Hello.
I recently got a galaxy s2 that had been water damaged and wouldn't start.
I disassembled the phone and cleaned it thoroughly with isopropyl.
After putting the phone back together, everything works perfectly, except for the front camera and... whenever the phone goes into standby/ sleep mode for more than 5 seconds, the phone will not come back on and I have to replace the battery in order to turn the phone back on. This happens every time the phone goes to sleep mode for more than 5 seconds. If I turn the screen back on before 5 seconds have passed, the screen comes right back on.
However, if I have the charger attached to the phone, nothing wrong happens and the phone works perfectly (except for the front camera).
I would
A factory reset the phone .
B flash firmware to rule in a hardware problem .
jje
Thanks for the reply.
I have tried resetting the phone but that didn't solve it.
I also tried to update the firmware, but I'm not able to, because when the phone restarts during the flashing proccess, the phone just stays off and won't power back on. I then have to re-insert the battery to power up the phone again, but then the flashing proccess is interrupted.
By the way. I don't have any experience with rooting android phones and don't know of another way to flash the phone, other than throught the "KIES" software or through the update function on the phone itself.
I'm not sure if the phone is rooted or has a custom firmware, but when I press vol up + home button when powering on the phone, I am presented with a menu that says ODIN, so not sure if that means the phone is rooted or not.
I'm not sure if the phone is rooted or has a custom firmware, but when I press vol up + home button when powering on the phone, I am presented with a menu that says ODIN, so not sure if that means the phone is rooted or not.
Odd that and i would guess it is custom firmware .
Recovery factory reset is
Vol Up + Power + Home Button held down and released at splash screen
Download mode is Vol Down + Power + Home Button
Can you get to either of the above .
jje
Oleq83 said:
Thanks for the reply.
I have tried resetting the phone but that didn't solve it.
I also tried to update the firmware, but I'm not able to, because when the phone restarts during the flashing proccess, the phone just stays off and won't power back on. I then have to re-insert the battery to power up the phone again, but then the flashing proccess is interrupted.
By the way. I don't have any experience with rooting android phones and don't know of another way to flash the phone, other than throught the "KIES" software or through the update function on the phone itself.
I'm not sure if the phone is rooted or has a custom firmware, but when I press vol up + home button when powering on the phone, I am presented with a menu that says ODIN, so not sure if that means the phone is rooted or not.
Click to expand...
Click to collapse
You have a lot of information you need.
Odin is the utility used to flash firmwares/kernels/modems/etc to your phone. If that screen that says "Odin" says custom binary: no (or something similar) then it is LIKELY that it is not rooted, but you can root and reset this display with a few different techniques.
I've found Kies unreliable at best when attempting to update firmware, and have only used Odin. (since Kies never fully updated my firmware even once)
Read FAQs and stickies here.
Ok. Thanks for the help to both of you.
Tried to flash a stock firmware with the odin software, but after the phone powers off during the flashing proccess, it wont power back on.
So I have to re-insert the battery again, which interupts the flashing proccess.
So the water has propably done too much damage to the phone then and it's propably not a software fault.
I've ordered a new battery in case that is the cultprit, but if it's not, then I'll propably just sell the phone for spares.
At least the screen is in pretty good condition
Oleq83 said:
Ok. Thanks for the help to both of you.
Tried to flash a stock firmware with the odin software, but after the phone powers off during the flashing proccess, it wont power back on.
So I have to re-insert the battery again, which interupts the flashing proccess.
So the water has propably done too much damage to the phone then and it's propably not a software fault.
I've ordered a new battery in case that is the cultprit, but if it's not, then I'll propably just sell the phone for spares.
At least the screen is in pretty good condition
Click to expand...
Click to collapse
Don't forget to press thanks the guys who helped you
My galaxy s3 has been stuck in safe mode for two days now which is frustrating as only the stock apps can be used. I have tried different solutions, which I list below.
How it happened.
I was initially on 4.1.1 and when I woke up I saw a notification to upgrade to 4.1.2, after that it did its thing and rebooted into safe mode.
solutions tried
1. Reboot - didnt work
2. take out battery for few minutes and reboot - didnt work
3. boot into stock recovery to try to factory reset phone, Volume button not working so cant select other option apart from reboot. - didnt work
4. Download stock rom from samfirmware and flash using odin - didnt work
5. Flash CWM using odin, didnt factory reset and flashed custom rom (omega). It boots into safe mode as well
6. Downloaded stock ics firmware, flashed using odin . it boots but stuck on samsung logo.
I dont know what else to do. Although am thinking downgrade the bootloader to one meant for ICS the try to flash to ICS stock rom again, would try this later in the day.
p.s Ignore more signature I own a galaxy s3 as well.
Switch off your phone..
Press the power button..
Once you see the logo screen press and hold the left capacitive button..
Sent from my GT-I9300 using Tapatalk 2
zoot1 said:
Switch off your phone..
Press the power button..
Once you see the logo screen press and hold the left capacitive button..
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
I already did that....still stuck in safe boot.
alphaola said:
I already did that....still stuck in safe boot.
Click to expand...
Click to collapse
I think its:
Switch off your phone..
Press the back or cancel(left) button..
Once you see the logo screen press and hold the left capacitive button..
Hey,
I'm having the exact same issue with my note 2. Wondering if you found a solution.
Anybody can help with this? I am having the same issue
use search, asked and answered too many times
I did search..
I tried everything.
full wipe, cache, dalvik, factory reset and it keeps saying safe mode.
so please help
EDIT:
i just installed slim rom, and it keeps saying safe mode...
s3 safe mode
one way work for me..
1-turn off the phone
2- remove battery
3- short + and - in battery connector for few minute
4-insert battery and turn it on
alphaola said:
My galaxy s3 has been stuck in safe mode for two days now which is frustrating as only the stock apps can be used. I have tried different solutions, which I list below.
How it happened.
I was initially on 4.1.1 and when I woke up I saw a notification to upgrade to 4.1.2, after that it did its thing and rebooted into safe mode.
solutions tried
1. Reboot - didnt work
2. take out battery for few minutes and reboot - didnt work
3. boot into stock recovery to try to factory reset phone, Volume button not working so cant select other option apart from reboot. - didnt work
4. Download stock rom from samfirmware and flash using odin - didnt work
5. Flash CWM using odin, didnt factory reset and flashed custom rom (omega). It boots into safe mode as well
6. Downloaded stock ics firmware, flashed using odin . it boots but stuck on samsung logo.
I dont know what else to do. Although am thinking downgrade the bootloader to one meant for ICS the try to flash to ICS stock rom again, would try this later in the day.
p.s Ignore more signature I own a galaxy s3 as well.
Click to expand...
Click to collapse
It's Volume button work fine??
The problem has nothing to do with reboot. As you can see have already mentioned reboot as part of the solutions I tried.
My device is fine with ICS firmwares but has issues with Jellybean (stock and modded rom including CM10.1). Currently am running ICS on it as thats the only way the phone works properly.
I installed 4.0.4 (XAALF2) via Odin, but it got stuck on samsung logo. Then turned it off and flashed CWM to do factory reset as the volume key doesnt work on stock recovery. After that everything worked fine. I was able to update to the latest 4.0.4 via OTA.
The problem is hardware, so you might want to contact Samsung.
I found some information about "Safe Mode".
It seems that every Android phone has a safemode.
"On Samsung’s devices, almost all users will be able to access Safe Mode with by pressing and holding the menu button during start up. If it’s a capacitive menu key, make sure to release and press again each time the LED under the key comes back on. You don’t want to miss the catch for Safe Mode because the button released itself."
Here is the link where i get the information: http://www.tested.com/tech/android/...ds-safe-mode-to-save-a-phone-from-boot-loops/
You can try it this way, maybe it will work.
Good luck.
Ic3y83 said:
I found some information about "Safe Mode".
It seems that every Android phone has a safemode.
"On Samsung’s devices, almost all users will be able to access Safe Mode with by pressing and holding the menu button during start up. If it’s a capacitive menu key, make sure to release and press again each time the LED under the key comes back on. You don’t want to miss the catch for Safe Mode because the button released itself."
Here is the link where i get the information: http://www.tested.com/tech/android/...ds-safe-mode-to-save-a-phone-from-boot-loops/
You can try it this way, maybe it will work.
Good luck.
Click to expand...
Click to collapse
I think u missing the point, the phone works fine with 4.0.4 firrmwares, it only get stuck in safe mode when updated to Jellybean 4.1.1 and above. No amount of key combination, factory reset or even custom rom was able to fix the safe boot.
The best option is to send it back to samsung, its definitely hardware issue.
alphaola said:
I think u missing the point, the phone works fine with 4.0.4 firrmwares, it only get stuck in safe mode when updated to Jellybean 4.1.1 and above. No amount of key combination, factory reset or even custom rom was able to fix the safe boot.
The best option is to send it back to samsung, its definitely hardware issue.
Click to expand...
Click to collapse
I'am sorry for misunderstanding u. I think you could be right. Maybe it is a hardware issue.
Don't forget to "unroot" and reset the "flash counters".
Greetz.
alphaola said:
My galaxy s3 has been stuck in safe mode for two days now which is frustrating as only the stock apps can be used. I have tried different solutions, which I list below.
How it happened.
I was initially on 4.1.1 and when I woke up I saw a notification to upgrade to 4.1.2, after that it did its thing and rebooted into safe mode.
solutions tried
1. Reboot - didnt work
2. take out battery for few minutes and reboot - didnt work
3. boot into stock recovery to try to factory reset phone, Volume button not working so cant select other option apart from reboot. - didnt work
4. Download stock rom from samfirmware and flash using odin - didnt work
5. Flash CWM using odin, didnt factory reset and flashed custom rom (omega). It boots into safe mode as well
6. Downloaded stock ics firmware, flashed using odin . it boots but stuck on samsung logo.
I dont know what else to do. Although am thinking downgrade the bootloader to one meant for ICS the try to flash to ICS stock rom again, would try this later in the day.
p.s Ignore more signature I own a galaxy s3 as well.
Click to expand...
Click to collapse
i did a reboot and it removed the safe mode :good:
My personal experience, i overclocked my SGS3 with Boeffla kernel on ARHD then i got freeze screen and phone reebot into safe mode, I entered into recovery and reebot then everithing was fine again.
Safe mode occurs when something in the phone is not working properly , could be hardware or software, however, stuck on it is not a good signal.
my advice is to send the device to service.
Do not forget to reset flash counter via Triangle Away and flash stock factory firmware.
Good Luck! :good:
note 3 stuck in save mode window
This problem occurs after changing to a new simcard not already installed before in the device.
1. Power off the galaxy note 3.
2. Remove the micro simcard from the slot by sliding.
3. Power on the device without the simcard.
4. It will run in a normal mode, if so, this will actually diagnosed that there is a simcard defined by the administrator as default. In the security setting in setting menu and for protection against theft, the original simcard must be insert to unlock this choice of detection of any change in new simcard. New simcard is defined as strange and theft suspected.
I hope this make you reach some solution for your trouble.
S3 SAFE MODE issue
Plz help....
On my s3 i9300, its always on safe mode. Tried FACTORY DATA RESET. Still on safe mode. Other issue is that on power on and off, back LED turns on for few seconds. Also volume down not working. These issues started after s3 went on safe mode. Any sloution??
shoeb_v said:
Plz help....
On my s3 i9300, its always on safe mode. Tried FACTORY DATA RESET. Still on safe mode. Other issue is that on power on and off, back LED turns on for few seconds. Also volume down not working. These issues started after s3 went on safe mode. Any sloution??
Click to expand...
Click to collapse
Same issue here, it is hardware
I went through a lot of threads and not one had a solution. So I will post here what worked for me.
Customer came to my store with Galaxy S3 (SPH-L710T) that was stuck in safe mode. I tried everything on this thread, nothing worked. Luckily I had a older Galaxy S3 (SPH-L710) with a broken screen, so I switched over the motherboard from the customer's phone to the old one - I did connect the customer's original LCD to the motherboard since my old phone had its LCD broken. Powered it on, no safe mode.
So at this point I just transferred the volume buttons flex cable to the customer's phone. Powered it on, no safe mode again.
Hope it helps someone!
Hello,
I purchased a second hand Samsung S3 i9300 with a cracked gorilla glass, but the touch works perfectly. When the guy showed me the phone it was working perfectly. When he was going to give me the phone, he removed the battery to get his SIM card out and then put the battery back in. When the phone restarted it said Safe Mode in the bottom left corner. When I got home I started checking the phone a little better and started looking the internet to see how to get out of safe mode. I have tried everything I have found. I have restarted the phone, I have shut it off and turning it back on, I have removed the battery, SIM, SD card and reboot, nothing. One thing I should mention is that the Volume Up key works perfectly when I'm inside the OS, but when I go to Download Mode (to flash with Odin) I'm unable to Continue from the main screen (it asks me to press the Volume Up key to continue but the key is unresponsive). I have also tried recovery mode, but again, I need to hold the Volume Up key and I do, but the phone boots normally and is still in safe mode. Even a Factory Reset hasn't fixed my problem. The phone is running JB 4.3 and my first thought was that maybe the update was not made correctly by the previous owner, but I can't find a way to downgrade to 4.1 or 4.2 because of the issue with the Volume Up key outside the OS. Please Help!!!
You start by reading the faqs and guides .
This question posted multiple times Safe Mode .
http://forum.xda-developers.com/showpost.php?p=28315455&postcount=2
But judged by your problems you need a service repair .
Ok, i've searched all over the internet for the same problem and i couldn´t find anyone who've experienced this.
Where's what happened, my power button started to mal-function after my phone restarted. Now i cant lock or unlock the screen with it. The funny thing is that if I press it long enough it shows that [Shutdown/restart] menu. And if i keep pressing it it will soft reset the phone as usual.
I've already tried an app to se wich keys are being pressed to rule out the stuck key problem. The phone no longer recognizes the quick press of the key to lock/unlock, it only recognizes the long press of the power button.
Also today it refused to identify the charger and didn't charge at all, dunno if it as something to do with it.
My phone is the Wiko Wax, rooted, custom rom( Tesla 0.4.9a) android 4.4.4, with custom kernel as well.
I have already re-flashed everything, formated my phone and everything, but it doesn't seem to get fixed.
This started to happen after the phone restarted it self, without me doing anything to it
hi, I have a i9100G s2, which is operating normally, but does not turn off once more by power button,
but removing and reinserting the battery alone and then you start running properly (stock firmware) I tried to reset but nothing.
What can be?
I try to install new firmware with Odin?
To go into recovery mode or download must first hold down the appropriate keys and then insert the battery, otherwise it goes through
thank you
Retranslation
Hi, I have a G i9100, which works regularly, but if off will not light with power button, but by removing and reinserting the battery starts alone and then work properly (stock firmware)
I tried reset but nothing.
What can be?
I try new firmware with ODIN?
To go into recovery or download mode I have to first hold down the volume keys and then insert the battery, otherwise it goes
Thank you
I forgot how stock sgs rom look xd Do you got there buttons settings? If yes tick it again maybe then it will start triggering if no backup your staff and do factory reset and if it doesnt help just flash stock rom again. Maybe there are better ways but these should work too
Oh I forgot to ask... But your button works normally? As like turns off screen etc?
And work on your eng man it is important skill nowadays
Sent from my iPad using Tapatalk
... flash stock rom again .... but it doesn't work.
If charging, you start regularly.
Why???
News:
the button works if the phone is charging