it says "Update Failed" and thats it.
I can't seem to get it to fastboot mode anymore also (Shut down > Plug to PC > Volume down+Power 2 sec > 10 sec Power ), because when i plug it in to PC while its shut down it doesnt go to battery charging screen, it just stays on white loading screen.
I'm baffeled with this, i'm not much of an expert on this stuff but i know the basics, and cant figure it out.
If anyone has any solutions, it would be great!
Greetings from Croatia and I'm sorry in advance if i posted in wrong part of the forums, this is the best i could find.
Click to expand...
Click to collapse
bagio007 do not try to restore with another roms because it is useless. try it only with fastboot ...
you nedd to boot in recovery mode and try to flash with fastboot
boot.img
recovery.img
system.img
STEPS:
Turn off the phone, disconnect the USB cable and remove the battery
Reinsert the battery into the phone
Turn on phone into fastboot mode
Press the volume up button for 1 second.
Holding volume up, press the power button, holding down both buttons for 4 seconds.
After that, release the power button first, then the Volume Up button.
The screen should remain black ...
Try to reset factory a prhone in recovery mode ..
move the bar with volume up/down key and power button to accept
if not wort thats try to flash with fastboot
Reconnect the phone and verify, that the phone is in fastboot. Type into the Command Prompt or terminal:
fastboot devices
Now flash the firmware:
fastboot flash boot /path/to/boot.img
fastboot flash recovery /path/to/recovery.img
fastboot flash system /path/to/system.img
fastboot flash userdata /path/to/userdata.img
Reboot the phone
fastboot reboot