Related
Hey guys,
Iv got a stock US tablet Z, SGP311 on 10.4.1.b.0.109
Iv tried holding power and volume + while booting to get into stock recovery, iv tried tapping Vol+ a few times while booting, iv tried holdin Vol+ for 3 seconds and then hitting power......i cant get this damn thing into recovery!
Can someone help??
Snazarian said:
Hey guys,
Iv got a stock US tablet Z, SGP311 on 10.4.1.b.0.109
Iv tried holding power and volume + while booting to get into stock recovery, iv tried tapping Vol+ a few times while booting, iv tried holdin Vol+ for 3 seconds and then hitting power......i cant get this damn thing into recovery!
Can someone help??
Click to expand...
Click to collapse
There is no Recovery Mode in the XTZ's stock firmware. Here is how to access the available functions of the stock firmware.
1. Power On
Press and hold the POWER button until notification light flashes once, then release POWER button.
2. Power Off
Press and hold the POWER button until menu appears, then select "Power off" and "OK".
3. Restart
Restart device to turn off all running applications and to free up memory.
3.1. Simultaneously press and hold the VOLUME UP and POWER buttons for 10 seconds.
3.2. After the notification light flashes three times, release the buttons.
3.3. The device will power off automatically.
3.4. After the device is powered off, power on the device.
4. Reset
Reset device to its original settings to free up memory.
Don't forget to back up any important data saved on the device!
4.1. Go to Settings > Backup & reset > Factory data reset > Reset tablet.
5. Enable Safe Mode
5.1. Power off the device.
5.2. Press and hold the POWER button until the notification light flashes once.
5.3. Wait until the Xperia™ logotype disappears.
5.4. Press and hold the VOLUME DOWN button.
5.5. The device will restart in Safe Mode.
5.6. To exit Safe Mode, restart the device.
6. Flash Mode
6.1. Power off the device.
6.2. Connect a USB cable to the device.
6.3. Press and hold the VOLUME DOWN button.
6.4. Connect the USB cable to a computer.
6.5. Wait until the notification light flashes red-green once, then release VOLUME DOWN button.
6.6. To exit Flash Mode, disconnect the USB cable.
7. Fastboot Mode.
7.1. Power off the device.
7.2. Connect a USB cable to the device.
7.3. Press and hold the VOLUME UP button.
7.4. Connect the USB cable to a computer.
7.5. Wait until the notification light flashes red then solid blue, then release VOLUME UP button.
7.6. To exit Fastboot Mode, disconnect the USB cable.
8. Service Menu
8.1. Start the Contacts app.
8.2. Go into Settings.
8.3. Touch the blank area at middle bottom of screen for at least five seconds then stop touching screen.
8.4. "Enter service mode" button will be displayed.
8.5. Press the "Enter service mode" button.
8.6. Enter *#*#7378423#*#* (*#*#SERVICE#*#*).
8.7. Service menu will be displayed.
8.Notes.1. Enter *#*#4636#*#* (*#*#INFO#*#*) to display testing information.
8.Notes.2. Enter *#*#73556673#*#* (*#*#SELLMORE#*#*) to toggle Demo Mode activation on/off. WARNING! Activating Demo Mode will delete all personal content (photos, etc.) and settings.
How do you flash CM then ?
Cat McGowan said:
There is no Recovery Mode in the XTZ's stock firmware.
Click to expand...
Click to collapse
Thanks for telling ! I had been looking for this information for a long time.
Apparently, my service info says "bootloader unlock allowed: yes", I wonder if it means that I actually unlocked it or that the device would accept me to do it.
I moreover wonder how one can manage to install CM or root its device without using Recovery Mode. I saw on your signature you rooted your device. May I ask how you did that ?
ducasse.isidore said:
Thanks for telling ! I had been looking for this information for a long time.
Apparently, my service info says "bootloader unlock allowed: yes", I wonder if it means that I actually unlocked it or that the device would accept me to do it.
I moreover wonder how one can manage to install CM or root its device without using Recovery Mode. I saw on your signature you rooted your device. May I ask how you did that ?
Click to expand...
Click to collapse
It means your bootloader CAN BE unlocked.
To install a ROM, such as CM, you first unlock your bootloader, then move the ROM zip to your device. After that, you flash the included kernel from the zip with fastboot. Then, you boot into the included recovery from the kernel and flash the whole ROM.
Sent from my LT26i using Tapatalk
Felimenta97 said:
It means your bootloader CAN BE unlocked.
To install a ROM, such as CM, you first unlock your bootloader, then move the ROM zip to your device. After that, you flash the included kernel from the zip with fastboot. Then, you boot into the included recovery from the kernel and flash the whole ROM.
Sent from my LT26i using Tapatalk
Click to expand...
Click to collapse
I finally found a solution to my problem : I unlocked the device using flashtool-0.9.11's gui procedure, instead of flashtool's fastboot. It succeeded and I can successfully flash anything I want on the device.
I found your rational approach to my problem useful. It helped me isolate a solution. Thanks !
Hi there
I know this is an old thread. But my problem is same. I got this devide called sony experia tablet z lte ntt docomo x variant
My problem is that it got a lock screen and i have forgot the password. So i want to reset it.
But the problem is how do i do that, there isnt a recovery on this thing.
I was playing around with the buttons and i dont know how ,or which combination i pressed the tab booted to a factory reset screen but i wanst sure to reset that time so i exited from that and tablets lock screen appeared.
And now i cant figure out that how to do this again. Please help me
......
Hi there
I know this is an old thread. But my problem is same. I got this devide called sony experia tablet z lte ntt docomo x variant
My problem is that it got a lock screen and i have forgot the password. So i want to reset it.
But the problem is how do i do that, there isnt a recovery on this thing.
I was playing around with the buttons and i dont know how ,or which combination i pressed the tab booted to a factory reset screen but i wanst sure to reset that time so i exited from that and tablets lock screen appeared.
And now i cant figure out that how to do this again. Please help me
......
Press and hold the Power and Volume Down keys for 10 seconds.
The device will reset and restart.
Hi there
I have recently been given a broken Sony Xperia Tablet Z. When the power button is pressed a red light flashes 3 times but nothing happens. When the vol+ and power is pressed nothing happens. When the vol- and power is pressed the red light flashes three times again.
Is there anything I can do to fix it?
Many thanks!
mustango said:
Hi there
I have recently been given a broken Sony Xperia Tablet Z. When the power button is pressed a red light flashes 3 times but nothing happens. When the vol+ and power is pressed nothing happens. When the vol- and power is pressed the red light flashes three times again.
Is there anything I can do to fix it?
Many thanks!
Click to expand...
Click to collapse
charge it for several hours, and then try to switch it on or flash with flashtool..
Rootk1t said:
charge it for several hours, and then try to switch it on or flash with flashtool..
Click to expand...
Click to collapse
Hi there!
I've had on charge for a while now and still nothing. Would I need to be able to get into Download mode to flash with flash tool?
Thanks!
After charging the tablet for several hours, do this.
Press vol up + power button and hold until white led blinks 3 times.
(This will make sure the tablet is properly powered off. If after a long period no 3 blinks of white led, then it might mean that tablet state is already off. Press and hold just the power button and see if white led will blink just once then let go power button. The Sony logo should follow. All this is to see if tablet can shut down or power up properly or not. If it cannot do even the basic, then I have no idea how to proceed. This is why I don't trust my important data's in the internal emulated sdcard. I prefer my data to be in removable microsd. If tablet becomes dead and cannot be switched on, then any data that is stored in the unremovable internal emulated sdcard will be trapped. )
If you are lucky, the white led blinks 3 times it means that the tablet can be properly shut down, then ..
Then, connect a usb wire to the tablet. Do not plug the cable to the pc yet. without pressing power button, plug the cable to the PC WHILE you press and hold vol up button.
If you get a blue led at the side of the tablet, it means your tablet can be put into fastboot mode.
Do this first. I believe that once the tablet can be put into fastboot mode, then the tablet can be restored by flashing a recovery boot loader.
If you cannot get the tablet into fastboot mode, then I do not have enough knowledge about how to proceed. You will need to bring it to a service center for repairs.
cphilip said:
After charging the tablet for several hours, do this.
Press vol up + power button and hold until white led blinks 3 times.
(This will make sure the tablet is properly powered off. If after a long period no 3 blinks of white led, then it might mean that tablet state is already off. Press and hold just the power button and see if white led will blink just once then let go power button. The Sony logo should follow. All this is to see if tablet can shut down or power up properly or not. If it cannot do even the basic, then I have no idea how to proceed. This is why I don't trust my important data's in the internal emulated sdcard. I prefer my data to be in removable microsd. If tablet becomes dead and cannot be switched on, then any data that is stored in the unremovable internal emulated sdcard will be trapped. )
If you are lucky, the white led blinks 3 times it means that the tablet can be properly shut down, then ..
Then, connect a usb wire to the tablet. Do not plug the cable to the pc yet. without pressing power button, plug the cable to the PC WHILE you press and hold vol up button.
If you get a blue led at the side of the tablet, it means your tablet can be put into fastboot mode.
Do this first. I believe that once the tablet can be put into fastboot mode, then the tablet can be restored by flashing a recovery boot loader.
If you cannot get the tablet into fastboot mode, then I do not have enough knowledge about how to proceed. You will need to bring it to a service center for repairs.
Click to expand...
Click to collapse
Rootk1t said:
charge it for several hours, and then try to switch it on or flash with flashtool..
Click to expand...
Click to collapse
Hi there!
Thank you both for your help! I can successfully get the device into fastboot mode.
When trying to enter flashmode the device flashes green then goes back to red.
Is there anyway of fixing the device?
Many thanks!
First thing you need is a recovery boot loader.
This link helped me but I use Ubuntu linux to install recovery boot loader into my Tablet z wifi. (I think it is also possible to do it in windows but you will need to install proper drivers)
Before this step, I also used Flashtool under windows 7 to unlock my bootloader. It is not difficult to use Flashtool and unlock bootloader but you must decide how important it is to you to backup TA before unlocking bootloader. In my case, I didn't feel I need SONY bravia engine, so I didn't backup my TA.
1. Use Flashtool to UNLOCK
2. Use Fastboot to install TWRP recovery loader
3. Download a Custom Rom (CM11/CM12/Omnirom./PAC) and save it to microsd
4. Boot into TWRP Recovery, clean data / cache partitions and flash custom rom from microsd
http://forum.cyanogenmod.org/topic/93490-soft-bricked-my-xperia-installing-cm/
To fix the problem, I downloaded CMB from http://forum.xda-dev...d.php?t=2463423. I unzip'd it, and used fastboot to install the boot.img: "sudo ./fastboot -i 0xfce flash boot pollux-windy/cmb/boot.img". Then I rebooted into TWRP recovery, and wiped/reformatted everything (including /data, which CWM wouldn't mount or wipe). I then sideloaded the CM11 ROM, booted back into TWRP, and installed CM11 from within TWRP. I ended up reflashing the CMB boot.img back on, even after installing CM11, and everything seems to be running great now.
Hi, same problem. Good answer was here : https://fr.ifixit.com/Réponses/Afficher/273255/black+screen+and+red+led+blinking+3+times#
In fact, my Aukey Quick charger did the thing: https://www.amazon.fr/AUKEY-Charge-Chargeur-Secteur-Samsung/dp/B01AHY1XAY
Hi guys,
I was following various guides on here to install the cyanogenmod 11.0 ROM http://forum.xda-developers.com/xperia-u/p-development/rom-cyanogenmod-11-0-t2626639 and I have run into an issue.
I put the gapps zip and the ROM zip into the internal storage of the phone. I then typed "fastboot flash boot boot.img" into cmd and that went OK. When that was done, I did "fastboot reboot." The phone then showed the Sony logo screen (although it is different from the one I am used to seeing - it shows XPERIA STE at the bottom, but I assume this is normal?), then this screen turned off and on again repeatedly. I then mashed the volume up key and eventually it entered into the CWM recovery. I then selected to install the ROM zip, it did some loading and installing and stuff, as expected. The same Sony XPERIA STE screen came on again, and keeps turning on and off. This time however, I cannot get into CWM recovery mode.
If I hold the power button and volume up, it vibrates once, then the screen comes on and off again. If I hold the power button and volume up, wait for the single vibration and keep holding, it vibrates three times and is then completely off. If i plug it into the computer, the screen comes on and off. If I plug it into the computer and hold the volume up, it enters fastboot mode without trouble.
Thanks in advance for any advice.
hedgy03 said:
Hi guys,
I was following various guides on here to install the cyanogenmod 11.0 ROM http://forum.xda-developers.com/xperia-u/p-development/rom-cyanogenmod-11-0-t2626639 and I have run into an issue.
I put the gapps zip and the ROM zip into the internal storage of the phone. I then typed "fastboot flash boot boot.img" into cmd and that went OK. When that was done, I did "fastboot reboot." The phone then showed the Sony logo screen (although it is different from the one I am used to seeing - it shows XPERIA STE at the bottom, but I assume this is normal?), then this screen turned off and on again repeatedly. I then mashed the volume up key and eventually it entered into the CWM recovery. I then selected to install the ROM zip, it did some loading and installing and stuff, as expected. The same Sony XPERIA STE screen came on again, and keeps turning on and off. This time however, I cannot get into CWM recovery mode.
If I hold the power button and volume up, it vibrates once, then the screen comes on and off again. If I hold the power button and volume up, wait for the single vibration and keep holding, it vibrates three times and is then completely off. If i plug it into the computer, the screen comes on and off. If I plug it into the computer and hold the volume up, it enters fastboot mode without trouble.
Thanks in advance for any advice.
Click to expand...
Click to collapse
Press the power button repeatedly to enter TWRP recovery. Then, wipe everything except sd card/internal storage. Then, install the rom as usual.
I accidentally restore a backup (of my previous Z2 which was on my sd card through TWRP) on my Z2 on Exsistenz LP ROM yesterday. After that phone wont boot. Battery was .70% at the time of death. Red blinking led is seen when connected to usb cable. POWER + VOL UP doesn't give 3 vibes as intended, in fact nothing. Neither red hard reset button(Tried pressing it for >3mins). Cannot enter flash mode or fast boot modes .(tried to flash stock ROM through flash tool-failed). Only red blinking LED appears when usb cable connected.
Wierd to found when I press hard reset button while pressing POWER button it gives 3 vibes. But nothing changed.
Tried "pressing and holding all 3 buttons (power,vol+and vol-) all at the same time till it vibrates once then let go of the power button and vol+ but keep holding vol - while plugging in the usb cable this MiGHT boot your phone into flash mode" But didn't vibrate while holding all 3 buttons.
Its out of warranty period as well.
Please help me to recover to recover??? :crying:
use flashtool and flash stock ftf.
connect phone with usb cable when flashtool prompt to connect the phone
jhha said:
I accidentally restore a backup (of my previous Z2 which was on my sd card through TWRP) on my Z2 on Exsistenz LP ROM yesterday. After that phone wont boot. Battery was .70% at the time of death. Red blinking led is seen when connected to usb cable. POWER + VOL UP doesn't give 3 vibes as intended, in fact nothing. Neither red hard reset button(Tried pressing it for >3mins). Cannot enter flash mode or fast boot modes .(tried to flash stock ROM through flash tool-failed). Only red blinking LED appears when usb cable connected.
Wierd to found when I press hard reset button while pressing POWER button it gives 3 vibes. But nothing changed.
Tried "pressing and holding all 3 buttons (power,vol+and vol-) all at the same time till it vibrates once then let go of the power button and vol+ but keep holding vol - while plugging in the usb cable this MiGHT boot your phone into flash mode" But didn't vibrate while holding all 3 buttons.
Its out of warranty period as well.
Please help me to recover to recover??? :crying:
Click to expand...
Click to collapse
Something similar happened to me recently...wonder if this is a bug in a new release or something
This is what I did.
If you can't turn off phone, turn it off using the hard reset button http://sony-xperia.mobi/eng/sony-xperia-z2/231-how-to-do-a-hard-reset-and-reboot-a-sony-xperia-z2-physical-hard-reset-button-sony-xperia-z2.html
There's a really good guide on bricked z2 somewhere on xda but I can't find it anymore . What it said was useflashtools and flash and old ftf e.g. 4.4.4 or 4.4.2 and make sure to wipe apps_log and user_data in settings.
This might also help http://forum.xda-developers.com/showthread.php?t=1849170
Thanks for advice. The problem is it wont connect in flash mode. (attached usb with VOL DOWN button pressed & hold still gives only red blinking led)
jhha said:
Thanks for advice. The problem is it wont connect in flash mode. (attached usb with VOL DOWN button pressed & hold still gives only red blinking led)
Click to expand...
Click to collapse
Did you get it fixed?
jhha said:
Thanks for advice. The problem is it wont connect in flash mode. (attached usb with VOL DOWN button pressed & hold still gives only red blinking led)
Click to expand...
Click to collapse
If you restored another XZ2 with LOCKED BOOTLOADER's backup you probably killed your phone.
Was your bootloader unlocked?
Restoring anothers TA partition kills your device because drm keys are uniq
Hi!
M4 Aqua, E2303
Brief history, what I did before:
- On a full stock OS, first, I unlocked bootloader with fastboot oem unlock, which went through nicely.
- After that, I followed this thread to install custom recovery (twrp). Went through nicely (fastboot flash recovery recovery.img and fastboot flash boot boot.img).
- I was able to boot into recovery (twrp), and with the Install function, selecting Conceptify .zip it installed, rebooted.
- On the boot, the Conceptify gear logo was stuck spinning for a very long time. Then I just tried going into TWRP again to install Conceptify again, maybe for the second try it installs without the boot issue.
After this, I was no longer able to enter twrp recovery again. Okay, tried to flash the .img's again (boot and recovery), maybe I can at least get into TWRP recovery again, but no luck, despite both flash commands going through (both sending, writing were OKAY), without errors.
Current symptoms at this point:
- I still can get into fastboot (vol Up + usb plug in; LED red, then blue), and my PC can recognize the phone being in fastboot correctly, with serial number (in fastboot devices). It can still perform the flash/erase commands, but whenever I try fastboot reboot or fastboot reboot-bootloader, it doesn't reboot the phone. At this point, fastboot devices gives back a device in fastboot mode, but with a lot of question marks (?) instead of the serial number. On unplugging it, LED stays blue, like it is frozen or somthing. I kill the phone off with the power cutoff switch (next to microsd).
- holding just Power to turn on phone: Sony logo on the white background and is stuck. After a while I kill off with power cutoff.
- holding Power + vol Up, it vibrates once every 2 seconds or so. Nothing on screen, when I stop holding the buttons, stop vibrating. It however stays in a weird state, cause I can't get into fastboot for example (vol down + usb plug in; like I can do when it was powered off completely). I kill off with power cutoff.
- holding Power + vol Down: Sony logo on the white bkg, and stuck. After a while I kill off with power cutoff.
- tried the all-button hold: Power + vol Down + vol Up for 30 seconds, it was just vibrating every 2-seconds.
- flashmode with Flashtool: I downloaded a stock .ftf, loaded into FlashTool, but upon asking to connect the phone while holding vol Down, it can't detect it. The phone however lights red, then green on the LED light. Tried with both a new Flashtool (0.9.32.0, and a recommended older one as well: 0.9.18.6).
Is there something else I could try to get a working TWRP recovery again, and be able to boot into it?
Thanks for your help!
My M4 (E2312) have pretty much the same symptoms: can not boot anything and just stuck on SONY logo, Flashtool does not recognize phone in flashmode (Vol -), just fastboot. And using fastboot to flash system, boot, recovery shows finished processes but phone does nothing new. And phone does not response well to USB, only after a reset then it updates the status.
I have Pexo ROM v3, custom TWRP, SkyMelon 9 I think,Rooted SuperSU and Magisk( has conflicts so when I boot some pop up says X app has stopped working. When I install some more apps to use it was ok, then the pop ups show up more and more and then it decides to boot loop to the stage we are now.
I have tried install 0.9.33 and 0.9.23.1( somehow only 0.9.23.1 can install 3 drivers), Xperia Companion, Emma, ggsetup 3.2.0.1, Driver SONY so0104 (so0113 ADB interface- status show it cannot start),
So either it is the drivers on computer, the computer USB ports, the phone's software or hardware defects lead to software that caused it.
bdnlspam said:
Hi!
M4 Aqua, E2303
Brief history, what I did before:
- On a full stock OS, first, I unlocked bootloader with fastboot oem unlock, which went through nicely.
- After that, I followed this thread to install custom recovery (twrp). Went through nicely (fastboot flash recovery recovery.img and fastboot flash boot boot.img).
- I was able to boot into recovery (twrp), and with the Install function, selecting Conceptify .zip it installed, rebooted.
- On the boot, the Conceptify gear logo was stuck spinning for a very long time. Then I just tried going into TWRP again to install Conceptify again, maybe for the second try it installs without the boot issue.
After this, I was no longer able to enter twrp recovery again. Okay, tried to flash the .img's again (boot and recovery), maybe I can at least get into TWRP recovery again, but no luck, despite both flash commands going through (both sending, writing were OKAY), without errors.
Current symptoms at this point:
- I still can get into fastboot (vol Up + usb plug in; LED red, then blue), and my PC can recognize the phone being in fastboot correctly, with serial number (in fastboot devices). It can still perform the flash/erase commands, but whenever I try fastboot reboot or fastboot reboot-bootloader, it doesn't reboot the phone. At this point, fastboot devices gives back a device in fastboot mode, but with a lot of question marks (?) instead of the serial number. On unplugging it, LED stays blue, like it is frozen or somthing. I kill the phone off with the power cutoff switch (next to microsd).
- holding just Power to turn on phone: Sony logo on the white background and is stuck. After a while I kill off with power cutoff.
- holding Power + vol Up, it vibrates once every 2 seconds or so. Nothing on screen, when I stop holding the buttons, stop vibrating. It however stays in a weird state, cause I can't get into fastboot for example (vol down + usb plug in; like I can do when it was powered off completely). I kill off with power cutoff.
- holding Power + vol Down: Sony logo on the white bkg, and stuck. After a while I kill off with power cutoff.
- tried the all-button hold: Power + vol Down + vol Up for 30 seconds, it was just vibrating every 2-seconds.
- flashmode with Flashtool: I downloaded a stock .ftf, loaded into FlashTool, but upon asking to connect the phone while holding vol Down, it can't detect it. The phone however lights red, then green on the LED light. Tried with both a new Flashtool (0.9.32.0, and a recommended older one as well: 0.9.18.6).
Is there something else I could try to get a working TWRP recovery again, and be able to boot into it?
Thanks for your help!
Click to expand...
Click to collapse
Yes, I also tried installing conceptify but it doesnt work. At this point its better if you stick with the stock rom, remove as much bloatware as possible and consider it a phone because almost none of the ROMs here work stability wise, or they maybe stable but some features like display brightness or speakers dont work. So I recommend you install stock rom via flashtool and then unlock the bootloader via flashtool again and install twrp again. Also if possible try reinstalling the drivers for the phone in flashtool. Hope this works mate.
Not my name said:
Also if possible try reinstalling the drivers for the phone in flashtool.
Click to expand...
Click to collapse
Thanks for your answer!
Unfortunately, I still can't make Flashtool recognize my M4 as booted in flashmode. Tried installing the drivers with \Flashtool\drivers\Flashtool-drivers.exe , but choosing the "Flashmode drivers" option, it failed during the install (I guess cause there wasnt a connected device that supports it), tried both with phone being connected in flashmode (volDown + plug-inUSB), and phone disconnected as well.
bdnlspam said:
Thanks for your answer!
Unfortunately, I still can't make Flashtool recognize my M4 as booted in flashmode. Tried installing the drivers with \Flashtool\drivers\Flashtool-drivers.exe , but choosing the "Flashmode drivers" option, it failed during the install (I guess cause there wasnt a connected device that supports it), tried both with phone being connected in flashmode (volDown + plug-inUSB), and phone disconnected as well.
Click to expand...
Click to collapse
Can you try it on a Linux PC I guess?