Hey Guys,
I searched for my problem in many places, no go.
No one talking about Streak not going into Fastboot mode. Had to start this new thread.
---------------------------Here's what happened...---------------------------
I was trying to install GingerStreak 2.4.4 from GingerStreak 2.4.3.
DJ Steve's Thread
According to the instructions, I flashed
amss.mbn
and
dsp1.mbn
(got both the files from the first link above)
---------------------------Now the problem is...---------------------------
Then when I tried to reboot into Bootloader (Power+Vol Up+Vol Down) nothing happens apart from the Dell logo being displayed.
I try to boot normally, still stuck at the Dell logo. The phone never even reaches the boot animation.
I try to go boot into fastboot (power+camera key)mode, but the phone never even boots. The screen stays off, so do the LED lights.
---------------------------The problem I found out---------------------------
I figured out that the files downloaded above were incomplete(due to slow speed Chrome showed incomplete files as download complete).
amss downloaded: 111KB. Actual Size: 15.41MB
DSP1 Downloaded: 250KB. Actual Size: 8.94MB
So, I flashed the wrong files.
Now, I guess, the phone is bricked big time.
I need to get into fastboot mode (to flash the correct files) or anyhow get my phone working.
I also need to know if QDL tool will help me sort this out. It is currently downloading(again very slowly). If I get the answer, will post back.
Guys, need help. Please help me out to get this issue sorted out.
me also have same problem
supersophisticated said:
Hey Guys,
I searched for my problem in many places, no go.
No one talking about Streak not going into Fastboot mode. Had to start this new thread.
---------------------------Here's what happened...---------------------------
I was trying to install GingerStreak 2.4.4 from GingerStreak 2.4.3.
DJ Steve's Thread
According to the instructions, I flashed
amss.mbn
and
dsp1.mbn
(got both the files from the first link above)
---------------------------Now the problem is...---------------------------
Then when I tried to reboot into Bootloader (Power+Vol Up+Vol Down) nothing happens apart from the Dell logo being displayed.
I try to boot normally, still stuck at the Dell logo. The phone never even reaches the boot animation.
I try to go boot into fastboot (power+camera key)mode, but the phone never even boots. The screen stays off, so do the LED lights.
---------------------------The problem I found out---------------------------
I figured out that the files downloaded above were incomplete(due to slow speed Chrome showed incomplete files as download complete).
amss downloaded: 111KB. Actual Size: 15.41MB
DSP1 Downloaded: 250KB. Actual Size: 8.94MB
So, I flashed the wrong files.
Now, I guess, the phone is bricked big time.
I need to get into fastboot mode (to flash the correct files) or anyhow get my phone working.
I also need to know if QDL tool will help me sort this out. It is currently downloading(again very slowly). If I get the answer, will post back.
Guys, need help. Please help me out to get this issue sorted out.
Click to expand...
Click to collapse
pls help me out from this problem
Figured out and finally unbricked my Dell Streak
Yessss...... my phone is back!!!
Here's the solution.
Try this...
Go to this page...
RDTK.net
Look for QDL tool and streakflash.zip.
Firstly after the download, you have to get the drivers (guess the problem is only with Win7 64 bit OS) in place.
The same link above has the links on tutorials to install QDL tool drivers for Qualcomm HS-USB Diagnostics 9002.
After this...
1) Run streakflash version from the streakflash.zip(after extraction though).
2) Boot into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in streakflash QDL tool.
3) Hit the run button. The process should stop at success.
4) Disconnect USB cable and close streakflash QDL tool.
5) Now run the QDL tool that came in repairtool.zip (after extraction though).
6) Boot the Streak into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in QDL tool.
7) Hit the run button. The process should stop at success. If not, dont forget try again and again. Make sure you change USB ports (to which you are connecting ur streak) on ur system too.
This should definitely work. Mine worked like a magic.
As the page linked to says the tutorials and QDLTool versions are mirrored from streakdroid.com. I don't want anyone thinking I am taking credit for others work.
Glad you were able to "unbrick" your phone.
Totally Agree! Sorry I missed out that streakdroid part.
I appreciate your help.
I am thankfull to you, as I was facing same problem with my Streak5.
I am able to use it with DJ_Steve 2.4.4.
Regards.
Mahesh
maheshbhoir said:
I am thankfull to you, as I was facing same problem with my Streak5.
I am able to use it with DJ_Steve 2.4.4.
Regards.
Mahesh
Click to expand...
Click to collapse
Glad Mahesh!
It seems so obvious, but if my post helped, you have the thanks button right there.
.
Help me earn my first one.
supersophisticated said:
Glad Mahesh!
It seems so obvious, but if my post helped, you have the thanks button right there.
.
Help me earn my first one.
Click to expand...
Click to collapse
I just gave it to you, lol
thanks it fixed my streak
supersophisticated said:
Hey Guys,
I searched for my problem in many places, no go.
No one talking about Streak not going into Fastboot mode. Had to start this new thread.
---------------------------Here's what happened...---------------------------
I was trying to install GingerStreak 2.4.4 from GingerStreak 2.4.3.
DJ Steve's Thread
According to the instructions, I flashed
amss.mbn
and
dsp1.mbn
(got both the files from the first link above)
---------------------------Now the problem is...---------------------------
Then when I tried to reboot into Bootloader (Power+Vol Up+Vol Down) nothing happens apart from the Dell logo being displayed.
I try to boot normally, still stuck at the Dell logo. The phone never even reaches the boot animation.
I try to go boot into fastboot (power+camera key)mode, but the phone never even boots. The screen stays off, so do the LED lights.
---------------------------The problem I found out---------------------------
I figured out that the files downloaded above were incomplete(due to slow speed Chrome showed incomplete files as download complete).
amss downloaded: 111KB. Actual Size: 15.41MB
DSP1 Downloaded: 250KB. Actual Size: 8.94MB
So, I flashed the wrong files.
Now, I guess, the phone is bricked big time.
I need to get into fastboot mode (to flash the correct files) or anyhow get my phone working.
I also need to know if QDL tool will help me sort this out. It is currentlyi downloading(again very slowly). If I get the answer, will post back.
Guys, need help. Please help me out to get this issue sorted out.
Click to expand...
Click to collapse
but why you required to flash amss & dsp1 if you are upgrading , is it not only required when you are from 2.2 ?
babamanan said:
but why you required to flash amss & dsp1 if you are upgrading , is it not only required when you are from 2.2 ?
Click to expand...
Click to collapse
Use streakflash to repair it.Then flash the amss and dsp1 file again,because it is necessary for upgrading to 2.3.3.
babamanan said:
but why you required to flash amss & dsp1 if you are upgrading , is it not only required when you are from 2.2 ?
Click to expand...
Click to collapse
Exactly!
I wasn't supposed to flash those files. But since I was fed-up of many issues, I planned that I would go for a clean one starting from scratch.
The best way to install the amss.mbn and dsp1.mbn files is to flash the stock ROM that your custom ROM is based on.
supersophisticated said:
Yessss...... my phone is back!!!
Here's the solution.
Try this...
Firstly after the download, you have to get the drivers (guess the problem is only with Win7 64 bit OS) in place.
The same link above has the links on tutorials to install QDL tool drivers for Qualcomm HS-USB Diagnostics 9002.
After this...
1) Run streakflash version from the streakflash.zip(after extraction though).
2) Boot into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in streakflash QDL tool.
3) Hit the run button. The process should stop at success.
4) Disconnect USB cable and close streakflash QDL tool.
5) Now run the QDL tool that came in repairtool.zip (after extraction though).
6) Boot the Streak into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in QDL tool.
7) Hit the run button. The process should stop at success. If not, dont forget try again and again. Make sure you change USB ports (to which you are connecting ur streak) on ur system too.
This should definitely work. Mine worked like a magic.
Click to expand...
Click to collapse
Bro you are great. I have no words to say my thanks to you. By your way I fixed my mini5. thanks bro
Related
my Streak5 becomes a brick, after i try use fastboot -w, current sutiation is: can't power on with press power button, and no fastboot press power+crmera, no recovery press power+volUp+VolDown, and no device found once connect to Windows PC and press volUp. someone can help to recover it?
From the Dell Streak entry on the XDA Wiki:
WARNING ABOUT FASTBOOT: Do not attempt to use fastboot erase or fastboot -w on the Streak. The fastboot program on the streak has issues and attempting to erase partitions with it may result in it hanging. If it hangs the Streak will not be able to start up and is likely not rescuable by any manner (including QDL Tool). Use factory reset via recovery mode instead.
Click to expand...
Click to collapse
I wish I had more encouraging news for you, but I'm afraid you need to get a hold of Dell.
You didn't do any research before you tried to flash your Streak so now you pretty much have an unrecoverable brick. You may have some luck with JTAG but it's a 50/50 chance you won't be able to use SIM with it by what I have read in the forums. You can forget about warranty after what you've done to it. SO this is what happens when you flash without having read enough
download streakflash from streakdoid.com that will unbrick it but with base 2.2 drives so you cant go back to 1.6 after you use it, only 2.1 and up. so run streakflash then flash 2.1 or 2.2 recovery and intall update.pkg
Why did you bump a 3 month old thread? more importantly qdl tool will not work here by itself anyway.
You must dissemble the device to fix this specific issue.
My phone is not booting up.. What has happened to my cell phone.??
I did not do anything for this to occur It was actually ON. I had not restarted or even shut it down when i used it few mins back.. When i returned to it now it was showing the Boot screen, I had no idea of what to do. Just removed and re-inserted the battery.
Now the Phone gets stuck at this command as below !!
Fastboot mode started
udc_start()
--suspended --
What to do.? Please Help.
http://forum.xda-developers.com/showthread.php?t=1088046
I am using the OpenOptimus Rom 2.202.1 and clockworkmod recovery.
The Mobile was in charging state when this happened. It noticed it was in boot screen so i removed the charger and then removed the battery and restarted.
Now should i reflash usign KDZ or is it possible to revive my system back to normal without reflashing.??
clawsright said:
I am using the OpenOptimus Rom 2.202.1 and clockworkmod recovery.
The Mobile was in charging state when this happened. It noticed it was in boot screen so i removed the charger and then removed the battery and restarted.
Now should i reflash usign KDZ or is it possible to revive my system back to normal without reflashing.??
Click to expand...
Click to collapse
follow the link provided by sweetnsour u will get ur phn back to life
I followed the steps given on that thread
My pc shows new device found ANDROID. Device is not getting detected
But on this step in cmd
fastboot erase recovery
it shows < waiting for device >
i too got such problem.
while holding down back +Vol down connect your phone to pc .It will enter into emergency mode.Then your Computer might detect it.
Can anyone of u help me ???? My phone is still stuck with Fastboot mode
Basically on a windows machine you download kdz updater and uncompress it as it is a zip file.
Download from here.
This is what I did on an xp laptop.
I had to down load the drivers from the official lg site. when here you enter the code that is on the box the phone came in or under the battery.
Chose the your county and laguage from the drop down box at the top right of the dialogue box. Then from the middle you can choose the drivers. For some reason I had to find the files and click on them to install the driver.
Ok once you decompress kdz updater there are three seperate files to work with. 1. windows enabler. 2. msxml.msi 3.KDZ_FW_UPD.exe
You will also need to download the right file to restore with,You can find it with google.
Please check here the The_ERROR thread wich explains it very well:
[ROMS] Original LG Firmware list.
Install msxml now.
Now you have to boot the phone into rescue mode. On Lg Optimus One turn phone off even if it means taking out the battery.
Press power - volume up - back (this button is next to the home button).
Connect to usb now.Computer found new hardware and installed four drivers.
Then open device manager. Left click my computer - properties - device manager. You need to disable the lg modem driver. Left click on it and disable.
Now launch kdz updater. There will be a drop box on left set to 3gspt or similiar. on the right drop box set to diag. The long box just above the info box with a file at the side lets you browse to find restore file. e.g. V10a.00.kdz.
Double click the button below and let it do it's thing. Took 15min. My phone shut down and came up with an error at the last minute. Anyway I rebooted and all was good.
Everything was the way I left it. Just had to re-root.
My only real problem was getting the kdz installer to see the phone.
After installing the drivers restart pc. If it finishes quickly and just before saying finished it says phone not found try removing all phone related drivers including nokia pc suite and the lg suite and remove and reinstall the drivers.
Hope this is of some help to you.
Finally, Recovered my phone by flashing KDZ through Emergency mode.. No other method worked..
clawsright said:
Finally, Recovered my phone by flashing KDZ through Emergency mode.. No other method worked..
Click to expand...
Click to collapse
I told you. Nothing else would work.
royal.tarun said:
My only real problem was getting the kdz installer to see the phone.
Click to expand...
Click to collapse
I had the same worries coz my pc did not detect my device at all..
I was trying to get pass the Fastboot mode.. But in the cmd when i tried to erase and re-install recovery it said waiting for device.. Luckily and finally after many tries i could enter emergency mode. Only then the phone got detected but fastboot didnot work there.. The Only way out was to Do the KDZ flash. I flashed the indian GB V20b and did a hard reset now. Flashed recovery and for now have left it with the stock rom..
I wonder now this problem arises due to custom roms.
---------- Post added at 02:03 PM ---------- Previous post was at 01:59 PM ----------
Is the fastboot mode the so called "Brick-ing" of mobile device.?
clawsright said:
I had the same worries coz my pc did not detect my device at all..
I was trying to get pass the Fastboot mode.. But in the cmd when i tried to erase and re-install recovery it said waiting for device.. Luckily and finally after many tries i could enter emergency mode. Only then the phone got detected but fastboot didnot work there.. The Only way out was to Do the KDZ flash. I flashed the indian GB V20b and did a hard reset now. Flashed recovery and for now have left it with the stock rom..
I wonder now this problem arises due to custom roms.
Is the fastboot mode the so called "Brick-ing" of mobile device.?
Click to expand...
Click to collapse
this problem was cuz didn't perform the steps carefully.
This can called bricking but not fully . As it can be recovered.
Bricking is when your phone is as useless as a brick.
Hi there,
Is there any other method to access fastboot mode rather than pressing the camera botton n the power botten together??? coz i have not being able to access the fastboot mod by doing so...dell logo appears and says factory reset and reboots. Please help!!!!!
Have you been trying to install a rom on your phone then? I had a situation today going from MIUI back to O2 stock froyo rom, which always gives me grief. In the end, when the phone gets really messed up the best way back is to use the recovery tool (qdl tool), but this is one to use with caution. If your not sure what your doing, spend a bit if time reading posts here to make sure you get all the drivers installed correctly.
To my knowledge there is no other way to get fastboot working besides the camera key.
Sent from my Dell Streak using xda premium
Hey,
thanks for your suggestion, after this prob i have been trying to use qdl tool
but not being able to install the driver, please can u post the steps to install the driver. it would be hearty appreciated.
Win7 32 bit.
themask123 said:
Hey,
thanks for your suggestion, after this prob i have been trying to use qdl tool
but not being able to install the driver, please can u post the steps to install the driver. it would be hearty appreciated.
Win7 32 bit.
Click to expand...
Click to collapse
Here are some links I found helpful:
http://forum.pocketables.net/showpost.php?p=59264&postcount=2
I have also spotted this - which tells you how to install the qualcom drivers which QDL needs. You also need to install the ADB driver from Dell which you can download from here:
http://www.dell.com/support/drivers...ileFormats?DriverId=R291096&FileId=2731115717
And I have used this to get my streak back when repairtool failed:
http://forum.xda-developers.com/showpost.php?p=19544875&postcount=3
That will probably get you to fastboot again, from there you can use StreakMod to mount the sd card, copy the Update.pkg of choice ( I did O2's 319 Froyo) and then reboot into fastboot, flash the matching recovery to the update.pkg, then do the vol+ and vol- boot and choose option 2 - software update option. Then, if all is well, the rom will install then the installer does the low level install stuff and hey presto - one working streak!
Good luck with all this. Oh, and here is a link that is a complete life saver when your looking for all this stuff
http://mirror2.streakdroid.com/manii/
It has it all. Check out http://mirror2.streakdroid.com/manii/Tools/ which has the repairtool and streakflash zip's. Manii is a complete life saver for sure! There are all the ROM's and matching recoveries in here too - so its a one stop shop.
I hope you get it back. One thing I've found out the very scary way is that the streak is one tough device to brick - there always seems to be a way to get back - unless you do the fastboot wipe option - then it's game over. I hope you have not done that!!
Good luck!
try using driver from this link https://www.google.com.ph/url?sa=t&...wMsgpQ_PiAP-8KRWw&sig2=RYdtwQOsIk10srEObUdY7g
extract the rar file and navigate it once you are upgrading driver. you should see "qualcomm cdma technologies msm" under other devices on your device manager (assuming you are using win7 32bit)
here is the process.
1. device is off. press the volume up button and connect to the computer.
2. go to device manager look for other devices and see if there is qualcomm cdma technologies msm you should have to update it using the driver mentioned above.
3. once the driver were successfully installed you can now use the qdl tool.
chriscullen42 said:
Here are some links I found helpful:
http://forum.pocketables.net/showpost.php?p=59264&postcount=2
I have also spotted this - which tells you how to install the qualcom drivers which QDL needs. You also need to install the ADB driver from Dell which you can download from here:
http://www.dell.com/support/drivers...ileFormats?DriverId=R291096&FileId=2731115717
And I have used this to get my streak back when repairtool failed:
http://forum.xda-developers.com/showpost.php?p=19544875&postcount=3
That will probably get you to fastboot again, from there you can use StreakMod to mount the sd card, copy the Update.pkg of choice ( I did O2's 319 Froyo) and then reboot into fastboot, flash the matching recovery to the update.pkg, then do the vol+ and vol- boot and choose option 2 - software update option. Then, if all is well, the rom will install then the installer does the low level install stuff and hey presto - one working streak!
Good luck with all this. Oh, and here is a link that is a complete life saver when your looking for all this stuff
http://mirror2.streakdroid.com/manii/
It has it all. Check out http://mirror2.streakdroid.com/manii/Tools/ which has the repairtool and streakflash zip's. Manii is a complete life saver for sure! There are all the ROM's and matching recoveries in here too - so its a one stop shop.
I hope you get it back. One thing I've found out the very scary way is that the streak is one tough device to brick - there always seems to be a way to get back - unless you do the fastboot wipe option - then it's game over. I hope you have not done that!!
Good luck!
Click to expand...
Click to collapse
Thanks a lot my streak is up and running
Whoo Hoo! Great news! I am so please for you
I know the feeling of relief when it all starts to get back to normal again - I have ended up back on Dell's latest 2.2 rom (360) and it's been rock solid ever since. I have not found any rom to be better or more reliable.
angelerikz said:
try using driver from this link https://www.google.com.ph/url?sa=t&...wMsgpQ_PiAP-8KRWw&sig2=RYdtwQOsIk10srEObUdY7g
extract the rar file and navigate it once you are upgrading driver. you should see "qualcomm cdma technologies msm" under other devices on your device manager (assuming you are using win7 32bit)
here is the process.
1. device is off. press the volume up button and connect to the computer.
2. go to device manager look for other devices and see if there is qualcomm cdma technologies msm you should have to update it using the driver mentioned above.
3. once the driver were successfully installed you can now use the qdl tool.
Click to expand...
Click to collapse
You saved me !!! :good: Thank YOU!
themask123 said:
Hi there,
Is there any other method to access fastboot mode rather than pressing the camera botton n the power botten together??? coz i have not being able to access the fastboot mod by doing so...dell logo appears and says factory reset and reboots. Please help!!!!!
Click to expand...
Click to collapse
just one solution, streakflash. search this forum for streakflash.zip, and you must find the driver for safe mode option to your pc. the driver is from samsung. after you done connecting your DS to PC, run qdl tool, after done, fastboot mode, reflash, then recovery mode to reinstall rom.
what if?
chriscullen42 said:
Here are some links I found helpful:
http://forum.pocketables.net/showpost.php?p=59264&postcount=2
I have also spotted this - which tells you how to install the qualcom drivers which QDL needs. You also need to install the ADB driver from Dell which you can download from here:
http://www.dell.com/support/drivers...ileFormats?DriverId=R291096&FileId=2731115717
And I have used this to get my streak back when repairtool failed:
http://forum.xda-developers.com/showpost.php?p=19544875&postcount=3
That will probably get you to fastboot again, from there you can use StreakMod to mount the sd card, copy the Update.pkg of choice ( I did O2's 319 Froyo) and then reboot into fastboot, flash the matching recovery to the update.pkg, then do the vol+ and vol- boot and choose option 2 - software update option. Then, if all is well, the rom will install then the installer does the low level install stuff and hey presto - one working streak!
Good luck with all this. Oh, and here is a link that is a complete life saver when your looking for all this stuff
http://mirror2.streakdroid.com/manii/
It has it all. Check out http://mirror2.streakdroid.com/manii/Tools/ which has the repairtool and streakflash zip's. Manii is a complete life saver for sure! There are all the ROM's and matching recoveries in here too - so its a one stop shop.
I hope you get it back. One thing I've found out the very scary way is that the streak is one tough device to brick - there always seems to be a way to get back - unless you do the fastboot wipe option - then it's game over. I hope you have not done that!!
Good luck!
Click to expand...
Click to collapse
what happen if there is no fastboot on your phone...is there a way to put it back on?
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script to get into fastboot at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
So you solve it! :good:
:/
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
foreverman said:
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
Click to expand...
Click to collapse
Then try enter in lelus fastboot mode, ad then flash x-loader, uloader, boot.img and recovery.img from stock rom for your device type model. Then repeat steps 1 and 2
Where can I find the lelus script?
Sent from my Note II
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Then you need a Technician with a Octopus Box to repair your partition table...
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Can you boot into recovery? We now have a custom recovery for locked bootloaders (and CM roms). If you can get into recovery, I would try some adb commands to mount the partitions.
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
ciccillover said:
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
Click to expand...
Click to collapse
Your EMMC partition is wiped or fried... you really need a JTAG service or a Box like octopus because your L9 is Hard-bricked...
Thanks for your opinion. Yet, I still want to hear from others.
I'm running into more and more problems with the L9 as their me grows.
-Fastboot doesn't work under Windows 8.1 and 10, but under the now obsolete(for me) Windows 7, unlike my other devices, which are fine with Win 10.
-ADB seems to work, but requiring the device to be still able to boot.
-I always boot to recovery from within Android as long as the L9 ain't bricked. After a failed rom install, during which the sd card failed(could no longer write or be formatted afterwards, the last time stamps of files and folders were set during the failed install) I discovered a problem with TWRP(Artas182x's and Edwin's), which may have been present since a long time: Trying to invoke TWRP via keypress will brick the device!
So, if my P760 no longer boots, there's only download mode available, sort of the final line of defense.
-There's sort of a trick if even download mode fails: After a failed attempt unplug phone, force switch-off, if the phone is in brick state. Then switch on, force switch-off again, and only then attempt download mode again. And have patience while holding down the vol button, it might take up to 20 seconds for the phone to switch itself on into download mode. (A single forced powerdown will cause Fastboot NOT to work the next time)
But I'm absolutely clueless about the recovery issue, for now TWRP is semi-working, can only be accessed via Android, as long as the phone is fully working.
W/o Fastboot, I now have flashed stock rom several times and rooted it with Kingo rooter just to be able to run Flashify to install TWRP. If Flashify is the culprit for the TWRP issues, I could need a recommendation for a better working app.
ciccillover said:
Thanks for your opinion. Yet, I still want to hear from others.
Click to expand...
Click to collapse
Tried OMAP flasher ? It needs memory configuration file in order to work with our device
No, I didn't. I have sold the phone for spares.
Inviato dal mio LG-D855 utilizzando Tapatalk
I never needed the OMAP drivers and tools. As they are ancient, they will probably make even more problems with newer Windows versions.
I could by no means invoke Fastboot on this device with Windows 8.1 and 10, Seven worked. So you had to go for Download Mode instead to recover to stock rom, then root with the Kingo tool, then install TWRP via Rashr or Flashify, the most time consuming way to recover from the frequent bricks.
And the LG Flash Tool 2014 always needed several attempts to get the job done. The latest official recovery tool from LG works in D/L Mode, but will always download the rom image anew.
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
EFAYSAL said:
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
Click to expand...
Click to collapse
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
SubwayChamp said:
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
Click to expand...
Click to collapse
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
EFAYSAL said:
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
Click to expand...
Click to collapse
Ok, I guess that your device is actually in bootloop and don´t booting.
Tutorial that you followed has many steps and don´t need to do all this to just root device and it contains some files like lk.bin that you can´t be sure that should be for your device.
Some users use this file (lk.bin) of an unlocked device and think that flashng in other device then get unlock it but no need, your device can be unlock it just follow some commands in fastboot mode.
Now you can do the next;
Try to flash again your rom stock (I guess that you don´t have a backup), if for some reason your official tool doesn´t work then use only some images like boot, system and userdata with the scatter.txt to flash them through SP Flash Tool.
Here a link to TWRP https://youtu.be/6vj_BY6xJdA, you can root it with supersu v2.78 0r v2.82 and here some files that can be usefull too https://drive.google.com/uc?id=0BwJgeCYTpnEHNlg2VUlieHFTYVU&export=download
Update steps that you are following to can assist. What extension has your rom and if it is recogniced for SP Flash Tool. I didn´t ask you if you can enter to fastboot mode and if you can then you can know if your bootloader is unlocked typing fastboot oem info
Most info that you give and some screenie will help to understand better
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
EFAYSAL said:
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
Click to expand...
Click to collapse
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
SubwayChamp said:
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
Click to expand...
Click to collapse
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
EFAYSAL said:
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
Click to expand...
Click to collapse
I´m not sure if you are connecting correctly your device at right time and form to can flash it properly. Every device has more or less a specific way to do it. My last alcatel it was connected just with device power off and after to tap on download, but in other device Blu Dash was connected pressing just vol_up and my last mt6757 Bluboo had to press both vol up and down at time to connect to pc and after to tap on download option. To have sure that is well done increase volume in your pc, you will hear a first sound that is cause pc is recognicing but then you have to hear a second sound that is when SPFlashTool is recognicing device and you will see a red line in down side of the tool window, release button inmediately and let tool to work.
This is a good rom for your device according the author is optimized https://droid1311.blogspot.com/2017/08/alcatel-fl02-aka-flash-plus-2-via.html and this is the link directly if you have troubles with pop-up-adds https://drive.google.com/file/d/0BwAGh1drb91SeDZwV1VXbXpjQWM/view
Also you can try with other versions of SP Flash Tool, most stable maybe should be v5,1628 https://androidmtk.com/smart-phone-flash-tool leth me know how you go
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
SPFlashTool 5.1628:
I try all the way with and without pressing any button but no luck . And when it work finishing with error.
SPFlashTool 5.1628:
I try all the way to get that mode but nothing works. So I try to click download button then conect the phone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
EFAYSAL said:
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
I try all the way to get that mode but nothing works. So I try to click download button then conect the pkone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
Click to expand...
Click to collapse
There is a part that is not variable in the way to use this tool, ever you have to tap on download before to connect device and is recommendable too connect cable usb to pc (not yet to device); from here is when the button that you have to press can vary but like I said you before in my last mt6757 (a very similar to yours) works pressing both vol at same time to connect terminal cable to device and now you will see a red line (could be violet-ish)
Try before just flashing only preloader file to recreate some partitions and then do other flash for the other files.
Of course you have to be sure that all drivers are installed correctly cause this tool needs to put your device in download mode (a special level) and also keep it in this state so find VCOM drivers for Alcatel and adb/fastboot installer and try to uninstalling some older drivers that you don´t use and many times we keep in our pcs and for a short data transmission can helo that all the rom move it in same folder where SPFlashTool is allocated.
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
EFAYSAL said:
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
Click to expand...
Click to collapse
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
- In what android version are you, 6.0?
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
- Did you try to flash just preloader, only this file?
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
SubwayChamp said:
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
Click to expand...
Click to collapse
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
SubwayChamp said:
- In what android version are you, 6.0?
Click to expand...
Click to collapse
Yes, last time it was 6.0 before the root
SubwayChamp said:
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
Click to expand...
Click to collapse
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
SubwayChamp said:
- Did you try to flash just preloader, only this file?
Click to expand...
Click to collapse
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
SubwayChamp said:
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
Click to expand...
Click to collapse
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
EFAYSAL said:
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
Yes, last time it was 6.0 before the root
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
Click to expand...
Click to collapse
You need to try two different ways to flash files and restore your device.
First method: fastboot mode
You need to get device enter to fastboot in order to flash some files like system, boot and userdata, then there are two main methods to do it:
- Pressing pwr + vol down
- And I mentioned that sometimes work pressing both volume button + pwr and a menu have to appear to can select an option to enter to (fastboot mode), in some devices this method is not working but you have to try several times attempting to.
Second method: SPFlashTool
You have to ever press first of all Download box and connect terminal cable to pc and the buttons thhat you need to press at time to connec cable usb to your device may vary, sometimes vol down, sometimes both vol but never pwr button; if pc recognice then you have to release all buttone an let it pc continue the flash process.
If SPFlashTool recognice device first flash only preloader file and select now lk.bin too. Flash only these two files and after do again a new flash with the rest of the files, Why you need to do this? your partitions are corrupted and you need to restore them with these files in order to can flash all another files.
Before all of this charge your battery, if you have a cover removable then extract it some minutes and put it again.
Also I read that for this model it´s used this tool instead of SPFlash Tool https://androidmtk.com/download-sugar-mtk-sp-flash-tool (inside the zip you will find a password to start the tool) but I´m not sure what kind of rom it needs, you have to connect your device to begin the process, you will find in product models section in the tool this variant for your device "FL02"
Try first the other tool and then this and let me know how you go, mtk devices are almost unbrickeable so it´s just to find the appropriate way to return it to the life.
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
EFAYSAL said:
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
Click to expand...
Click to collapse
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
I understand that you tried with Sugar tool with no lucky.
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Is there some custom development, recovery, roms for your device?
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
SubwayChamp said:
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
Click to expand...
Click to collapse
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
SubwayChamp said:
I understand that you tried with Sugar tool with no lucky.
Click to expand...
Click to collapse
Yes. After recognizing it keeps trying to download data but no luck.
SubwayChamp said:
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Click to expand...
Click to collapse
I know it is disappointing!. I try this but no luck.
SubwayChamp said:
Is there some custom development, recovery, roms for your device?
Click to expand...
Click to collapse
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
SubwayChamp said:
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
Click to expand...
Click to collapse
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
EFAYSAL said:
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
Yes. After recognizing it keeps trying to download data but no luck.
I know it is disappointing!. I try this but no luck.
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
Click to expand...
Click to collapse
I´ll tell you some ideas with no any specific order that you can try or see if works.
Really very strange that display stays in black, you told me that flashing files through fastboot is working but doesn´t appear not even bootlogo, connect to pc as it is and see how pc recognices in devices manager and my pc if appears like a determined drive d/e/f so it looks that some bad flashing burn your kernel and this case is similar to when a Samsung device need to use jtag method to revive, if in your country no-one knows about Alcatel devices this could be a similar case to what I´m saying then it could be a clue for a technician. I tell you this cause many time ago when I flashed by error a Samsung s4 and only this method revived my device.
Try this, flash your stock recovery only through SPFlash tool and flash after through Alcatel Download tool your stock rom cause some firmwares need to detect stock recovery first to can flash other partitions.
At this stage don´t you have stock recovery, no? so you can try to format data cause sometimes when bootloader is altered then avoid to boot and formatting data can solve this.
If this recovery twrp is for your device you can try flashing through SPFlash tool, you have to put recovery.img and scatter-txt in a same folder. then if succesfull format data, system, wipe cache and dalvik and maybe later try to port some custom rom would be a way to solve this.
To flash any partition through fastboot this is the syntax, just follow one by one any of the files that are in your rom folder so just follow these, if some of then can´t be flashed don´t worry then it´s not flashable:
fastboot flash boot bot.img
fastboot flash cache cache.img
fastboot flash lk lk.bin
and so on till the end
...But after try this if you didn´t get boot to recovery and obviously you can´t delete data nor system then delete first the next partitions trough fastboot typing:
fastboot erase system
fastboot erase cache
fastboot erase userdata
fastboot erase boot
Try all this and let us see how it goes
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
EFAYSAL said:
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
View attachment 4518365
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
Click to expand...
Click to collapse
I see that Sugar tool detects your device like rooted and refuses to flash anything, compare imei number which is in the box, I hope that it couldn´t be changed.
Don´t tell me simply no luck, what it says in SPFlash tool when you tried to flash TWRP and I guess that you put scatter-txt and twrp renamed recovery.img simply in the same folder. Just to be clear, to can flash with this tool your device it has to be off not needed fastboot for this. (provide some screenie)
Other combination of keys to enter to fastboot to flash some partitions when something is missing is, try these three ways:
- Pressing only vol down and at same time connecting to charger (connect first one terminal of cable to your device and then to the charger)
- Pressing the three buttons till a menu appears (you must to release inmediately all)
- Pressing vol up + pwr till a menu appears (you must to release pwr button inmediately) then choose fastboot
In the post 4 I provided a link from Google Drive, in this zip there are 8 items;
- From the item 2 use this version of SP Flash tool, put the four files in a folder and flash them
- In the item 3 you will find some scripts for fastboot, maybe they´re working better and also you have here a subfolder with twrp image.
- And if you get sucessfully install twrp in the item 7 there is a backup with some files to restore from this recovery.
Try one by one and update the info, I hope that your motherboard is not damaged.