Related
I'm searching for a metal case for my new hermes. Anybody found one yet?
I tried it on ebay, but there are aluminium cases for wizard only.
signal killer
May I suggest that you don't buy a metal case for your Hermes. I am a long time Wizard owner (looking to buy a Hermes as soon as I can). I have had an aluminum case and always wondered what was killing my signal. If you do a search over in the Wizard forums you will see that those cases just kill your signal. Maybe the Hermes has some improvements, but I would be careful. Just thought I would save you from some frustration (and maybe some wasted money!) It's a shame, cause I love those cases as well.
Anyone found an aluminum case that would work yet? I have always hated leather cases never used an aluminum one, I just know I am gonna tear the screen up if I dont have something hard rotecting it while its in my pocket, basically I would be usin it in a manner like somebody would a sunglasses case, take it out when its in use, and put it back when its not..etc, and I'm not that important, if I miss a call due to bad signal, its no biggie.
Indeed. Aluminium does a good job of absorbing radiation. Sadly GSM is affected by it as well.
Well I haven't seen that at all with the Vario I get the same signal wether I have the case or not
Really? Vario was... a.... Wizard, was it?
Aye
You can find aluminium cases (silver or black) for the TyTN at www.pdair.com
i just received my PDAir aluminium case, it makes the device looks thicker. but at least u wont have to worry about cracking the LCD screen!
my previous ipaq pda and verizon vx6600 got LCD screen cracked due to sitting on it. i dont like to wear it on the belt, i like to put the pdaPhone in the pocket
I just received my aluminium case too. Here is a little information and some pictures I can provide.
http://www.wretch.cc/blog/doomer&article_id=4597663
I'd be very interested in any subjective assesments of the impact on signal strength, and battery life, as a result of using one of these cases.
I'd like one, but not if it significantly hampers the signal, or substantially drains the battery as a result of a need to run at higher transmission strength.
Until now ( exceed 12 hrs ), I didn't find any signal reduction. I have no problems calling out and accepting incoming calls while my hermes still wearing alumium case all the time.
I got mine PDAir case a couple of days ago. No reall problems really. nicely made, looks good (black one), and the belt clip is pretty good. Only one droped call, but I had one or two droped calls from home without the case, so I don't think it is the case. Overall I would recommend it.
If I get time over the weekend, I might post some hi rez photos of the black case with the Orange SPV 3100.
Ordered and received the black version from PDAir, I had ordered the invisible shield first, so my TyTN fit a bit too tight in the aluminum case cause of the shield..but it went in.
I am currently using this sucker so much that I really didn't like to have to flip the case open all the time to use it, I debated on removing the plastic window from the case, but just opted to throw it on the shelf within the first 15 minutes of opening the package.
I didt use it long enough to notice battery drain, but the signal strength was the same with or without the case, also the case hinges on the right hand side to allow it to remain in the case while using the keyboard..but it feels a bit weird, almost like its designed for a left handed person...hard to explain.
Well, I have had mine for about a week and I will say this,... THANK GOD! as I have dropped it since I've had the case and well,... IT WORKS!!!
I can get to all of the buttons AND even the antenna, it also ascut out for my lanyard that I use. Everything is accessable including the microSD card (why I don't know). It is a little difficult to get to some of the buttons with my big "sausage" fingers but it still serves the purpose that I need.
Unless I find a better case (which I haven't seen plans for) I sticking with this one.
PDAIR Great job!
I dropped my Tytn off the couch a few times after passin out while hangin out on IRC, the invisible shield worked very well...but I decided I would give the aluminum case another go..I removed the clear window and then thought the black case looked crappy around the silver phone, so I started to sand it down to polish it, I got all of the front cover sanded and part of the back, and went to see how it looked around the phone...I just held the phone and positioned the top cover over it, and then I noticed the screen flicker...I'm not sure if I missed this before I sanded it, because then I checked with different wallpapers and its not really noticeable with some and it only happens when the case is over it...kinda strange I thought, considering the phone has an aluminum bezel already around the screen from the factory, and I also did notice I would drop a bar on the signal if I wasn't in a strong area.
As many people making aftermarket stuff out of carbon fiber nowdays...I can't believe someone hasn't started making them for phone's/pda's
Its relatively cheap, and a lazy route of making them could be done by just vacuum forming one from an already made aluminum case.
What about Bluetooth? Does aluminium case shields it signal?
Got a black aluminium case from Boxwave. Looks and fits fine. Didn't notice any Bluetooth signal degradation so far.
BTW PDAir and Boxwave cases look identical - most likely both have the same OEM producer.
Got my aluminum case from dealone.com
Had my case since day two with my Cingy 8525. No problems noted, glad I have extra protection as I'm always bumping into things walking. Tables, chairs, etc. Mine is the monaco aluminum case in black. Absolutely love it!
http://www.amazon.com/Cingular-8525...s_sr_2/002-9456356-4411227?ie=UTF8&s=wireless
Just order 1 from there.
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Thanks for the review! I bought the same case a few months ago, although it was advertised as for the Verizon Touch Pro 2. I was unaware they made one for the Tilt 2. Now I won't have to worry about it falling off randomly!
thsi case probably wouldnt work with invisible shield on too huh
Doinshots said:
This is my first review, so I hope it doesn't suck.
Both my wife and I have the Tilt 2. I decided to go with InvisibleShield while she wanted a case. After looking at all the comments here about cases not fitting, I decided to go with 2 different ones from Amazon. One fit horribly, so i wont even mention it.
She is using the Tilt2 Praetorian Slip and she loves it. Installation was a little tough as the fit is pretty precise. I suggest installing the top (screen) side first and then the bottom (keyboard). Install both with the KB extended. I have attached pics of the fit.
The only complaint I have (she thinks of it as a feature) is that the cover makes it a little more difficult to slide out the keyboard. She like it because it used to slide open in her purse (mostly because of the fact that she keeps it in an inside pocket of her purse which causes it to hit just right against crap she has in another pocket). Overall, this is a pretty nice cover. I am sure you can get it cheaper than amazon, but I had gift certificates to spend
Hope this helps!
Click to expand...
Click to collapse
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
JJHiemenz said:
Neat.. glad yours fit. I ordered one for the Tilt2 from Amazon as well, and Boxwave sent one labeled 'Touch Pro 2'. I see yours doesn't have a cutout area for the PTT button either, do you have issues with that? My praetorian case would almost always trigger the PTT button whenever I handled the phone.
The top/screen portion of my Praetorian didn't fit right and opening and closing the top was almost impossible - even ended up ripping off the protective plastic along one side of the keyboard. (the protective plastic that is designed to be there, not the temporary stuff it whipped with) I can see just by looking at your pictures that your screen portion fits waay better than mine did.
When I contacted Boxwave about the issues, no questions asked and they sent a postage paid label for the return. I'd love to try this case again, as I did like the feel of it, but nervous about another no-fit. I went with BodyGuardz instead.. not sure I'm happy with those..
Click to expand...
Click to collapse
Man, sorry you had so many issues. The PTT button is indeed covered, but she has had no issues with it at all (hers is remapped to toggle bluetooth on and off). The fit on the screen portion is *very* tight. Took some effort to get it installed properly.
Also, mine definitely said "Tilt 2" on the packaging.
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
sleze said:
It is disappointing that it covers the PTT button. I assume your wife has abandoned that function (easily switching BT on/off)?
Click to expand...
Click to collapse
Nope, the PTT button still works perfectly under the cover. Does not get accidentally pressed and is responsive when you push it.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
Sounds like skinning/shielding your phone with GadgetShieldz might be the way to go. The GadgetShieldz does take a little time to install but it works. The protective film on the screen is easy to install and bubble free. It makes the phone non-slippery. It would not protect the phone like a case but it does prevent scratches. When installed, it adds very little weight and dimension to the phone.
Actually, there are other protective films/shields but I only have experience with GadgetShieldZ. It might work for you.
Boxwave Praetorian Crystal Slip for Tilt 2
orb3000 said:
Thanks,
I´ll include it on the main thread
http://forum.xda-developers.com/showthread.php?t=524059
Click to expand...
Click to collapse
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
azwildcat98 said:
Thanks for posting reviews on this case -- I'm trying to decide what route to take to give my new Tilt 2 some added protection, and more importantly, cut down on the slickness/smudge magnet-ness of the shiny battery cover (which is my #1 gripe with the GSM TP2, both CDMA versions have rubberized covers which won't fit their GSM siblings due to the placement of the 3.5 mm jack).
I really wish someone made a rubberized battery cover to replace the shiny OEM one. These snap on type cases are okay, but they become a major pain as soon as you need to pop off the battery cover in order to flash a new ROM (as I do often), reset the device, or swap out memory cards. I worry trying to snap-in and pry off these cases frequently will damage the phone -- especially when it's a super snug fit. IMHO, a rubberized battery cover, along with perhaps the upper portion of this case to protect the chrome bezel from getting nicked would be an ideal solution! I may just go down to Home Depot this weekend and see if they have a spray that can rubberize plastic, then I might just buy a spare OEM battery cover and see if I can rubberize it.
Click to expand...
Click to collapse
I wish I'd seen your post sooner! Home Depot and Lowe's does indeed have something like that. I'm sure lots of hardware stores do. It's called Plasti-Dip. I have a can right here You can buy it as spray-on or dip/brush-on applications. I use it on mountain bike parts and tools for extra grip. I'm not positive how well it will stick to a slick plastic surface but it is an option.
BluEyedTiger said:
Just to report on this, I got one of these in the mail yesterday. So far I love it. It wasn't terribly difficult to get on. It fits very well too. My only real complaint is that it doesn't accommodate the PTT button that the Tilt 2 has right next to the volume buttons. It's not a big issue since I don't use PTT and the case doesn't prohibit using the key anyway.
Just be careful and make sure you order the one that specifically says it's for the Tilt 2. They make other models. I know they have the Praetorian on eBay but to be safe I opted to get mine directly from Boxwave. I got what I ordered too and could have used they're return policy if I needed.
Oh...I'll be happy to post pics if anyone wants but I think someone already put some up of this one a Tilt2.
Click to expand...
Click to collapse
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
BehindTheLight said:
Hey man, I'm thinking about ordering this case and I wanted to see if you still like it and how it has held up over the past month. Thanks.
Click to expand...
Click to collapse
It's held up quiet nice...even with as much flashing I do (have to remove the bottom piece every time). I've figured out a great way to put it back on that's really fast and easy. Some people say it's difficult to get on. I think the top piece is the hard part but I've taken it off a few times and have no issues there either. It still fits good. If I remember, next time I take it off I'll shoot some pics of how I put it on and upload them.
Learic said:
I ordered one from BoxWave and I think I'm still going to shop around for something else. It seems like the Tilt2 has less options than the other variations of the Rhodium so people may just be settling for this due to "Slim Pickin's."
I like the way the gel gives more texture and grip to the phone, but I still feel uneasy because it's definitely not a snug fit. The part that covers the screen section of the phone is very flimsy and after you get it on, you want to keep checking it to make sure that it is attached; it feels like it can easily slip off at any time. This is specifically evident when you slide your screen up and tilt it. Tap the top right, or the middle section that really has no grip around the phone, and it might just pop off...
I still have it on my phone because it is the lesser of two evils, have something vs. not having something, but are there any other options for the Tilt2?
Click to expand...
Click to collapse
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
BluEyedTiger said:
I haven't really had any trouble with mine popping off. It took a bit to get the top on right and it was a pretty snug fit too. Getting the corner edges all the way tucked under was the hardest part. I'm guessing it's a manufacturing thing. Some say it's a tight fit and other say it's loose. I will agree that the sides on the top piece are flimsy because they're not attached the the phone but if they were it would probably make matters worse by either rubbing against the bottom piece or creating too big of a gap between the two parts of the phone.
I agree there aren't many options for the Tilt 2 and I hate to say it but there probably won't be.
Click to expand...
Click to collapse
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Learic said:
If yours is a snug fit, I wonder if we received the same thing! Did you order from BoxWave? I have a little plastic tool that I used to get the corners onto the top half quickly which was actually made to fit into the creavice of a HTC Dash phone to pop the clips and take the phone apart. It works great and I can see the little flaps around the corner so you can tell the corners of the phone are between the gel lips.. It's still too easy to come off though..
Even though my receipt says "Praetorian Crystal Slip, HTC Tilt2, Smoke Grey - SKU: bw-268-3729-2808", it also says "ITEM: HTC TOUCH PRO2." The Box also has a white sticker in the top right that says "Praetorian Crystal Slip - TOUCH PRO2."
Do you remember if yours said the same? Maybe they somehow shipped me the wrong one?
Click to expand...
Click to collapse
Yeah I got mine directly from boxwave. They have like 3 different models of that slip. Most of the adds I saw on Amazon and eBay claimed it would fit on 3 or 4 different TP2 models which I knew it wouldn't. I emailed boxwave about the pics in their online catalog because it didn't look like a Tilt 2 to me and they admitted it wasn't. They said they didn't have one for the pics. Which made sense I mean why spend that much just to get pics but they promised it would fit so I figured what the hell. The hard covers kinda suck.
Thanks for the replies, I guess I will go ahead and order it and see what happens.
I just got the unbranded version of this case off ebay (the seller's id was e-story).
It's not too bad on my unbranded TP2. It's slightly more difficult to slide out the keyboard, and when the screen is fully tilted, the top row of keys are slightly obscured, but nothing too major in my opinion.
I like that the case improves the grip of the phone, but I'm also rather concerned that the case will eventually melt under hotter conditions since the material feels rather gummy.
*Note i have not experienced whether the product lives up to its name or not. I only JUST placed it on my device. This is simply my first impression.
**I included pictures of my device compared to the back parts of the adhesive so you can fully grasp the wonderful "custom to fit" experience.
I just now got as close to perfection as i think i am going to get with placing my "custom to fit" screen protector onto my device. At very first glance i saw that their were going to be some slight imperfections. The random circle on the top right of the adhesive was a dead giveaway. The cut out they have for the top speaker and the bottom row of buttons is hardly CLOSE to the size it should be. It is much too big. I am not sure if it is clear enough in the pictures but their is excess adhesive on the sides. I figured they may be meant to fold down to protect a minuscule amount of siding. At first i could not get it to stick on the sides. But after giving it a few minutes to settle and let the application spray* dry, it seems to be holding. However, the border has really ugly bubbles from the very tony inlay of the front of the phone. The instructions say that MICRObubbles will disappear in their own after a couple days... i hardly find these MICRObubbles though. We will see. I think it is almost supposed to have a "melting" effect on the device. Like heated plastic sort of taking the proper shape over the device.
Now we move onto the back. You will see that i have been given 3 holes instead of 2. (2 being the camera lens and the button underneath). I have no idea what the third was meant for.... I can also forget about taking the backing off of my device as it is now sealed shut with the plastic invisible shield. This doesn't bother me that much since i rarely ever have to take the back out but i know their will be a day where i will need to.
All-in-all the product LOOKS promising still. The bottom line here that i would like to make is that i have NO idea what TouchPro2 they are basing this off of. but it is far from mine. Too far. I need to check but i am also fairly certain they ask for your provider too (in case the device is different than others)
I am also still wondering about the excess sides. it is very random in the back but they make no mention of needing to trim the shield.
*They give you a spray that you use on your fingertips and the adhesive so that a. you dont give it fingerprint smudges and b. it doesnt fully stick right away so that you can "slide" it into place. I found that "sliding" it around was impossible because it still stuck but it did not stick enough to the point i was unable to retry.
I really hope this means something to somebody. Had i read something like this before hand, i may have thought longer on buying the product. I will be sure to write more in the next few days. By the feel of the material on my phone, it seems like it could work really well.
I would also love to know other people's experience with this product and even maybe correct me if anything i complained about was just due to stupidity.
It very much looks like you bought Invisible Shield for the wrong Touch Pro 2 model.
It looks like you have the one for the unlocked/unbranded model:
http://www.zagg.com/invisibleshield/htc-touch-pro-2-cases-screen-protectors-covers-skins-shields.php
When in fact you want the T-Mobile model.
http://www.zagg.com/invisibleshield/htc-touch-pro-2-t-mobile-cases-screen-protectors-covers-skins-shields.php
It looks like the shape of your T-Mob branded TP2 is actually quite different from the unbranded version. The shape of the shield is therefore quite different between the models, based on the pictures on the Zagg website. Also, the layout of the battery cover is totally different, which is why the cutouts on the shield don't match your battery cover. This also accounts for the 3rd small hole on this piece. In addition to the camera lens and speakerphone button, the unbranded TP2 has small holes for the speaker just below the speakerphone button, and that is what the 3rd hole in the shield is for. I'm guessing on the T-Mob version, the speaker hole is located as part of the larger cutout/hole.
Not to be mean but it's really obvious that it wasn't made for a T-Mobile Touch Pro2 and you should have known that it wasn't the right one.
Just going to the Touch Pro2 forums you can see that there's different versions of the device and ours is usually always referred as the "T-Mobile Touch Pro2" when being specific.
The cover does seem worth buying though.
Yeah i just inquired about it. I did buy the T-Mobile one and they just sent the wrong one.
redpoint73 said:
In addition to the camera lens and speakerphone button, the unbranded TP2 has small holes for the speaker just below the speakerphone button, and that is what the 3rd hole in the shield is for. I'm guessing on the T-Mob version, the speaker hole is located as part of the larger cutout/hole.
Click to expand...
Click to collapse
Oddly, the Tilt2 had little holes in the back case in the same spot, despite the fact that it is just the battery sitting behind the holes. I always figured it was just a way to give water quick access to the battery compartment to turn that little strip pink incase we ever dropped it somewhere damp...
I have never purchased anything from Ebay before, so I was hoping to get the opinion of those who are more experienced about case purchases from their. I was searching for a nice high quality bumper case, and I found quite a few on Ebay but one of them stood out the most, just seemed a lot more premium than the others (from the pictures) and way more thought out, has all the mic holes unlike some of the others where the one on the bottom corner is covered, even the rubber padding on the inside is engraved with the manufacturer logo (G.LIDER), and comes with a nice little screw cap screwdriver key chain. Hope to get your thoughts on it.
I included some images and here's the link/links:
http://www.ebay.com/itm/Anmboo-Meta...Cell_Phone_PDA_Cases&var=&hash=item19e3f95a0c
Edit: after i posted i noticed they put the corner mic cutout on the wrong side lol
http://www.ebay.com/itm/Black-Alumi...t=US_Cell_Phone_PDA_Cases&hash=item4acb6c3fe1
Mars196 said:
I have never purchased anything from Ebay before, so I was hoping to get the opinion of those who are more experienced about case purchases from their. I was searching for a nice high quality bumper case, and I found quite a few on Ebay but one of them stood out the most, just seemed a lot more premium than the others (from the pictures) and way more thought out, has all the mic holes unlike some of the others where the one on the bottom corner is covered, even the rubber padding on the inside is engraved with the manufacturer logo (G.LIDER), and comes with a nice little screw cap screwdriver key chain. Hope to get your thoughts on it.
I included some images and here's the link/links:
http://www.ebay.com/itm/Anmboo-Meta...Cell_Phone_PDA_Cases&var=&hash=item19e3f95a0c
Edit: after i posted i noticed they put the corner mic cutout on the wrong side lol
http://www.ebay.com/itm/Black-Alumi...t=US_Cell_Phone_PDA_Cases&hash=item4acb6c3fe1
Click to expand...
Click to collapse
Even I thought about buying one of these, but most likely your signal will get destroyed. I would try to find someone who bought one and get a review on it.
Pikezer1337 said:
Even I thought about buying one of these, but most likely your signal will get destroyed. I would try to find someone who bought one and get a review on it.
Click to expand...
Click to collapse
Yea that was one of my main concerns about it but cant find a review on one of these or similar, there's quite a few reviews on those full body aluminum cases which I hear drop signal tremendously.
Pikezer1337 said:
Even I thought about buying one of these, but most likely your signal will get destroyed. I would try to find someone who bought one and get a review on it.
Click to expand...
Click to collapse
Found a review on the Galaxy Note 2 forum where someone reviews 2 aluminum bumpers, he seems to lose a bar with the bumper on. Might greatly effect my data signal since i only get like 1-2 bars from Verizon at any given place in the Tampa Bay area but not my wifi.
Link to post:
http://forum.xda-developers.com/showthread.php?t=2019435
I had a similar metal bumper on my Note 2. The signal definitely decreased and my GPS kept having issues with attaining a lock/maintaining the lock
So actually, I just got mine, not sure if it's the same one, but I see no decrease in signal.
I tried speedtest.net app, but didn't see decrease in speed (at least significant enough).
I mean there was a slight decrease in speed, but that was like around 1~2 Mbps, and I'm still getting around 23 Mbps.
I learned a valuable lesson using metal bumper case, it scratch the trim and cause the paint to peel off. Also, many reported signal drop a bar or two.
I had an aluminum bumper on my iPhone 5 and had horrible signal. I personally would not recommend and aluminum bumper even though they look really nice on the phones
Sent from my SAMSUNG-SM-N900A using XDA Premium 4 mobile app
As far as I know the Note 3 doesn't have the phone antenna located in any corner, it is located from the top to the bottom, so there will be no issue in phone signal
Different thing is GPS antenna...
chhappy7 said:
So actually, I just got mine, not sure if it's the same one, but I see no decrease in signal.
I tried speedtest.net app, but didn't see decrease in speed (at least significant enough).
I mean there was a slight decrease in speed, but that was like around 1~2 Mbps, and I'm still getting around 23 Mbps.
Click to expand...
Click to collapse
Can you post some pics of it? Yea i don't think its a huge loss in signal, im usually on wifi so it doesn't matter much since i get full bars in all my classes, home and work, might be a problem on 4g since I only get like 1 bar. Does it in any way scratch the device, especially that chrome painted rim around the phone?
Mars196 said:
Can you post some pics of it? Yea i don't think its a huge loss in signal, im usually on wifi so it doesn't matter much since i get full bars in all my classes, home and work, might be a problem on 4g since I only get like 1 bar. Does it in any way scratch the device, especially that chrome painted rim around the phone?
Click to expand...
Click to collapse
It's quite a significant loss in signal. A bar or two. I only had mine on for about a day and I sold it for my N2. In areas where I'd normally get a slightly lower signal, the phone would drop reception altogether. Unusable.
ultwill said:
It's quite a significant loss in signal. A bar or two. I only had mine on for about a day and I sold it for my N2. In areas where I'd normally get a slightly lower signal, the phone would drop reception altogether. Unusable.
Click to expand...
Click to collapse
We don't have too many options in good looking bumper cases otherwise i would just buy a plastic one, its either this or the Spigen Neo Hybrid and that flimsy plastic bumper isn't too assuring, a lot of people have gotten it damaged right out of the box and others who have used it previously on their galaxy S4 had it damaged within a couple months, I need something sturdy that will show off the squarish design of the Note 3
Would of been awesome if Belkin made a view case for any other device excluding the iPhone
I want something like this : http://www.amazon.com/Belkin-View-C...96559&sr=1-2&keywords=griffin+iphone+5+bumper
for the Note 3, been searching for a while and cant really find anything similar except for those aluminum bumpers, the closest I have found is the Luvvitt Clearview but its still rounded instead of square and the bumper part is made of TPU.
http://www.amazon.com/LUVVITT®-CLEA...3897349&sr=1-2&keywords=galaxy+note+3+luvvitt
Mars196 said:
I have never purchased anything from Ebay before, so I was hoping to get the opinion of those who are more experienced about case purchases from their. I was searching for a nice high quality bumper case, and I found quite a few on Ebay but one of them stood out the most, just seemed a lot more premium than the others (from the pictures) and way more thought out, has all the mic holes unlike some of the others where the one on the bottom corner is covered, even the rubber padding on the inside is engraved with the manufacturer logo (G.LIDER), and comes with a nice little screw cap screwdriver key chain. Hope to get your thoughts on it.
I included some images and here's the link/links:
http://www.ebay.com/itm/Anmboo-Meta...Cell_Phone_PDA_Cases&var=&hash=item19e3f95a0c
Edit: after i posted i noticed they put the corner mic cutout on the wrong side lol
http://www.ebay.com/itm/Black-Alumi...t=US_Cell_Phone_PDA_Cases&hash=item4acb6c3fe1
Click to expand...
Click to collapse
I started a thread about the Love Mei aluminum bumper. There were members that said they had signal drops, but in my case, I cannot confirm this for my usage.
But the Love Mei is missing the hole on the lower right side of the phone, too. At least they just forgot instead of putting it in the wrong side :silly:
Mikegrmn said:
I started a thread about the Love Mei aluminum bumper. There were members that said they had signal drops, but in my case, I cannot confirm this for my usage.
But the Love Mei is missing the hole on the lower right side of the phone, too. At least they just forgot instead of putting it in the wrong side :silly:
Click to expand...
Click to collapse
Yea I checked that one out too, it was my first option before I came across this one.
Mars196 said:
Edit: after i posted i noticed they put the corner mic cutout on the wrong side lol
Click to expand...
Click to collapse
That's actually the temperature/humidity/etc. sensor. you can blow hot air into it and watch the temp rise with any sensor app. If you never use that stuff, I wouldn't think it'd be a big deal. But the reception loss could be a big bummer.
babyshanks said:
That's actually the temperature/humidity/etc. sensor. you can blow hot air into it and watch the temp rise with any sensor app. If you never use that stuff, I wouldn't think it'd be a big deal. But the reception loss could be a big bummer.
Click to expand...
Click to collapse
Actually, I drilled a hole in my bumper just this morning. The outcome is unfortunately not so pretty as my newly drilled hole was offset at first, but I think I can live with that.
babyshanks said:
That's actually the temperature/humidity/etc. sensor. you can blow hot air into it and watch the temp rise with any sensor app. If you never use that stuff, I wouldn't think it'd be a big deal. But the reception loss could be a big bummer.
Click to expand...
Click to collapse
Weird that they would include a cutout for the barometer but not the mic lol, i would think the mic is a bit more important (phone calls, video calls, videos in general)
Mars196 said:
Weird that they would include a cutout for the barometer but not the mic lol, i would think the mic is a bit more important (phone calls, video calls, videos in general)
Click to expand...
Click to collapse
Sorry maybe I wasn't too clear on my explanation, I meant the corner mic is actually not a corner mic hehe, thats a hole for the sensors.
babyshanks said:
Sorry maybe I wasn't too clear on my explanation, I meant the corner mic is actually not a corner mic hehe, thats a hole for the sensors.
Click to expand...
Click to collapse
Oh ok lol, not all that important to me, I don't need my phone to tell me if its hot or cold when I step outside, im sure I can feel it.
Mars196 said:
Can you post some pics of it? Yea i don't think its a huge loss in signal, im usually on wifi so it doesn't matter much since i get full bars in all my classes, home and work, might be a problem on 4g since I only get like 1 bar. Does it in any way scratch the device, especially that chrome painted rim around the phone?
Click to expand...
Click to collapse
Check out my post in this thread.
Someone asked me almost the same question.
http://forum.xda-developers.com/showthread.php?p=48113076#post48113076
But basically, for me, I saw no signal loss, 4G or 3G or cell signal, or even GPS.
I do use Verizon, which tends to be very good where I live.
Also, it does have black sticker-like things inside so that sides are not scratched.
hi as many note 3 users know, the plastic side frame is easy to get damaged, i have few cracks and one line just under the main power button (not sure just facial or completely crack?)
so, how easy is to change and which one i have to buy ? - im quite noob in hardware sides.
Sure you can buy one on Ebay
I have the same problem, the silver plastic bezel is very fragile.
If you search in Ebay you can found the Bezel and some of them come with tools to turn this in a complete DIY.
Actually i found all the body for this phone in ebay, so you can turn your used and damaged note 3 into a "brand new" one.
Thanks 4 the info. Where did you find it. Could you please share the link?
Thx in advance
hey guys.here is a link for the bezel replacement Bezel On EBAY
i want to tell you that it's not that easy to change it as you need to move the lcd screen from the one bezel to the other one.
there is glue between the lcd and the bezel so you need to warm it and remove it really carefully.i did the process yesterday on my note 3 and it was a pain in the a$$ so i have to tell you to be carefull before any move you re going to do.
Any link for Indian note 3?
Sent from my SM-N900 using XDA Free mobile app
I considered doing this, as I was given a note 3 a while back, but the bezel is beat to hell and the screen had a minor crack. I should've replaced both at the same time, but the small crack turned into a large one and needed immediate attention It's covered by a case now anyway though, so it's not much of an issue anymore.
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Its a tough job!!!
got my Note 3 as a gift from a friend who cracked it. I replaced the entire Display (along with frame)
and 3 days later I dropped it and got scratches in the frame.
so I decided to buy a frame and fix but its really a tough job.
so I got a bumper for 3$ and job done
I have installed one of those here http://www.ebay.com/itm/Thin-Aluminum-Metal-Bumper-Case-Cover-For-Samsung-Galaxy-Note-3-III-N9000-N9005/151251742076?_trksid=p2045573.c100033.m2042&_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D31478%26meid%3D341538ef5e9d4d6da3228a5f902e8cf1%26pid%3D100033%26rk%3D1%26rkt%3D4%26mehot%3Dpp%26sd%3D151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
thanks i thought i saw same one for bit less than that, will browse ebay later.
maskerwsk said:
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Click to expand...
Click to collapse
Photos plz
Up! I'm interested too.
yes i just remember i have some sand paper at home please post photo and detailed instructions... cheers
rockbastard said:
I have installed one of those here http://www.ebay.com/itm/Thin-Alumin...id=100033&rk=1&rkt=4&mehot=pp&sd=151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
Click to expand...
Click to collapse
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
triad88 said:
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
Click to expand...
Click to collapse
I haven't noticed any drop in reception at all
rockbastard said:
I haven't noticed any drop in reception at all
Click to expand...
Click to collapse
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Mr.Ultimate said:
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Click to expand...
Click to collapse
you have a lot of cases!
erwinsie said:
you have a lot of cases!
Click to expand...
Click to collapse
little too many ... beware that those wooden cases are the coolest thing your phone can get but if you do drop your phone they crack and break apart sometimes... not always though but alot alot sooner than any plastic case would and thats a heartbreaking thing because there not exactly cheap case, but hey - how often does someones phone feels and smells like real fresh quality piece of wood? I like them wooden ones very much even if they crack and put some tax on my pocket at the end of the day its almost like your personal signature of style ... besides, its always warm to touch and zero signal interference
PS: lots more were thrown out many months ago, especially all those metalized ones, no use to me nor could I offer them to anyone I knew who had note 3 due to what they are
When my display was damaged, it got repaired, not only the glass, but the whole display including the bezel, it was 1 piece.. I guess it's very hard to replace only the bezel