I have a malfunction usb connector so usb data transfer or my jig is not working anymore. The data cable and the jig is tested on another I9100, and they worked well. Surprisely the 3key download mode is working, and firmware flash with odin too.
So I need an alternate way to reset the counter before I send it back to warranty service
Is it stored in the bootloader? Can I reflash it with odin?
KeFe said:
I have a malfunction usb connector so usb data transfer or my jig is not working anymore. The data cable and the jig is tested on another I9100, and they worked well. Surprisely the 3key download mode is working, and firmware flash with odin too.
So I need an alternate way to reset the counter before I send it back to warranty service
Is it stored in the bootloader? Can I reflash it with odin?
Click to expand...
Click to collapse
there is no known alternative way of resetting the counter, if it was as simple as using odin then we would have never worried about using a jig.
So then what is the best way to make a total brick? (result: no 3key recovery or download mode)
I should mess with the bootloader in odin?
KeFe said:
So then what is the best way to make a total brick? (result: no 3key recovery or download mode)
I should mess with the bootloader in odin?
Click to expand...
Click to collapse
LOL!! This is the reverse "I bricked my phone" thread. It's the first time I've seen someone asking how to brick their phone.
I suggest you look at the above mentioned "Hallppz!! I broked mi fonnee" threads and do exactly what they did to brick their phones. Stuff like flashing SGS firmware on SGS2 can help.
aydc said:
LOL!! This is the reverse "I bricked my phone" thread. It's the first time I've seen someone asking how to brick their phone.
I suggest you look at the above mentioned "Hallppz!! I broked mi fonnee" threads and do exactly what they did to brick their phones. Stuff like flashing SGS firmware on SGS2 can help.
Click to expand...
Click to collapse
Can help, but will be detectable. just start a flash with odin and unplug halfway through, you'll get a connect to pc screen and wont be able to acces download mode
It is the first destructive thread in this forum, isn't it?
dh2311 said:
Can help, but will be detectable. just start a flash with odin and unplug halfway through, you'll get a connect to pc screen and wont be able to acces download mode
Click to expand...
Click to collapse
Thx
I'll try it tomorrow in the evening unless somebody comes up with a better idea.
I'll post here the result
AFAIK, samsung service center won't check for "flashed" phones. When I returned my SGS2(just cf-rooted), they said I should return after 30mins because they'll flash it back to default(They didn't even check, they just said that while I was still filling-up their repair form). But my yellow tint was still there, so I got a new phone. Now no yellow tint visible on the eyes.
gr8... hope i
dont hav to visit warrnty ever..
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to Q&A
Related
I've a I9100 and for certain hardware issue (Audio problem) I want to send it to the Service Center.
I tried different custom ROMs before coming back to 2.3.3 KE8 through ODIN as I realized the hardware issue was not gonna fix without sending it for repair or replacement.
Now, I bought USB Jig from Ebay and followed the instructions in the USB Jig FAQ thread but after switching the phone off and inserting the USB Jig it is not booting into the Download Mode ? Is the USB Jig not working ?
Or do I need to flash an old bootloader to get this working , if yes a link please ?
Yes most probably thats a bootloader issue...get an old bootloader from the Original Dev Subsection.
Mine for some reason doesn't automatically boot when the jig is inserted but it does do it's job when I just use the power button to switch on.
Then it boots into download mode and resets triangle and flash counter.
Don't know why. I bought it for my sgs1 so maybe thats something.
Anyway try doing it that way and see how you go.
Sent from my GT-I9100 using XDA App
I flashed the old bootloader posted in the intratech's thread here Still its not booting up.
And also, I tried inserting the Jig and then powering on manually that didn't work as well.
What now ?
Some peoples have posted on other forums about the USB jig doesn't work automatically when inserted (although it should...) Try inserting the jig, and powering your phone on. It should reset the flash counter, if you are trying to get rid of the triangle for "warranty" purposes
Are you close to any of these people?
http://forum.xda-developers.com/showthread.php?t=1495867
Might be able to try a different jig just in case it's a dud.
Sent from my GT-I9100 using XDA App
tricurious said:
I've a I9100 and for certain hardware issue (Audio problem) I want to send it to the Service Center.
I tried different custom ROMs before coming back to 2.3.3 KE8 through ODIN as I realized the hardware issue was not gonna fix without sending it for repair or replacement.
Now, I bought USB Jig from Ebay and followed the instructions in the USB Jig FAQ thread but after switching the phone off and inserting the USB Jig it is not booting into the Download Mode ? Is the USB Jig not working ?
Or do I need to flash an old bootloader to get this working , if yes a link please ?
Click to expand...
Click to collapse
2.3.3 KE8 Has the old the old bootloader so no need to replace it..
Try cleaning the usb port with a spray duster or tooth brush and try jig again.. Also you may be unlucky with a DOA Jig...
Hey I just couldn't get the USB Jig working so I had no other option but to try the riskier method.
So, I updated to ICS (Resurrection Remix 9.3) and used TriangleAway and it worked. Then I flashed the Stock Rom by using Mobile Odin.
So now the phone is as "Factory'd" as possible and I'll be taking it to the service center tomorrow
@ All above, thanks for helping
aceofclubs said:
Are you close to any of these people?
http://forum.xda-developers.com/showthread.php?t=1495867
Might be able to try a different jig just in case it's a dud.
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
No unfortunately I wasn't. The closest one was 540 Miles away
tricurious said:
Hey I just couldn't get the USB Jig working so I had no other option but to try the riskier method.
So, I updated to ICS (Resurrection Remix 9.3) and used TriangleAway and it worked. Then I flashed the Stock Rom by using Mobile Odin.
So now the phone is as "Factory'd" as possible and I'll be taking it to the service center tomorrow
@ All above, thanks for helping
Click to expand...
Click to collapse
I'm glad you managed to remove the Triangle and restored to the stock rom,but what about the rom counter? The Service guys will surely check for the rom counter....you managed to reset that too?
yashleo21 said:
but what about the rom counter? The Service guys will surely check for the rom counter....you managed to reset that too?
Click to expand...
Click to collapse
Yeah the "TriangleAway" app resets the Binary Counter too
Seems like a dud jig to me. Mine automatically boots into download mode, regardless of bootloader.
Sent from my GT-I9100T
I had these issues - installed the old bootloader and away went the yellow triangle after inserting the USB Jig.
The counter would not reset but I found a "GT-I9100_counter_patch.tar" file which I flashed (PDA) and then inserting the USB Jig it reset the binary counter to zero
PM me if you would like the patch file
So i need to send in my phone for repairs because my battery gets drained like crazy and i tried everything to stop it. (dozen different roms/kernels completely "naked" without ANY apps and it still drains ~10% an hour).
so anyway, my JIG worked fine all the time (got me into download mode every time), but since i need to reset the binary counter i flashed the XWKG1 firmware and the old bootloader through odin and everything works fine, except my JIG does not bring me into download mode anymore. when i plug it in, the phone just boots normally. i can get into download mode with 3 button method but it just shows me that the counter is still on 1.
any suggestions?
searching for this matter is kinda hard, because "jig not working" brings up all kinds of threads about the jig not resetting due to newer bootloader, and "jig not starting download mode" doesnt bring the desired results either.
so any help would be much appreciated.
greetz
strange!!!
Home made jig or purchased one? Sometime any short circuite on the jig resisters???
if available try with another jig...
you can flash again old bootloader and try.
purchased one. i already opened it up to check for short circuit, and the color coding of the resistor is correct aswell (301k)...
phoboss said:
purchased one. i already opened it up to check for short circuit, and the color coding of the resistor is correct aswell (301k)...
Click to expand...
Click to collapse
lol u sayin ur jig is not working????well wat u need it for download mode or resetin counter...
phoboss said:
So i need to send in my phone for repairs because my battery gets drained like crazy and i tried everything to stop it. (dozen different roms/kernels completely "naked" without ANY apps and it still drains ~10% an hour).
so anyway, my JIG worked fine all the time (got me into download mode every time), but since i need to reset the binary counter i flashed the XWKG1 firmware and the old bootloader through odin and everything works fine, except my JIG does not bring me into download mode anymore. when i plug it in, the phone just boots normally. i can get into download mode with 3 button method but it just shows me that the counter is still on 1.
any suggestions?
searching for this matter is kinda hard, because "jig not working" brings up all kinds of threads about the jig not resetting due to newer bootloader, and "jig not starting download mode" doesnt bring the desired results either.
so any help would be much appreciated.
greetz
Click to expand...
Click to collapse
If the jig is working properly then you should get to dl mode with old bootloader. You can get info regarding how to install it here http://forum.xda-developers.com/showthread.php?t=1075278 and here http://www.jayceooi.com/2011/12/23/...oader-on-samsung-galaxy-s2-to-enable-usb-jig/
rocky23 said:
lol u sayin ur jig is not working????well wat u need it for download mode or resetin counter...
Click to expand...
Click to collapse
thats exactly what i'm saying. i have the right firmware, and the right bootloader flashed, but when i plug in my JIG the phone boots normally. i can get into download mode with volume down+home+power but that way i cant reset my binary counter.
Logic says buy a new USB jig as the cost is so small .
jje
yeah already orded one. weird though that it stopped working from one minute to the next.
phoboss said:
yeah already orded one. weird though that it stopped working from one minute to the next.
Click to expand...
Click to collapse
do post if the new jig works.......cheeeeerz
same problem!
phoboss said:
yeah already orded one. weird though that it stopped working from one minute to the next.
Click to expand...
Click to collapse
any news?? i have the same problem. mine is home-made and sealed shut (bathed in hot-glue and visible below). one moment working (dwnload) the next: nope (nrml boot).
I'm a noob and I know it
Try noteiangle app. So perfect.
Sent from my GT-I9100 using XDA
Check if in Developer option / USB debugging is selected then power off the phone and use usb jig
Using XDA Premium over Resurrection Remix ICS, the Best Rom ever made
deltasync said:
Check if in Developer option / USB debugging is selected then power off the phone and use usb jig
Click to expand...
Click to collapse
it is on mine. Still no go...
Sent from my GT-I9100 using XDA
dalelerah said:
it is on mine. Still no go...
Sent from my GT-I9100 using XDA
Click to expand...
Click to collapse
debugging will not make any difference...
even if you keep posting, you dont get any suggestions other than below :
1) try your jig on any other phone
2) try with new jig
3) try flashing old bootloader again
Everythig fail, flash ICS and use Triangle Away app.
ZACQ8 said:
debugging will not make any difference...
even if you keep posting, you dont get any suggestions other than below :
1) try your jig on any other phone
2) try with new jig
3) try flashing old bootloader again
Everythig fail, flash ICS and use Triangle Away app.
Click to expand...
Click to collapse
Yeah I guess. Bootloader is not the problem, as it worked before. Plus, according to other threads, ICS bootloader works with jig, but it only force-boots to download, not flashing Odin counter. As stated, that doesn't even work.
I'm a noob and I know it
Hello,
I am new to the S2 forum. I have purchased the phone on Dec 04. It came with firmware version 4.0.4.
The PDA was I9100XWLPW and CSC was I9100ODDLPC.
After a week, I flashed the leaked JB firmware XXLSJ and used PhilZ cwm6 kernel to obtain root.
I was not having any problems until today.
I was using the phone normally, it had about 60% battery. Suddenly it was not waking up ( The phone was not used for about 15min ). I tried removing the battery, all button combinations but was not booting normally or into recovery. I could get into the download mode by plugging the phone to the PC. Odin failed to flash the official FW and the JB leak. I followed the thread http://forum.xda-developers.com/showthread.php?t=1457458 and found out it was a corrupted NAND r/w function.
I tried doing all the steps given in the thread. Now my phone does'nt go into the download mode and does'nt show charging when plugged to a power source.
Can I recover my phone?
Please someone help me or guide me to a previous post that solves this problem!!
Edit: Samsung service has replaced the mother board!!
Doing the pit partition has resulted in my phone getting bricked!!
So people new to the forum, never do it :laugh:
Hi,
You said you couldn't access download mode, but can you access CWM recovery?
If you can then, you should wipe data/factory set, wipe cache and wipe Dalvik-cahe. after that you should re-flash your ROM.
If that doesn't work, maybe you should restore your CWM/Nandroid backup of your ROM before you flashed the JB leak XXLSJ, which in this case seems to be Stock ROM. (providing that you have backed it up in the first place)
Greetz and Happy new year
CashAndPotatoes said:
Hi,
You said you couldn't access download mode, but can you access CWM recovery?
If you can then, you should wipe data/factory set, wipe cache and wipe Dalvik-cahe. after that you should re-flash your ROM.
If that doesn't work, maybe you should restore your CWM/Nandroid backup of your ROM before you flashed the JB leak XXLSJ, which in this case seems to be Stock ROM. (providing that you have backed it up in the first place)
Greetz and Happy new year
Click to expand...
Click to collapse
I am unable to get into recovery mode also.
The phone does not respond to any button-combos or connecting to computer or a power source!!
Pradeep said:
I am unable to get into recovery mode also.
The phone does not respond to any button-combos or connecting to computer or a power source!!
Click to expand...
Click to collapse
HI,
today I wake up with the same problem.(Bug from the junary 1st???). I'm on Leak 4.1.2 too
Mi Galaxy sII don't charge the batery (loop from charge batery symbol) All the combination button don't wake up the phone.
The only thing seem working is the download mode. Don't try to connect to ODIN for the moment.
Any idea?
Pradeep said:
I am unable to get into recovery mode also.
The phone does not respond to any button-combos or connecting to computer or a power source!!
Click to expand...
Click to collapse
Remove battery for some time re insert it and see .
Or
Try a jig
leap before you think
Pradeep said:
Hello,
I am new to the S2 forum. I have purchased the phone on Dec 04. It came with firmware version 4.0.4.
The PDA was I9100XWLPW and CSC was I9100ODDLPC.
After a week, I flashed the leaked JB firmware XXLSJ and used PhilZ cwm6 kernel to obtain root.
I was not having any problems until today.
I was using the phone normally, it had about 60% battery. Suddenly it was not waking up ( The phone was not used for about 15min ). I tried removing the battery, all button combinations but was not booting normally or into recovery. I could get into the download mode by plugging the phone to the PC. Odin failed to flash the official FW and the JB leak. I followed the thread http://forum.xda-developers.com/showthread.php?t=1457458 and found out it was a corrupted NAND r/w function.
I tried doing all the steps given in the thread. Now my phone does'nt go into the download mode and does'nt show charging when plugged to a power source.
Can I recover my phone?
Please someone help me or guide me to a previous post that solves this problem!!
Click to expand...
Click to collapse
We already have plenty of topics about this why do you feel the need to create another? Your symptoms are no different to others and the answers are no different.
If you cant access download or recovery and cant power on then try a USB jig. If that doesnt work then you will need to take/send it for repair which will either be JTAG or complete mobo replacement.
Just because you create your own topic it doesnt mean answer is going to be any different.
Gediprime said:
HI,
today I wake up with the same problem.(Bug from the junary 1st???). I'm on Leak 4.1.2 too
Mi Galaxy sII don't charge the batery (loop from charge batery symbol) All the combination button don't wake up the phone.
The only thing seem working is the download mode. Don't try to connect to ODIN for the moment.
Any idea?
Click to expand...
Click to collapse
If you can access download mode, use it. Try re-flashing your kernel.
nikufellow said:
Remove battery for some time re insert it and see .
Or
Try a jig
leap before you think
Click to expand...
Click to collapse
JIG ???
Gediprime said:
JIG ???
Click to expand...
Click to collapse
Use the search button and use keywords "usb jig". Or google.
TheATHEiST said:
We already have plenty of topics about this why do you feel the need to create another? Your symptoms are no different to others and the answers are no different.
If you cant access download or recovery and cant power on then try a USB jig. If that doesnt work then you will need to take/send it for repair which will either be JTAG or complete mobo replacement.
Just because you create your own topic it doesnt mean answer is going to be any different.
Click to expand...
Click to collapse
I am sorry!! I am new to this forum and the phone being a recent purchase, i was very much desperate!!
I know the answer may not be different and the problem may not be new hence I've asked to guide me to the appropriate thread in my post!! No offence!!
Thanks for your reply. I will be taking the phone to Samsung Service tomorrow.
Gediprime said:
JIG ???
Click to expand...
Click to collapse
3 100k resistors + 1k resistor in series connected between 4 and 5 pins of a male usb end when plugged will get you into download mode in case of soft bricks .
leap before you think
TheATHEiST said:
We already have plenty of topics about this why do you feel the need to create another? Your symptoms are no different to others and the answers are no different.
If you cant access download or recovery and cant power on then try a USB jig. If that doesnt work then you will need to take/send it for repair which will either be JTAG or complete mobo replacement.
Just because you create your own topic it doesnt mean answer is going to be any different.
If you can access download mode, use it. Try re-flashing your kernel.
Click to expand...
Click to collapse
I try it but when a push up level button my phone loop again to charging symbol (without charging)
Sorry if this post is the same than another. For my part i'm just trying to find a solution. A have plenty of corporative information on my phone. I do my last backup one weeks ago :crying:
nikufellow said:
3 100k resistors + 1k resistor in series connected between 4 and 5 pins of a male usb end when plugged will get you into download mode in case of soft bricks .
leap before you think
Click to expand...
Click to collapse
In some of the posts, I've read that a JIG may not work on ICS based roms!!
Is this true?? Should I try a JIG first before I take the phone to Samsung Service??
I was on XXLSJ before the phone went dead!!
Gediprime said:
I try it but when a push up level button my phone loop again to charging symbol (without charging)
Sorry if this post is the same than another. For my part i'm just trying to find a solution. A have plenty of corporative information on my phone. I do my last backup one weeks ago :crying:
Click to expand...
Click to collapse
I had the same problem.. I could get into the download mode by:
1. Phone completely OFF state
2. Connect the USB cable to the phone and PC ( The battery charging indication has to come, atleast once )
3. Fire up ODIN
4. Get the phone into download mode ( Vol-down+home+Power ) while the phone is connected
5. The phone is now recognized by ODIN.
I could flash a kernel (tried siyah and Philz) but the phone was not booting.
While trying to flash Stock and XXLSJ, ODIN was getting failed at factoryfs.fs
After a few trys, the phone just went dead!!
Hope you can flash a firmware successfully :good:
Pradeep said:
In some of the posts, I've read that a JIG may not work on ICS based roms!!
Is this true?? Should I try a JIG first before I take the phone to Samsung Service??
I was on XXLSJ before the phone went dead!!
Click to expand...
Click to collapse
You are misinterpreting what you read. What you're referring to is resetting the binary counter, and no it doesn't work on ICS bootloader however it still works for putting device into download mode (unless its bricked).
nikufellow said:
3 100k resistors + 1k resistor in series connected between 4 and 5 pins of a male usb end when plugged will get you into download mode in case of soft bricks .
leap before you think
Click to expand...
Click to collapse
"Soft-brick" has absolutely no meaning, Your device is either "bricked" or it isnt. Its a made up term by n00bs when they cant get system to boot normally. Your devcie is only bricked when it wont power on or go into useable recovery+download modes. If you can simply use a jig or go directly into flashing a rom then your device is not bricked.
The "bricked" term is used far too loosely nowadays.
Pradeep said:
I had the same problem.. I could get into the download mode by:
1. Phone completely OFF state
2. Connect the USB cable to the phone and PC ( The battery charging indication has to come, atleast once )
3. Fire up ODIN
4. Get the phone into download mode ( Vol-down+home+Power ) while the phone is connected
5. The phone is now recognized by ODIN.
I could flash a kernel (tried siyah and Philz) but the phone was not booting.
While trying to flash Stock and XXLSJ, ODIN was getting failed at factoryfs.fs
After a few trys, the phone just went dead!!
Hope you can flash a firmware successfully :good:
Click to expand...
Click to collapse
Your phone died? you kiding ?
I'm using the leak version of Sammobile since 3 weeks... Why do you think the phone make a bad reaction now? why now?
Ok, you try to flash OFW and don't result. and then you flash again the XXLSJ ? and the phone colaspe?
What kind of roms do i flash? OFM or CFW ? ICS or JB ?
Well if a can connect with ODIN of course
A quick question!!
Is it possible that the phone can be revived (put into download mode) using a JIG if it is not starting at all for any key combinations and it is not showing charging animation when plugged into a computer or a power source??
Pradeep said:
A quick question!!
Is it possible that the phone can be revived (put into download mode) using a JIG if it is not starting at all for any key combinations and it is not showing charging animation when plugged into a computer or a power source??
Click to expand...
Click to collapse
Yes its possible which is the reason we already mentioned to try it
It all depends on the actual base issue though as to whether it will work. Its worth a try either way though, They only cost £1-2 or you can make them yourself if you have the spare parts. (Don't ask how, Use search).
I have tried the JIG, but no luck!!
I have given the phone to Samsung Service.
Hope they fix it!!
Will they use JTAG or it has to be done somewhere else in case Samsung people refuse to do it??
They wouldn't refuse just act dumb tell something like you were updating firmware via kies and all of a sudden power went down and device bribed
leap before you think
nikufellow said:
They wouldn't refuse just act dumb tell something like you were updating firmware via kies and all of a sudden power went down and device bribed
leap before you think
Click to expand...
Click to collapse
Thanks!! Well I did act dumb there!! Said I downloaded a game Royal Revolt (~200 MB), the phone got heated, blah blah blah......
Well I did not tell about firmware upgrade via kies and all....
Only thing that I can do now is wait and hope!!:laugh:
Hello,
Maybe you can shed light on my situation. I was using Resurrection's 4.2.1 ROM on my SGS2 and then some Google processes started to force close. So I went to recovery mode and tried to flash the same ROM over again, but it was not there. Stupidly I went to backup/restore and tried restoring the device. It said something about deleting boot load up (something among those words)? Then my phone just died. I could not turn on the power, recovery mode, download mode or even get the screen on when charging the battery. From my understanding, the processor is not fried, but it just can't boot up. My question to you experts is: Has anyone had a similar problem, and if so can a micro USB jig fix this issue or is this a job for MobileTechVideos and their JTAGing solution?
Hopefully someone has some information on this matter and can let me know what my options are.
Anyhow, I am going to the store early tomorrow to pick up the necessary items to make a USB jig. I will let you know if it works out too.
Thanks in advance. :good:
Jig wont work because of the updated bootloader. It only works with Gingerbread bootloader.
I'm afraid you only hope is give it to someone and let him try to repair the phone with Jtag.
still...try a jig. Can't hurt.
from sii xda-ded
boki9999 said:
Jig wont work because of the updated bootloader. It only works with Gingerbread bootloader.
I'm afraid you only hope is give it to someone and let him try to repair the phone with Jtag.
Click to expand...
Click to collapse
Wrong.
The USB jig works on all bootloaders for putting device into download mode. What doesnt work is resetting the binary counter on ICS+ bootloader.
Your confused or misinformed.
OK. I made a jig and tested it out with my friend's SGS2 and it worked. It put it into download mode no problem. But when I tried it on my phone, it didn't work. I think this phone is toast, or maybe I should send it in to JTAG it. :crying:
jtag it is. Good luck with that.
TheATHEiST said:
Wrong.
The USB jig works on all bootloaders for putting device into download mode. What doesnt work is resetting the binary counter on ICS+ bootloader.
Your confused or misinformed.
Click to expand...
Click to collapse
Thanks for the info.
Sorry on the misleading post! :/
I'm not sure my s3 bricked or not, yesterday i try to flash a new firmware MC3. But it was fail after, i was trying to flash older firmwares but it didn't work either. I can't turn on s3, it's also said "Please connect with KIES for recovery", i plugged it to computer but it doesn't seem connect with my computer. Please help, thanks so much.
hoangtung619 said:
I'm not sure my s3 bricked or not, yesterday i try to flash a new firmware MC3. But it was fail after, i was trying to flash older firmwares but it didn't work either. I can't turn on s3, it's also said "Please connect with KIES for recovery", i plugged it to computer but it doesn't seem connect with my computer. Please help, thanks so much.
Click to expand...
Click to collapse
Make sure you put your phone in download mode, and also Samsung USB Drivers installed on your PC. Try other USB cable if it did'nt work. Redownload the firmware, maybe it is a corrupted file
If you can boot into recovery then format data and cache, that might make the phone bootable again. If that doesn't help then boot into download mode as above and flash the correct stock rom via odin.
If it won't boot into download then you have a hard brick, service centre repair required.
fanbogo said:
Does anyone know how to run triangle away on SGS 3 without downloading additional data? The point is that I bricked my device, somehow lost IMEI and put phone into factory mode, wifi doesn't work, the same goes for mobile networking. I'd like to give it back to where I bought it from but in Odin mode you can see that the custom binary download is yes (10 counts). In other words I'd appreciate it if you told me what to do to return the device and get it fixed or replaced. Thank you.
Click to expand...
Click to collapse
Have you tried without downloading or used some other wifi .
Please stop hijacking other threads all the time .
jje
JJEgan said:
Have you tried without downloading or used some other wifi .
Please stop hijacking other threads all the time .
jje
Click to expand...
Click to collapse
sorry mate, I'm desperate. It can't be done without mobile networking or wi-fi because it claims it needs some additional data.
fanbogo said:
sorry mate, I'm desperate. It can't be done without mobile networking or wi-fi because it claims it needs some additional data.
Click to expand...
Click to collapse
Do not spam the forums, I have deleted your posts. Did it ever cross your mind that the best way to get an answer would be to create your own thread in the Q&A forum and give as much detail in there as you can? If it didn't cross your mind then I would suggest doing it.