This seems to be more of a software issue than a hardware issue. I'm thinking it might have something to do with the kernel as well but I'm not sure...
Anyway the touchscreen on my rooted Evo 3D with hboot 1.50 is acting up. Sometimes it completely freezes up, and other times when I try and press different parts of the screen, like the the app drawer it just doesn't register. When it freezes up it also affects the soft buttons at the bottom of the phone.
I've tried wiping it several times, and I've also tried this across several different roms, even nandroids, and it is still causing problems.
Any ideas on how to fix this?
Try calibrating your screen threw settings to see if that helps.
Locked & Loaded
""shooter on Deck""
laie1472 said:
Try calibrating your screen threw settings to see if that helps.
Locked & Loaded
""shooter on Deck""
Click to expand...
Click to collapse
I had that thought too but it still didn't work. I should also mention that the only way to "fix" the screen temporarily is to hit the power button and then hit it again to wake it back up. It usually does the trick... for a little bit. Also sometimes it just goes berserk and start pressing things without me even touching the screen
Are you running any kind of lockscreen program such as widgetlocker? I had similar problems when doing so, all issues stopped when I uninstalled.
ifly4vamerica said:
Are you running any kind of lockscreen program such as widgetlocker? I had similar problems when doing so, all issues stopped when I uninstalled.
Click to expand...
Click to collapse
I wish I was so I could fix it but I'm not.
Sorry man, was stabbin in the dark. good luck.
Think it's the Digitizer...
I have the same problem with an Evo3D hboot 1.5 also. It is rooted (ship s-on) I've had the phone for about 4 months, taken good care of it, and thus thought this bug was a software issue as well...
This is what I've tried:
-Factory Data Reset
-Restore Backup partition to original ROM
-Tried different ROMs (sense3.0, olympian xe, sicksense vX)
-Deleted and reformatted SD card
-Leaving SD card unmounted
It seems to be a popular issue, and after searching the CDMA Development forums I have found at least two other threads on the same topic here:
http://forum.xda-developers.com/showthread.php?t=1398048
http://forum.xda-developers.com/showthread.php?t=1383707
I don't have insurance, and rooting hboot1.5 is not reversible, for it is permanently recorded on the bootloader, so I'm assuming that my local Sprint representative will be of little help in the matter. From what I can find it would seem that our options are limited to:
A.) Replacing the Digitizer/LCD assembly. Looks like this runs between $70-$120. Here is a solid video on YouTube demonstrating how to remove and replace the Digitizer/LCD:
http://www.youtube.com/watch?v=suS34kNNuLo
B.) Replace the Digitizer only. From what I've gathered this is a risky maneuver which is best left to professionals with the *right* equipment, however is a much cheaper option, Digitizers are around $20.
I left a message with a local cell repair shop asking if they could replace the digitizer without a new LCD, and expect a response tomorrow probably.
Unless anybody has found an alternate cause/solution to this problem, which I would be eternally grateful for, looks like hardware replacement is the only solution.
2 questions one are you guys using screen protectors some of them will cause issues crazy ones from random clicking to unresponsive screen . Also are you using your phone out in the cold weather or really humid out ? A cold screen and hot hands will also wig it out.
I have a Zagg screen protector, which Radioshack carries for numerous phones; however it was installed when I bought the phone, four months ago, therefore I cannot imagine it would suddenly be the problem.
Also, the screen glitches at room temperature, at the most unfortunate times.
I just flashed Timat Kernels, with no results....
root3dnoob said:
I have a Zagg screen protector, which Radioshack carries for numerous phones; however it was installed when I bought the phone, four months ago, therefore I cannot imagine it would suddenly be the problem.
Also, the screen glitches at room temperature, at the most unfortunate times.
I just flashed Timat Kernels, with no results....
Click to expand...
Click to collapse
I have a zagg on mine I put on no issues for me. How do you carry your phone ? Do you tote it around in your back pocket? Just curious. Some folks have squished there phone sitting on them and messed up the screens. Not sayin you did that . Also folks carry in pocket on hot summer days and sweat gets inside the unit and messes with it.
Also is your phone brand new or a refurbished unit?
The phone is a new unit and I try to be conscious of high-moisture situations, so hopefully that is not to blame. If anything, excessive pressure may have been the cause, from a vacuum-sealed Drycase; but I'm hoping HTC's build quality would withstand such force, which should be minimal compared to being sat on.
Others are experiencing issues with the E3D digitizer, and I'm 90% sure my phone is not misbehaving from physical/moisture damage.
Is there a moisture damage indicator that can confirm/dismiss that theory?
Thanks for the suggestions
root3dnoob said:
The phone is a new unit and I try to be conscious of high-moisture situations, so hopefully that is not to blame. If anything, excessive pressure may have been the cause, from a vacuum-sealed Drycase; but I'm hoping HTC's build quality would withstand such force, which should be minimal compared to being sat on.
Others are experiencing issues with the E3D digitizer, and I'm 90% sure my phone is not misbehaving from physical/moisture damage.
Is there a moisture damage indicator that can confirm/dismiss that theory?
Thanks for the suggestions
Click to expand...
Click to collapse
Check the battery it has a sticker that will turn a solid color if it seen some water or high humidity. Also I think there is one inside the phone.
I have in the pass seen evo's that were refurbs or new units that were sat on the refurbs glass wasn't glued well and moisture got under the glass and screwed the screen up with random issues. New phones can have the same issues I guess if you really put pressure to it tho there sealed pretty well.
If the Digitizer was going bad from pressure your screen would have faint black lines going down it kinda like graph paper.
I have my phone in a trident kraken case it's been doing good so far.
After hours of research, countless nandroid wipes, and even a few ROMs, I have determined this to be a hardware issue! (at least in my case)
Much thanks to Landon4444 for providing a way to test for a lame digitizer
http://forum.xda-developers.com/showpost.php?p=20791773&postcount=40Here's how to check if this issue is result of a faulty/worn digitizer:
In the phone dial exactly *#*#3424#*#* to access the HTC diagnostic menu.
Choose line test from available options, screen will turn black.
Draw small test squiggle.
Hold phone by corners with fingers/thumbs (landscape).
Gently, twist phone torsional-ly. *GENTLY!*
In my case, certain slight torque creates a false contact in the upper-middle of my screen. Fortunately twisting slightly in the opposite direction HAS RESOLVED THE PROBLEM FOR NOW. (that was easy) However, I would not expect this tactic to work for long, and am looking into getting the digitizer replaced at the cell shop.
Evo 3d help guys!!
Okay so I just got a raise and an Evo 3D part of my boss's incentive package. (I know I have a great boss!!) but anyway its been less than a month and I haven't purchased any of the screen protector stuff or case. It is now 17 degrees in New York and I'll just drop the phone in my pocket while walking but yesterday at the beginning of a date the parking meter wouldn't take my money and upon trying to use my phone it started dialing it's own numbers and wouldn't let me enter any of the numbers for my code (to unlock). *Mind you my date kept telling me all night "Its a sign that you need the iphone" and I totally like the HTC 3D.I tried calibrating **BY THE WAY IT'S NOT ROOTED YETTT* but the only options your given is the GSensor Calibration. I've noticed that after I enter a warm area the phone starts working fine again. I've never had a smartphone and I think,upon finally getting one, that's it's totally ridiculous that the phone stops working because of the weather. At this point I think I have a faulty phone and am gonna return it to only get another 3D,but has anyone heard of this issue and if so how can I fix it. I mean like what if I had a car accident or an emergency and my "smartphone" starts acting up because of the weather???
Hey guys...I put this post up a few days ago and still haven't received a response. my timing to retunr the phone is running short so I NEED SOMEONE TO HELP PLEASE!!...Is this a normal circumstance that my phone is going through? if not I'll return it and get another one.
Its some grounding issue occuring due to maybe screen touching the main board. Its occurs on my phone very frequently and when normal occurs only if i press hard on screen
my phone also freezes up sometimes and goes crazy and it takes it some time for it to start working....
I ended up replacing the unit.it was faulty. Funny thing is I was trying to tell the guy the problem and when he grabbed it he saw it was broken.the problem worsened to the point the the phone was dialing on its own and going haywire.
Sent from my PG86100 using XDA
Related
Well, I have had the 3D since launch. After the first couple of days I started seeing phantom touches. After 1 week I started to notice this was getting far worse and that the display/digitizer was registering touches when nothing was near the device.
Called Sprint walked through a full wipe of the OS and reinstall. That was a no go and wasted nearly 2 hours of my time on the phone... However the Level 2 tech agreed that it appeared to be a failure of the device and advised that I return it to the Sprint store.
Got to sprint and showed them the video I had made of what the phone was doing. They also agreed that something was wrong with the phone and replaced it immediately.
Just in case I am not the only one that is having this problem I am uploading the video to youtube... I will share that link with you as soon as it is done uploading.
This is a video showing the issue using the "draw" application:
If you run into similar issues let me know!
I've seen some strange things happen but I figured it was the Otterbox Defender case or humidity here in Florida.
Will watch more closely now. Thanks for the report!
I've also been having strange issues, where touches are appearing out of nowhere. Had to turn off the pattern lock as a result, since I nearly got locked out of my device since it wouldn't register my pattern properly. It seems to 'reset' itself after a couple reboots, but starts acting up again at a later random time. Between the poor GPS performance and this issue, I'm starting to wonder if I upgraded from my Evo 4G a bit too early...
Same thing happens to mine while texting I would click a letter but it would click another one. It just did it once tho
never discount the existence of a true phantom pressing those screens ;p
I have heard of several people with the issue. Kinda makes me nervous. Already swapped 1 due to bad camera.
Sent from my PG86100 using Tapatalk
Same thing happens to my e3d
My touchscreen is having issues lately too. It'll work fine for several hours, then the screen will either be unresponsive or register phantom movements. Sometimes it won't register the lockpattern as I move my fingers, and other times it refuses to swipe left or right between screens. I've been trying to figure out if it's some kind of software or hardware issue, but no luck. I'd hate to return it(since it's my 2nd 3D) but if it continues for the rest of the week, it's going back. I made a video clip of it jumping screens randomly just in case the Sprint store ask any questions.
*update
I installed the paint program like OP did and had similar things happen on mine with the random lines and unresponsive screens. I guess I'll return tonight for 3D #3....
Mine just started doin the same thing lately, any of you have results yet? Did you turn in your phone or did they repair it? I really dont wanna go to the sprint store and turn mine in because i dont want a refurbished unit. 9/10 in the past when ive went through insurance, the phone they send me is broken as well and then it goes round and round. Sometimes my phone will just stop responding to touch, it will have phantom touches and/or on the htc_ime mod keyboard on compact qwerty; the ui, jk, m, . column up and down wont work at all. strange to say the least, never had this happen to any of my phones before.
My launch day EVO 3D is being replaced also due to this issue. She be back up and running with my new phone Wednesday.
Sent from my PG86100 using xda premium
Well mine developed this problem a few days ago.
The top inch or so of the screen and when I get this problem the touch sensitive buttons also dont work sometimes.
My problem and my question is that, I dont have insurance on the phone, I bought it on Amazon from a private party after my EVO 4G was stollen.
If I take it to Sprint can they just replace the digitizer, since this is a defect of the phone and would that even fix this problem?
If you don't have insurance on the phone then you need to go on ebay and search for evo 3d lcd digitizer housing. Yesterday, I paid $50 shipped from usa.
If you cant find a good listing then u can buy the lcd + digitizer (or just the digitizer) without housing. But it's hard work to do these two because those things are glued and painful to disassemble. It will definitely look jacked up after all your hard work. Just get it with the housing (front black plastic)
Here is a usa seller with what i'm talking about but he as no feedback so i didnt buy from him.
http://www.ebay.com/itm/HTC-EVO-3D-...ultDomain_0&hash=item1c20adc044#ht_2172wt_286
There is a hi res disassembly video on youtube.
I've been experiencing this issue lately as well. I've had this phone since the month it was released and it only started acting up as of a couple weeks ago. It started off as the touch screen not registering any touches, not even the capacitive buttons. Then this week it started it started doing the crazy phantom touch thing. In order to get it working, I simply shut off the screen then turn it back on again. It seems to happen less if I'm lighter on the screen. Thank gawd I'm not the only one experiencing this.
Sent from my PG86100 using XDA App
I called a sprint store and they told me that they would either replace the digitizer or the phone for a fee of 35 dollars, since I did not have insurance.
So, I took my phone in and they had another screen that was from another phone that had a different problem.
After they replaced it, he did not charge me
I was happy until I started to drive home and I was checking it some more and realized that the new screen also had the same digitizer problem.
I guess im headed back to Sprint tomorrow hopefully they give me another phone. and I will happily pay the 35 dollars.
Wow thats a real good deal. I never considered taking it for repair. I thought it must be cheaper to do it myself. I hope they can get you a working one. I'm sure they won't try to charge you for it when you go back.
I'm having trouble with my Evo as well, not sure if its the same issue or not.. for about the past week my notification bar will be intermittently unusable, I can't pull it down at all.. then sometimes it'll work. Unfortunately the times I've been near a sprint store it's working fine.. UGH. Also it's been giving me some random letters occasionally when texting, or the most aggravating is when it "clicks" the backspace button and that sticks and it erases whatever text I just wrote. Sounds like a similar issue.. I just wish mine was consistent, sometimes it works perfect.
Call me an idiot but whats the app that you were using!?
Edit:nvm found it haha
Well today i paid the 35 dollars and will be getting another phone
A really good app for testing screen problems is call "touch test"
http://www.appbrain.com/app/touch-test/org.hermit.touchtest
Mine seem to get worse when i had more then one finger on the screen. and it got really bad with just a little bit of preasure on the screen.
I'm having a similar problem but it is only with the capacitative soft keys.
I have problems from time to time. It gets so annoying on Swype because it will leave breaks while I'm Swyping and instead of one word I'll get like four weird words instead. Very cumbersome.
Sent from my PG86100 using Tapatalk
well i have an odd problem, one one section of my screen doesn't pick up touches, only the area where the "C" is on the keyboard...its annoying due to thats where the OK buttons are...
i can still navigate sense i can use the track ball..
anyone else have this issue, or something similar?
Try wiping back to factory if stock or reflash the rom if rooted?
I had a weird issue with the touch screen on condemned 18.3 where on the lockscreen trying to drawdown the slider and then draw the pattern, it would freak out and glitch and not follow my finger at all and take several tries to get the pattern correct.
I then wiped and flashed the latest 4.0 GSB and haven't had any issues since.
That's not quite a touch screen failure as yours is, but I thought it would help as an example as something gone wrong and how I was able to remedy it.
i've tried flashing a few different roms, went from cs18.3 to a 2.1 sense rom, back to the latest gsb. it appears its must be a problem with the digitizer...
really sucks, i have to wait to april to upgrade this phone...
might be on craigslist looking for a cheap droid 1...
Ah man, that's unfortunate. Probably wouldn't be worth it to try to replace the screen/digitizer either. Yeah, that's probably your best bet, looking to get another phone. That's how I got my Eris, from craigslist. Great way to go about doing so.
Good luck to ya.
I actually have the same problem and something leads me to believe that an update is causing this. I had it bad a few weeks ago (can't press C, V or X - though I can swipe to the keys sometimes) and then I got a few market updates for Handcent, SuperUser, and something else which then cleared it up for a few days. Then I got more updates and it's back to the failing keyboard!
I really don't know how to pin point it and I haven't done any resetting or testing yet, but I have like gut feeling something is wrong with the software, not the touchscreen since someone else is having this problem.
Mine has been failing little by little. Im now down to the top right corner, bottom left, and bottom middle not responding. It hard to even get the apps drawer to open. It all started with the letter C with me too. Just gets worse.
****, my whole qwerty row doesn't work, neither does the trackball. Upgraded to a SGS2, but I still tinker with the ol' eris.
mine moved, it started working fine for a few days, then just a smaller section to the left of C doesn't work, only really effects when i have an "OK" to press...but track ball still works and typing is so much easier now.
my wife thinks its because i dropped my phone that it started working again
I know this thread is a couple of months old, but...
There's an area on mine at the top right below the notification pull-down that appears to be dead. I'm thinking it's because I've dropped it about 10 times, but nothing looks wrong with the screen otherwise. I've thought about buying a replacement screen for about 15 bucks, but I'll be able to upgrade at the end of March, so I'm really just thinking about holding off (though if the new screen/digitizer worked, it'd make for a good mp3 player with the wifi script).
Digitizer is going bad. Same exact problem happened to mine. I replaced it myself and it works perfect. I found how to videos on youtube and bought a digitizer for about $37 online. Only took a half hour to tear apart and replace. On the difficulty level, I'd give it a 6 or 7.
MBL85 said:
Digitizer is going bad. Same exact problem happened to mine. I replaced it myself and it works perfect. I found how to videos on youtube and bought a digitizer for about $37 online. Only took a half hour to tear apart and replace. On the difficulty level, I'd give it a 6 or 7.
Click to expand...
Click to collapse
YMMV.
Someone gave me an Eris that had digitizer problems along the lower left side of the screen (in portrait orientation). I bought a replacement digitizer ($22 iirc), installed it, and it worked perfectly - for about the first 30 minutes. Then, the problem re-appeared in exactly the same location with the new digitizer.
Same behavior for a variety of stock or developer ROMs, so highly doubtful that it was a "software problem". Very very odd - the chip that does the capacitive sensing is on the flex circuit attached to the digitizer, so it gets replaced when you replace the digitizer; I suppose that the signals that come off the mini-connector between the digitizer assembly and the phone's mobo are only power, ground, and I2C signals.
But there you go; taken all those observations together, I'd suspect that I had a problem on the phone's motherboard which was thermally dependent.
Despite my (negative) experience, the odds are still in favor that a digitizer replacement will fix the problem; but there is an outside chance that it won't.
just sayin',
bftb0
So my bro's had an Atrix for a little over a year.
Some time back, it started exhibiting this behaviour where the whole screen would just become totally unresponsive.
Searching around, I see issues where people lose responsiveness with a fraction of their touch screen, or the entire screen starts spazzing out with all these presses and swipe actions the user did not enter...
...but his just seems to have these periods. He'll be stuck at the lock screen from anywhere between 1 minute and a whole day... I can usually get it to work with random rapidfire hardware commands... and when it works, it works completely for a certain amount of time.
Thing is, that's only temporary, and the touch-screen ends up going back to an unresponsive state.
Any clue what's going on, or how to resolve it?
What's the software is he currently on? Is the phone bootloader unlocked and/or rooted?
Sent from my ATRIX using the Premium XDA App
You know what's (not so) funny about this? All of the things that you think are causing this sound really complicated. Is my phone corrupt? hardware defective?? etc etc.
You know what I found it caused this behavior after numerous factory resets and weeks of research and tweaks to my phone?
The f-ing goddam screen protector.
Yep, that's right. The over-priced, highly (over)rated $20 iShields brand one. I know for a fact that was the cause, after I figured it out and started talking to other atrix owners (minus the liar fanboys that lurk in every forum saying "works fine for me derp!" whenever someone dares to suggest a product has flaws).
Problem immediately went away, forever. I've gone naked since May /11 without a single scratch. IMO screen protectors on gorilla glass is for people who wear a seat belt in a car wash. I'm not sure, but I suspect the problem happens when the screen protector starts to age, and/or when it gets really warm. I also suspect it's a problem with certain phones and the types of touchscreens on those phones not playing nice with screen protectors. Started happening on mine after just one month.
omnius1 said:
You know what's (not so) funny about this? All of the things that you think are causing this sound really complicated. Is my phone corrupt? hardware defective?? etc etc.
You know what I found it caused this behavior after numerous factory resets and weeks of research and tweaks to my phone?
The f-ing goddam screen protector.
Click to expand...
Click to collapse
That rant's nice and all, and I'mma let you finish... but there's no screen protector. He's been going bare gorilla all since he got it...
Voelker45 said:
What's the software is he currently on? Is the phone bootloader unlocked and/or rooted?
Click to expand...
Click to collapse
Just to offer some backstory, this started a couple months ago back when he just had the stock AT&T rom (2.3.X or 2.2.X I think? I can't recall clearly) During one of it's "working" periods (last week), I unlocked his bootloader and flashed it with CM9...
Probably won't mean much since the problem existed before I unlocked+CM9'ed it, but while it's not freaking out, I can give you some numbers:
• Model Number: MB860
• Android Version: 4.0.3
• Baseband Version: N_01.77.15P
• Kernel Version: [email protected] #47
• CyanogenMod Version: 9.0.0-RC0-olympus-KANG
omnius1 said:
The f-ing goddam screen protector.
Click to expand...
Click to collapse
Yeh, I have had this problem with screen protectors interfering with capacitive screens before, I am now using some really cheap protectors (5 for £3) and have had no such problems since and have a good bit of pocket money left .
TLRtheory said:
That rant's nice and all, and I'mma let you finish... but there's no screen protector. He's been going bare gorilla all since he got it...
Click to expand...
Click to collapse
ah ok in that case, I have nothing else, I'm only good for ranting. GL!
My touchscreen randomly does these freak outs and stops working:
Usually for me it is caused when the phone is really warm (like on the charger in the car) or when my hands are sweaty (also could just be the the phone is warm in this case as well)
Once it's done with its freak out, I turn off the screen (my power button still works) and clean off the screen with my shirt, wipe the sweat off my hands and turn it back on...everything is then fine.
Also, with my old phone (dell streak) if I kept the phone in my pocket with the screen facing towards my leg it would exhibit this behavior (probably again a case of the screen becoming really warm) but if I kept it screen out it was fine.
I have the same exact problem and have gone back to my Captivate because I couldn't figure it out.
Sent from my Touchpad using XDA
News on this? Here's my experience.
Any news on this, guys? I'm going insane. Here's my experience: I used to get these touchscreen-stops now and then but then they started getting more and more often. What I do to make them stop for a while is a clean restore, that is wiping boot, system, preinstall, cache, userdata with fastboot before installing a new ROM or restoring from backup. Whenever I do that, it comes back to life. If I flash a new ROM without all those wipes, it doesn't work. What sucks so bad is that, even though that fixes the problem, it's only temporary. It starts again after a few weeks. There is NO way this is hardware, and there's also NO way we can't find a solution for this!!!! Come on, guys!!! HELP US OUT, PLEASE!!!!!!!
Have you tried the raindrop fix? I was having similar problems and it worked for me.
Sent from my MB860 using xda premium
My screen has ghost fingers if my hands are even the slightest damp.
A buddy of mine had really bad touch screen issues and had to send back for warranty.
Sent from my MB860 using xda app-developers app
I'm having the same issue
I'm having the exact same issue. It sometimes works, sometimes doesn't. Anywhere from one minute to a whole day, everything you described exactly. No screen protector. I wiped it once and it worked temporarily, but it's back to the old sporadic unresponsiveness again.
I'm still not convinced that it isn't a hardware issue. I'm going to buy a T5 Torx Screwdriver and open her up and see if one of the connections is loose. Has anyone else done this?
I'll post tomorrow night with my results.
Here is a handy trick to determine if your digitizer it going out.
1. Find an appliance like a cable set top box, AV receiver or computer for example
2. Lay your phone face down in the warm air that emits from devices like this.
3. Leave it alone for about 10 to 15 minutes.
4.Pick your phone up and perform some finger swipe heavy tasks.
If you notice its a lot more sensitive like you remember when you first got it then you have a digitizer that is going bad. If nothing changes then its most likely software related.
Okay so I took it apart (removed the motherboard, disconnected the radio and 3 cables, then put everything back together. It's not fixed 100% but it's a lot more consistent than it was. youtube dot com/watch?v=kxuF_73YIIY
cjmillisock said:
Okay so I took it apart (removed the motherboard, disconnected the radio and 3 cables, then put everything back together. It's not fixed 100% but it's a lot more consistent than it was. youtube dot com/watch?v=kxuF_73YIIY
Click to expand...
Click to collapse
Could be the ribbon behind the digitizer, if its loose or moves it can kill all response to touch. You may have to replace your digitizer to fix this.
Sent from my MB860 using xda premium
I'm dying here
I opened it up like the video explained. Everything looked OK. I used a heat gun at 50 C to eliminate any trace of humidity and put back everything in its place. Then, I did a full wipe and a new ROM flash. STILL NOTHING!!! This phone is a little over a year old! This is not possible :crying: Any new ideas???? THANKS!!!!
pichualvarez said:
I opened it up like the video explained. Everything looked OK. I used a heat gun at 50 C to eliminate any trace of humidity and put back everything in its place. Then, I did a full wipe and a new ROM flash. STILL NOTHING!!! This phone is a little over a year old! This is not possible :crying: Any new ideas???? THANKS!!!!
Click to expand...
Click to collapse
I would also suspect the digitizer. I replaced mine for $45 (frame pre attached attached highly recommended).
The connections are very small, so there is much that can go wrong while doing this kind of brain surgery and the ribbons will rip easily.
Sent from my MB860 using Tapatalk 2
Same problem here. It is like some Ghost is operating it without my permission
Sometimes feels like is should hit the phone on the wall.
I know its not gonna help.
Anybody there who has solution for this
I am having some major problems with my touchscreen/digitizer.
About three months ago I dropped the phone and it cracked the screen in a few places. It was still completely usable.
In the last month, there have been some areas of the screen that have become completely unresponsive. I could usually get around this by rotating the phone, touching a different area, and then rotating it back. However the problem seems to be getting worse where larger and larger areas are unresponsive. There is now a rectangular band about one centimeter high that goes the complete width of the screen that doesn't respond to any touch, ever.
In addition to the completely dead zones on my screen, the touchscreen sometimes becomes completely unresponsive which can be fixed by locking and unlocking the screen.
I don't have a lot of money for a new phone, so I was able to live with these problems, but they're getting worse. Also, if my wife or anyone needs to borrow my phone they often find it completely unusable. In the middle of me explaining the problems and workarounds, they usually just give up.
I'm wondering if I replace the digitizer, will this problem go away? Or is there something else wrong with the phone that might not be serviceable by me? In addition to the digitizer problem, my headphone jack stopped working. If I plug anything in, nothing happens and sound continues to come out of the phone speaker. That's leading me to believe the phone has some deeper problems that I might not be able to fix, but if I can fix the screen I can live with the headphone jack problem.
My digitizer wasn't cracked, but I have the same problem. I send my phone to service and I'm waiting for response.
"Service" is not an option for me. The warranty is gone. I do not have insurance. I purchased the phone refurbished for $50. The only reason I did not replace the digitizer the moment it cracked is because the digitizer is the same price as what I paid for the phone in the first place.
Mine under warranty so I send it to motorola service centre and they replace the digitizer for me. I get it back in 2 days after sending it in.
But they flash my ROM and I'm not sure whether my phone still unlockable or not.
Btw, I have read a lot of atrix user with digitizer issue. It send common for our phone. You can easily spot few threads showing you how to replace the digitizer.
Sent from my MB860 using xda app-developers app
Soooo, I hate to bring back a dead thread, but I figured it was better than starting one of my own.
My Atrix recently had a sudden impact of its own. Cosmetically, it is still perfect. The touchscreen no longer responds though.
Phone still works. It receives calls, text, syncs with email, changes volume, etc. The touchscreen just wont respond to any of my fingers lol.
My question to Ovitz (or anyone else) is, did you get your phone back fixed and what was the solution?
I am leaning towards the digitizer, but I just want to verify before I put money into it. There are no rattles in the phone. No crack at all. I, generally, take great care of my phones and this one looks basically like it did out of the box.
Thanks in advance!!!
§
You dislodged the connection for the didgitizer or broke. I suggest you replace it. There have been plenty of Q and A threads on this. Get one from eBay oem, YouTube search a how to, and take it slow.
Sent from my SAMSUNG-SGH-I317 using Tapatalk 2
hey guys.
I gifted my mom my Evo 3D a bit over a month ago. It was in perfect condition after a year of use. she says she hasn't sat on it. no screen cracks, no indications of any physical abuse.
we first thought it was the keyboard. and she had been telling me of so many issues she was having. so I updated her to freeza's 5.5 rom, sense 3.6 version (how come I didn't see any JB roms?! I've been on JB for a while...).
same thing kept happening. i started looking into it. turned on the pointer touches thing in developer options...turns out, the screen keeps pressing itself exactly in the middle horizontally, and about 85% of the way down vertically.
sometimes it keeps pressing so when it's a keyboard up, it presses the letter v continuously. but it presses everywhere. so it makes phone calls, selects things in market, selects in root explorer, etc. sometimes it gets "stuck" on pressing down, so nothing else works. you can see the pointer is stuck as if it was being pressed.
in TWRP i couldn't select the last item in the list (the one i was trying to flash!) but all other "lines" could be selected.
there are other issues (since we're on MetroPCS) but I can figure that out after the screen issue. since it happens across roms and in TWRP, I'm fairly confident this is not a software issue?
what can I do? is replacing the digitizer a sound idea? how much would that run me? how difficult is it to do? i'm trying to wonder if it's just a better idea for her to get a new phone....
any help with this is highly welcome. this is WEIRD!
id say the digitalizer. around 80,-, google. since you flashed another rom, it's highly unlikely its software..
Mine also does that. Rarely though. I thought it was because of protective film. Turning screen off and on fixes this.
I also have the same problem when typing with wet fingers.
Sent from my Evo 3D GSM using xda app-developers app
Your digitizers are dying
My advice is to keep a stuck ruu in your phone's sdcard in case of scenerios like this one because we all know that sprint techs may not even touch the phone if they discover your rooted and s-off. So, getting back on stock with "locked" bootloader is your next move. Thankfully that procedure doesn't involve using the touchscreen.
Take off any screen protectors, and make sure you are using the default HTC lock screen - HTC hard coded the calibration for the screen into the lock screen. If still problems, then yeah, you need the digitiEr
Sent from my PG86100 using Tapatalk 2
Jsparta26 said:
My advice is to keep a stuck ruu in your phone's sdcard in case of scenerios like this one because we all know that sprint techs may not even touch the phone if they discover your rooted and s-off. So, getting back on stock with "locked" bootloader is your next move. Thankfully that procedure doesn't involve using the touchscreen.
Click to expand...
Click to collapse
you missed the boat there. i'm on MetroPCS and so is that Evo 3D...not to mention this phone is 1.5 years old and has had its warranty voided multiple times
danaff37 said:
Take off any screen protectors, and make sure you are using the default HTC lock screen - HTC hard coded the calibration for the screen into the lock screen. If still problems, then yeah, you need the digitiEr
Sent from my PG86100 using Tapatalk 2
Click to expand...
Click to collapse
that was my first thought. to remove the old screen protector. but no, it's definitely messed up
no problems. the same store I bought that phone from and my other Evo 3D and the two Galaxy S3s from does repairs and they replace the lcd and the digitizer for $80. i've dealt with them for years now so I trust them.
Max_Pain said:
you missed the boat there. i'm on MetroPCS and so is that Evo 3D...not to mention this phone is 1.5 years old and has had its warranty voided multiple times
that was my first thought. to remove the old screen protector. but no, it's definitely messed up
no problems. the same store I bought that phone from and my other Evo 3D and the two Galaxy S3s from does repairs and they replace the lcd and the digitizer for $80. i've dealt with them for years now so I trust them.
Click to expand...
Click to collapse
Uhm... the digitizer for our phone costs about $10 or so... and from what you said your LCD is just fine... so I really wouldn't trust a store that's offering a $10 fix for $80... so bottom line just check if they can just replace the digitizer as it's the exact same procedure...
well looking online it looked like the whole thing was $60-100. on this thread i was told about $80.
that's not the issue though, problem is putting it together. I watched the video of the step by step, and there's way too many ways I can mess it up, and then my mom is out of a phone, instead of spending $80 for guaranteed work.
On my iphone I had a dead spot in the middle where you could see the digitizer was discolored if you looked at it at an angle.
I had a screen protector(or clear plastic, etc) placed between the LCD glass and the digitizer and it fixed the problem.
I guess it kept even pressure between the glass and the digitizer.
Worth a try if you don't mind experimenting but YMMV.
Don't risk it if you aren't confident though... I did it to my iphone because I hated it, lol.
Good luck.
well this is weird.
i'm supposed to take the phone to be repaired tomorrow morning (Thursday) so I decided to beforehand update everything on her phone.
I did a superwipe, installed the latest TWRP, flashed the ICS firmware, including Hboot 1.58 (i'm still S-OFF, thank goodness), flashed Cool ICS 12a...
and the phone is behaving like new. no screen pressing, no difficulty typing, over the last two hours of setting it up for my mom...it's as if it was brand new.
so now i'm wondering if somehow it got fixed and we can save ourselves the expense, or if this is a temporary fix and it'll go back to messing up...
I'm GSM, rom is without sense. But sense rom had the same issue.
Is it possible to calibrate screen without sense?
Sent from my Evo 3D GSM using xda app-developers app
I found this
Hey guys I just found this http://forum.xda-developers.com/showthread.php?t=1401365
I haven't tried it yet but it might work.