Hy everyone!
I have problem with my samsung galaxy tab P7500..it wont recognize my usb. in notification bar shows that is connected but it is not. there is no folder od something with my usb staff. it worked fine, and then just stopped. i dont know why
before, when i connected usb, tab opened a folder of usb, but now nothing..
did i miss something? where did i get wrong??
please heelp!!
P.S. sorry for my english
Switch to a different USB port. It seems like a stupid answer, but it is a common problem. Switching from the form factor USB ports (front panel) to the board mounted ports (rear panel) or visa-verse often works.
i know this may be an old post but here goes, i have the same problem, my PC tells me that the drivers for my tab are installed but i can not see it in my PC.
i connected it to different USB ports but still i can not see it.
i tried turning the debugging on/off still to no successes.
7500 tab, cyanogenmod 4.0.4 (9 nightly )
nobody850 said:
i know this may be an old post but here goes, i have the same problem, my PC tells me that the drivers for my tab are installed but i can not see it in my PC.
i connected it to different USB ports but still i can not see it.
i tried turning the debugging on/off still to no successes.
7500 tab, cyanogenmod 4.0.4 (9 nightly )
Click to expand...
Click to collapse
Try unistalling kies and the Samsung drivers, restart the pc and just install the driver. See if that works.
Sent from my GT-P7510 using XDA Free mobile app
i don't have kies and i have uninstalled the samsung drivers, restarted my PC but still nothing.
nobody850 said:
i don't have kies and i have uninstalled the samsung drivers, restarted my PC but still nothing.
Click to expand...
Click to collapse
Okay, I just googled your problem... Try removing the device from device management (sorry, it was a Dutch site, translation might be different) in Windows. Then reconnect it.
Sent from the mini galaxy in my hands! ?
Olivier V said:
Okay, I just googled your problem... Try removing the device from device management (sorry, it was a Dutch site, translation might be different) in Windows. Then reconnect it.
Sent from the mini galaxy in my hands! ?
Click to expand...
Click to collapse
i did that on 2 different pc's and still the same problem.
nobody850 said:
i did that on 2 different pc's and still the same problem.
Click to expand...
Click to collapse
Then I only have 2 more options available before I run out of ideas.
1) did you enable mtp under the storage options on your tab?
2) your USB cable might be defective. Try a different cable.
Sent from the mini galaxy in my hands! ?
Olivier V said:
Then I only have 2 more options available before I run out of ideas.
1) did you enable mtp under the storage options on your tab?
2) your USB cable might be defective. Try a different cable.
Sent from the mini galaxy in my hands! ?
Click to expand...
Click to collapse
it is working.
thank you
enable mtp under the storage options on your tab
nobody850 said:
it is working.
thank you
enable mtp under the storage options on your tab
Click to expand...
Click to collapse
Ah, great! I'm glad I could help
Hi
Hope somebody could help me.
my tab is p7500. official ics and rooted. i try to connect usb otg and it working by showing "USB connector connect" .
I can connect it with 1gb flash drive. But when i connect with 2 gb flash drive or higher, the tab will show "High-power usb device connected. cannot access to this device".
why it show like that? is the tab only can access flash drive with 1gb memory and below? or there is some setting that need to be done if want to connect with higher than 1gb flash drive?
Please see the picture attach...
tamhar said:
Hi
Hope somebody could help me.
my tab is p7500. official ics and rooted. i try to connect usb otg and it working by showing "USB connector connect" .
I can connect it with 1gb flash drive. But when i connect with 2 gb flash drive or higher, the tab will show "High-power usb device connected. cannot access to this device".
why it show like that? is the tab only can access flash drive with 1gb memory and below? or there is some setting that need to be done if want to connect with higher than 1gb flash drive?
Click to expand...
Click to collapse
i don't think that the p7500 supports more than 1gb of memory. i don't think that i have a flash drive in my p7500.
nobody850 said:
i don't think that the p7500 supports more than 1gb of memory. i don't think that i have a flash drive in my p7500.
Click to expand...
Click to collapse
thanks nobody850
i thought i could watch videos on my tab by using flash drive since now days videos [email protected] are more than 1gb especially with hd..so i don't have to connect my tab to [email protected] seems like i have to follow the usual way...
tamhar said:
Hi
Hope somebody could help me.
my tab is p7500. official ics and rooted. i try to connect usb otg and it working by showing "USB connector connect" .
I can connect it with 1gb flash drive. But when i connect with 2 gb flash drive or higher, the tab will show "High-power usb device connected. cannot access to this device".
why it show like that? is the tab only can access flash drive with 1gb memory and below? or there is some setting that need to be done if want to connect with higher than 1gb flash drive?
Please see the picture attach...
Click to expand...
Click to collapse
I can't believe that the p7500 wouldn't support flash memory over 1gb. I've heard of people using a USB hub that has it's own power supply for OTG.
---------- Post added at 12:49 PM ---------- Previous post was at 12:42 PM ----------
tamhar said:
thanks nobody850
i thought i could watch videos on my tab by using flash drive since now days videos [email protected] are more than 1gb especially with hd..so i don't have to connect my tab to [email protected] seems like i have to follow the usual way...
Click to expand...
Click to collapse
I like to just share a PC drive or folder on my network, then us ES File Explorer to find the video on your network and stream it over wifi to MX player on the droid. It's a little technical to set up, but a good thing to know.
Hi,
does any of the countless i9100 (not "G") ROMs have OTG support?
Best regards,
toshibashi
CyanogenMod does support OTG.
Just checked with CM12.1.
And when i remember correctly, Cm11 worked as well.
I have cyanogenmod 12.1-20160106 Nightly-i9100 kernel 3.064-cm-gd71763e [email protected] #1. I have enable Android debug brigde and usb debbuging but OTG is not working. The cable is tested on a sony experia tablet and works fine with usb mouse and usb flash drive. I have also download several programs like USB OTG Helper, Stick (something), and others i don't remember. One of them said s3c usb host driver is missing. Any idea how to fix OTG?
Thanks in advance
What is OTG?
Web_Monster said:
What is OTG?
Click to expand...
Click to collapse
OTG is the ability of a phone to connect USB devices with an adapter connected to the microUSB port. You can connect keyboards or USB sticks, for example.
Well I run stock CM12.1 and never had any problem with OTG. I don't know if it might be the problem that your USB OTG adapter is not from Samsung?
i have install remix os on usb stick i use it on acer aspire one zg5 .. i want to connect to an external monitor with vga cable but no signal can you help me ???
xhostluv said:
i have install remix os on usb stick i use it on acer aspire one zg5 .. i want to connect to an external monitor with vga cable but no signal can you help me ???
Click to expand...
Click to collapse
You're probably looking at video=*** stuff added to grub. But first press ALT&F1; press dmesg then unplug/replug external monitor a few times to check if the system picks it up; check with dmesg again.
Hey guys,
I installed the latest Remix onto a separate partition so I can dual-boot on my Windows 7 machine.
It seems to work fine, I guess. Detects my cheap little USB wifi adapter, at least. But it will not detect my Android phone when connected to PC via USB. Now I'm sure this is due to lack of Android-to-Android wired interface, and someone will probably recommend an OTG cable, but honestly, is there any way of forcing Remix OS to detect USB connection from an Android phone?
I have a kate SD with resurection remix on android 7.1.
I have
-a cable micro USB-USB female
-this RJ45 adapter + USB 3.0 ports
https://www.amazon.com/UGREEN-Ethernet-1000Mbps-Nintendo-Chromebook/dp/B00LLUEJFU
[in the comments, people make it work on android TV but a guy with samsung tabalet has no rj45]
=>WHen I plug a wifi mouse in the cable micro USB-USB female, the mouse is detected
=>When I plug the USB Hub+rj45 adpater+cable, I do not get a ethernet connection, but I do get the wifi mouse. I tried with PLANE MODE and without. WIFI is OFF.
THe USB hub+rj45 works well on windows. How do I get it to work on android ?
THe driver for android+linux is here http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=131;71;112 How can I install it on my phone?
blue whale said:
I have a kate SD with resurection remix on android 7.1.
I have
-a cable micro USB-USB female
-this RJ45 adapter + USB 3.0 ports
https://www.amazon.com/UGREEN-Ethernet-1000Mbps-Nintendo-Chromebook/dp/B00LLUEJFU
[in the comments, people make it work on android TV but a guy with samsung tabalet has no rj45]
=>WHen I plug a wifi mouse in the cable micro USB-USB female, the mouse is detected
=>When I plug the USB Hub+rj45 adpater+cable, I do not get a ethernet connection, but I do get the wifi mouse. I tried with PLANE MODE and without. WIFI is OFF.
THe USB hub+rj45 works well on windows. How do I get it to work on android ?
THe driver for android+linux is here http://www.asix.com.tw/products.php?op=pItemdetail&PItemID=131;71;112 How can I install it on my phone?
Click to expand...
Click to collapse
You will need to include this in android kernel and then flash that kernel. First learn how to compile kernel, then learn adding additional drivers and then compile your own kernel.