Hei everyone! I bricked my G2 MINI while tryin to unlock bootloader. I finally found a guide to unbrick it and via fastboot i have erased the LAF.IMG .
Now, when i try to get in download mode (battery at 0%, hold vol + button and connect usb cable) the phone shows for a second the "fastboot" screen that says to continue holding vol + for etnering download mode than ----> black screen and LG logo appears, black screen again and the phone reboot again and again...
Someone know how to get in fastboot without go in download mode?
I have only to get in fastboot then i'll push the boot,laf files to flash the complete firmware...PLEASE HELP!
mattia.frenk said:
Hei everyone! I bricked my G2 MINI while tryin to unlock bootloader. I finally found a guide to unbrick it and via fastboot i have erased the LAF.IMG .
Now, when i try to get in download mode (battery at 0%, hold vol + button and connect usb cable) the phone shows for a second the "fastboot" screen that says to continue holding vol + for etnering download mode than ----> black screen and LG logo appears, black screen again and the phone reboot again and again...
Someone know how to get in fastboot without go in download mode?
I have only to get in fastboot then i'll push the boot,laf files to flash the complete firmware...PLEASE HELP!
Click to expand...
Click to collapse
did you try pull out the battery
connect phone to pc press vol - and put the battery back in
i bricked my device and so i got into download mode and connected to lg tools and installed 4.4 kitkat again here is link if you need download tools
http://www.mylgphones.com/lg-software-tools-download
If he really erased LAF from his phone he can not get into download mode any more, because LAF is the download mode.
If he was in the situation where he could erase LAF he could have easily rescued his phone by flashing stock images.
Now it will be hard to rescue but there is nothing to loose any more.
You can try to get into fastboot by:
hold vol + button and connect usb cable.
As soon as you see the fastboot screen release all buttons.
Try to connect your phone via fastboot.
Try to flash original aboot + original LAF
Maybe flash original boot + system
or
Go to Download mode and flash original KDZ in emergency mode (CSE).
Zaaap72 said:
If he really erased LAF from his phone he can not get into download mode any more, because LAF is the download mode.
If he was in the situation where he could erase LAF he could have easily rescued his phone by flashing stock images.
Now it will be hard to rescue but there is nothing to loose any more.
You can try to get into fastboot by:
hold vol + button and connect usb cable.
As soon as you see the fastboot screen release all buttons.
Try to connect your phone via fastboot.
Try to flash original aboot + original LAF
Maybe flash original boot + system
or
Go to Download mode and flash original KDZ in emergency mode (CSE).
Click to expand...
Click to collapse
Thank u zaaap! Unfortunately even when i release all buttons the telephone get into the download mode (that dont exist anymore) and reboot... Im a fool that forget to push the laf stock. Anyway i bought a new motherboard... I think that replacing will solve my problem..
If you connect the phone to USB with a PC, does the PC show anything in explorer or device manager?
If yes, there is still a chance to recover it.
I'm referring to THIS task.
I have not done it before but it could work and you have nothing to loose.
Make sure you get the correct KDZ for your phone from HERE.
Extract the original images with WindowsLGFirmwareExtract
You can find the partition list HERE
Zaaap72 said:
If you connect the phone to USB with a PC, does the PC show anything in explorer or device manager?
If yes, there is still a chance to recover it.
I'm referring to THIS task.
I have not done it before but it could work and you have nothing to loose.
Make sure you get the correct KDZ for your phone from HERE.
Extract the original images with WindowsLGFirmwareExtract
You can find the partition list HERE
Click to expand...
Click to collapse
Nope man, i only hear the usb plug in/plug out sound of Win7 but nothing in explorer or the lg app on the pc. Its obvious that i have the drivers stock and the others of Android SDK platforms (i used adb and fastboot very uasually when the telephone was funtional).
Anyway thank u all for the help, i had the telephone bricked for the unlocking of the bootloader and i thought that my phone was over, the argument is very difficult to afford on this site and on this device, i sent the telephone at the LG Custom Care and they only told me that the motherboard was over and replace it costs 130€ (im Italian) so i reclined their offer (i have also a Oneplus X) but after some deep research on XDA i made big steps forward and maybe if didnt make the stupid thing of forgot to flash the laf stock, maybe i could be able to rescue my phone. So a big big big Thank to the community of XDA and a infinite f**k to LG Custom Care that they would stole me 130€.
Ps. I bought an LG D620 with the display destroyed for 30€ and ill replace the Motherboard.
Pps. Sorry for my bad English.
mattia.frenk said:
Nope man, i only hear the usb plug in/plug out sound of Win7 but nothing in explorer or the lg app on the pc.
Click to expand...
Click to collapse
OK, sounds good. And what does the devicemanager show?
Is there something like QHSUSB_BULK or Qualcomm HS-USB Qloader ?
Please how to install LG d620 LGE Android MTP Device driver. I tried all I can, to no avail. Pls help.
Ntarikon said:
Please how to install LG d620 LGE Android MTP Device driver. I tried all I can, to no avail. Pls help.
Click to expand...
Click to collapse
Wrong thread.
But, if you have a stock ROM, use LG's drivers. If you have a custom ROM, use Google's drivers.
Related
i flashed clockworkmod recovery from rom manager and then tried to boot in recovery but the p500 stuck on lg logo.
i tried to remove battery and then placing again but it wasn't starting.
pls help me i think my phone is brick or something like that
can you try what you find here: http://androidforums.com/getitnowmarketing/330813-all-one-recovery-thread.html
I've experienced the same thing long back, it happens when recovery gets damaged...don't worry, the phone is not bricked...I recovered it by flashing back official firmware by using KDZ...
I'm assuming, u r not able to go to recovery either...r u?
yes i'm not able to go to recovery
to use kdz, pc is required but, when i tried to connect the phone to pc using usb cable it wasn't regonised. what to do
dmayurx said:
yes i'm not able to go to recovery
to use kdz, pc is required but, when i tried to connect the phone to pc using usb cable it wasn't regonised. what to do
Click to expand...
Click to collapse
Try the 8th point mentioned in the post...
Code:
http://forum.xda-developers.com/showthread.php?t=883314
dmayurx said:
i flashed clockworkmod recovery from rom manager and then tried to boot in recovery but the p500 stuck on lg logo.
i tried to remove battery and then placing again but it wasn't starting.
pls help me i think my phone is brick or something like that
Click to expand...
Click to collapse
well lgmdp is the best and the safest method to get ur phn back to life http://forum.xda-developers.com/showthread.php?t=1324105
folow this to flash recovery http://forum.xda-developers.com/showthread.php?t=1318750 just be sure to enable usb debugging on phn before flashing any recovery via clockwork or even lgmdp
shhbz said:
well lgmdp is the best and the safest method to get ur phn back to life http://forum.xda-developers.com/showthread.php?t=1324105
folow this to flash recovery http://forum.xda-developers.com/showthread.php?t=1318750 just be sure to enable usb debugging on phn before flashing any recovery via clockwork or even lgmdp
Click to expand...
Click to collapse
My phone is stuck on LG logo. that means my android isn't booting. so, my point is how can i turn ON USB Debugging.
and the other thing is i installed my phone drivers to pc(win 7 32 bit) but my phone was not recognized so, how can I use the tools like KDZ updater or LGMDP.
Thanks for the reply dude
dmayurx said:
My phone is stuck on LG logo. that means my android isn't booting. so, my point is how can i turn ON USB Debugging.
and the other thing is i installed my phone drivers to pc(win 7 32 bit) but my phone was not recognized so, how can I use the tools like KDZ updater or LGMDP.
Thanks for the reply dude
Click to expand...
Click to collapse
u can use kdz with the emergency mode...nothing to do with the USB debugging...the problem is the phone is not recognized...try many times with the "shaking technique"...it will work for sure, it worked for me...
dmayurx said:
My phone is stuck on LG logo. that means my android isn't booting. so, my point is how can i turn ON USB Debugging.
and the other thing is i installed my phone drivers to pc(win 7 32 bit) but my phone was not recognized so, how can I use the tools like KDZ updater or LGMDP.
Thanks for the reply dude
Click to expand...
Click to collapse
well i am saying that be sure to enable usb debugging in future for the time just use the method to revive your phn back ,when ur phn is on just be sure usb debugging is enabled and than flash recovery using any method u r comfortable with, use the lgmdp method its safe and kdz flashing is used the shaking method when the phn is in dead condition as ur phn boot to lg logo so the lgmdp method will work even the kdz but the later one is bit risky.
Get lgdmp (firmware flasher) on PC
Link: http://*******/5v3zU
Open lgdmp.exe
Disable LG modem
Device manager -> modems
Go to emergency mode first.
For that:
Power off phone (even if by taking out battery) -> keep press volume up+back button and press power button.
Now u will enter emergency mode
In lgdmp click select port
Phone will be detected automatically -> press connect
Close the pop-up window that shows to select image file
Backup NV
Tools -> NV backup
Download recovery
Link: http://*******/5v3tT
Unzip the downloaded recovery into a folder
Open the extracted folder as the image folder in lgdmp
It will show some errors. Don't mind and just close the image selection window
Now press download in main window of lgdmp
It will flash recovery to the phone
After its complete u can boot to recovery by keycombination menu + volume down when pressing power button
Hope it will help
Edit: xda don't allow adfly links so download files from http://lg-p500-optimusone.blogspot.in/p/flashing-custom-recovery-cwm-from-lgmdp.html
Sent from my LG-P500 using XDA
God! What the hell are you doing!
Do you even know what happened to your phone; No!
So don't go for anything
You got your CWM 5.0.2.7 corrupted while flash
So just boot into fastboot mode and flash CWM 5.0.2.0 via fastboot method
@All here: If anyone of you, could please link him to fastboot unbrick method from Bytecode's repo
By the way. What ever you try but KDZ and LGPMD won't recogonise your phone
So no chance to use it
Most probably he will be confused like hell by seeing all those answers like
Go for lgmdp no go to kdz no phone bricked ma money oh GOD.. :banghead:
Am not spamming by the way lol........
doppelgänger said:
Get lgdmp (firmware flasher) on PC
Link: http://*******/5v3zU
Open lgdmp.exe
Disable LG modem
Device manager -> modems
Go to emergency mode first.
For that:
Power off phone (even if by taking out battery) -> keep press volume up+back button and press power button.
Now u will enter emergency mode
In lgdmp click select port
Phone will be detected automatically -> press connect
Close the pop-up window that shows to select image file
Backup NV
Tools -> NV backup
Download recovery
Link: http://*******/5v3tT
Unzip the downloaded recovery into a folder
Open the extracted folder as the image folder in lgdmp
It will show some errors. Don't mind and just close the image selection window
Now press download in main window of lgdmp
It will flash recovery to the phone
After its complete u can boot to recovery by keycombination menu + volume down when pressing power button
Hope it will help
Edit: xda don't allow adfly links so download files from http://lg-p500-optimusone.blogspot.in/p/flashing-custom-recovery-cwm-from-lgmdp.html
Sent from my LG-P500 using XDA
Click to expand...
Click to collapse
still phone stucks on lg logo.
nothing happens when I press the Vol up + return button.
i tried without emergency mode but it won't help
DJoptimus-One said:
God! What the hell are you doing!
Do you even know what happened to your phone; No!
So don't go for anything
You got your CWM 5.0.2.7 corrupted while flash
So just boot into fastboot mode and flash CWM 5.0.2.0 via fastboot method
@All here: If anyone of you, could please link him to fastboot unbrick method from Bytecode's repo
Click to expand...
Click to collapse
Is this what ur talking about i found this
http://forum.xda-developers.com/showthread.php?t=1088046
it isn't from bytecode(u may know this)
no following codes were shown on my screen
Symptom
You tried flashing a custom recovery like ClockWorkMod or Thunderg, or you flashed an incorrect ROM, and when you rebooted, it showed this screen:
Code:
fastboot mode started
udc_start()
DJoptimus-One said:
God! What the hell are you doing!
Do you even know what happened to your phone; No!
So don't go for anything
You got your CWM 5.0.2.7 corrupted while flash
So just boot into fastboot mode and flash CWM 5.0.2.0 via fastboot method
@All here: If anyone of you, could please link him to fastboot unbrick method from Bytecode's repo
Click to expand...
Click to collapse
I found this too a "FastBoot Tutorial"
http://forum.xda-developers.com/showpost.php?p=15122833&postcount=100
after select port nothing appears in new window
dmayurx said:
Is this what ur talking about i found this
http://forum.xda-developers.com/showthread.php?t=1088046
it isn't from bytecode(u may know this)
no following codes were shown on my screen
Symptom
You tried flashing a custom recovery like ClockWorkMod or Thunderg, or you flashed an incorrect ROM, and when you rebooted, it showed this screen:
Code:
fastboot mode started
udc_start()
Click to expand...
Click to collapse
Completely switch off your phone
Press Power + Home button
It will boot into fastboot mode and then just follow the method as shown on the thread (link that you mentioned)
Make sure to download 5.0.2.0 CWM recovery image from here
Two things that i wanna advise you about
1) Read that thread very carefully, understand what you are doing and follow each and every command.
2) Make sure to rename the download *.img file to recovery.img
Note that .img is the extension and not to be included in name
I'm sure this will help
Once done, type in fastboot reboot and wait for the phone to boot to the previous instance, where the phone was before this happened
Avoid using 5.0.2.7; its buggy
dmayurx said:
I found this too a "FastBoot Tutorial"
http://forum.xda-developers.com/showpost.php?p=15122833&postcount=100
after select port nothing appears in new window
Click to expand...
Click to collapse
Don't use this. Use the previous link you mentioned
DJoptimus-One said:
By the way. What ever you try but KDZ and LGPMD won't recogonise your phone
So no chance to use it
Click to expand...
Click to collapse
The same thing happened with my phone too, but I was able to revive it by kdz, flashing back stock froyo...and carried out the entire step again...anyway thanks for mentioning a faster technique...may come handy in future
kiran2cy said:
The same thing happened with my phone too, but I was able to revive it by kdz, flashing back stock froyo...and carried out the entire step again...anyway thanks for mentioning a faster technique...may come handy in future
Click to expand...
Click to collapse
Nice to hear that it helped others out too
I suffered from this about 20 times but it took me 2 minutes to recover back
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script to get into fastboot at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
So you solve it! :good:
:/
tawhid111 said:
How to fix partion problem !!!
After countlss hours of messing with the LG P769 This is how i got into S/W mode to work !:laugh:
ASSUMING you know how to install fastboot drivers there are instructions on the forum ...so follow those guide note fastboot drivers work best on windows 7 windows 8 was giving me hard time ...
1.install fastboot drivers
2.run lelus script at the same time hold vol+ button once the script shows the OMAP device close the script and immediately put the battery back in .The LG phone will boot into S/W mode !
Make sure you write down your imei or serial number AND make sure battery is fully charged . then
Now simply use the LG software tool or the KDZ offline flasher look around the forum for how to guides
Thats it
Click to expand...
Click to collapse
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
foreverman said:
Still unable to do it, when I plug the cable holding vol+ it just reboot normally :/
Click to expand...
Click to collapse
Then try enter in lelus fastboot mode, ad then flash x-loader, uloader, boot.img and recovery.img from stock rom for your device type model. Then repeat steps 1 and 2
Where can I find the lelus script?
Sent from my Note II
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Then you need a Technician with a Octopus Box to repair your partition table...
ciccillover said:
Sorry for reviving such an old thread, but oh well...
Your procedure doesn't seem to work with my device. Just to make sure we are using the same driver packages, can you post a link to the fastboot driver you have successfully used?
My L9 is always showing this "partition doesn't exist" error message, no matter what I try. Lelus's script seems to do the job and the phone is detected as a fastboot device, and can even be detected in LG Flash Tool (using a 910K cable), but flashing will stop after a little over 2 minutes, because the phone disconnects. During all of my attempts, the screen stays black.
Any hint?
Click to expand...
Click to collapse
Can you boot into recovery? We now have a custom recovery for locked bootloaders (and CM roms). If you can get into recovery, I would try some adb commands to mount the partitions.
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
ciccillover said:
No, no recovery. Just to make sure that I'm not doing it wrong, what is the key combination to boot to recovery?
I have also tried:
Code:
fastboot boot some_recovery_image.img
It says ok, but the phone just hangs at the black screen and becomes undetectable as a fastboot device, until I pull the battery. So, unless the some_recovery_image.img is unsuitable for my P760 (which may be!), there is something seriously wrong I think.
Or maybe I can try the same command with the custom recovery for bootloader locked phones... Where can I find it?
Click to expand...
Click to collapse
Your EMMC partition is wiped or fried... you really need a JTAG service or a Box like octopus because your L9 is Hard-bricked...
Thanks for your opinion. Yet, I still want to hear from others.
I'm running into more and more problems with the L9 as their me grows.
-Fastboot doesn't work under Windows 8.1 and 10, but under the now obsolete(for me) Windows 7, unlike my other devices, which are fine with Win 10.
-ADB seems to work, but requiring the device to be still able to boot.
-I always boot to recovery from within Android as long as the L9 ain't bricked. After a failed rom install, during which the sd card failed(could no longer write or be formatted afterwards, the last time stamps of files and folders were set during the failed install) I discovered a problem with TWRP(Artas182x's and Edwin's), which may have been present since a long time: Trying to invoke TWRP via keypress will brick the device!
So, if my P760 no longer boots, there's only download mode available, sort of the final line of defense.
-There's sort of a trick if even download mode fails: After a failed attempt unplug phone, force switch-off, if the phone is in brick state. Then switch on, force switch-off again, and only then attempt download mode again. And have patience while holding down the vol button, it might take up to 20 seconds for the phone to switch itself on into download mode. (A single forced powerdown will cause Fastboot NOT to work the next time)
But I'm absolutely clueless about the recovery issue, for now TWRP is semi-working, can only be accessed via Android, as long as the phone is fully working.
W/o Fastboot, I now have flashed stock rom several times and rooted it with Kingo rooter just to be able to run Flashify to install TWRP. If Flashify is the culprit for the TWRP issues, I could need a recommendation for a better working app.
ciccillover said:
Thanks for your opinion. Yet, I still want to hear from others.
Click to expand...
Click to collapse
Tried OMAP flasher ? It needs memory configuration file in order to work with our device
No, I didn't. I have sold the phone for spares.
Inviato dal mio LG-D855 utilizzando Tapatalk
I never needed the OMAP drivers and tools. As they are ancient, they will probably make even more problems with newer Windows versions.
I could by no means invoke Fastboot on this device with Windows 8.1 and 10, Seven worked. So you had to go for Download Mode instead to recover to stock rom, then root with the Kingo tool, then install TWRP via Rashr or Flashify, the most time consuming way to recover from the frequent bricks.
And the LG Flash Tool 2014 always needed several attempts to get the job done. The latest official recovery tool from LG works in D/L Mode, but will always download the rom image anew.
Hello,
today i tried to root my phone who runs on kitkat 44.2 and i v'e made a big mistake
i wanted to make my phone look like the g3
now its rooted but while it got in recovery i didnt know how to select the options so what i did was
i took my battery out and now i tried to get it on again and it won't
it doensn't want to get in recovery nothing
when i connect it with my phone it shows that its connected
i don't know what to do can someone help me pleasss i want it back like the beginning without the root pleas (((((
Sorry @Teamsvg,
but with this description no one can help you.
Please explain what you did.
How did you root?
What did you do to make it G3 like?
Did you flash anything?
I can not believe it bricked because of pulling the battery while in recovery, because I did the same when my phone was all stock and nothing wrong happened.
You may try: http://forum.xda-developers.com/showthread.php?p=54325341
Regards,
Zaaap
hi
Zaaap72 said:
Sorry @Teamsvg,
but with this description no one can help you.
Please explain what you did.
How did you root?
What did you do to make it G3 like?
Did you flash anything?
I can not believe it bricked because of pulling the battery while in recovery, because I did the same when my phone was all stock and nothing wrong happened.
You may try: http://forum.xda-developers.com/showthread.php?p=54325341
Regards,
Zaaap
Click to expand...
Click to collapse
hi, thnks for replying
this is what i tried
https://www.youtube.com/watch?v=KINp9v_GN3o
i didn't enable usb debugging ...
zaap
Zaaap72 said:
Sorry @Teamsvg,
but with this description no one can help you.
Please explain what you did.
How did you root?
What did you do to make it G3 like?
Did you flash anything?
I can not believe it bricked because of pulling the battery while in recovery, because I did the same when my phone was all stock and nothing wrong happened.
You may try: http://forum.xda-developers.com/showthread.php?p=54325341
Regards,
Zaaap
Click to expand...
Click to collapse
My phone is like this: you the screen is black, i forgot to enable usb debugging because i tried to root it in my phone so i ddin't need my computer, i can't get in download mode or recovery nothing ! i tried the buttns( and no my buttons works fine) how can i fix this? the link you've send me ask me to put my phone in download mode : "if your device is bricked and can't boot you'll have to enter the Download Mode, to do that just keep holding the Vol. Up button while inserting the USB cable in the phone( The USB cable must be already plugged into the PC while doing that), and you keep it until you go into the Download Mode."
but it can't ...
Teamsvg said:
My phone is like this: you the screen is black, i forgot to enable usb debugging because i tried to root it in my phone so i ddin't need my computer, i can't get in download mode or recovery nothing ! i tried the buttns( and no my buttons works fine) how can i fix this? the link you've send me ask me to put my phone in download mode : "if your device is bricked and can't boot you'll have to enter the Download Mode, to do that just keep holding the Vol. Up button while inserting the USB cable in the phone( The USB cable must be already plugged into the PC while doing that), and you keep it until you go into the Download Mode."
but it can't ...
Click to expand...
Click to collapse
autoirec is onyl for g2.. not mini. becouse we have locked bootloaders custom recoverys doesnt work. something similiar happened to my phone. i can tell you by confedens that first of all it doesnt sound that you are familiar with custom recoverys and stuff and that you have hard bricked your phone. i had to send mine in after 2 days of trying to make it start again. it is broken. and if you take it to service i wouldnt tell them what you did or that you rooted it.
Try this. If you phone is detected under sdb or sdc you have a chance to unbrick your phone.
I attached the files needed to unbrick G2 mini:
sbl1.img
aboot.img
rpm.img
tz.img
recovery.img - download from here.
Be very careful. The order of partitions for our phone is different from the LG G2. So then you use "gdisk -l /dev/sdb" command, find the partitions numbers of each file attached, and use that number in dd command.
I do not know why on tutorial for G2 there is a warning not to flash original recovery.img on recovery partition. So my advice is to flash all partition except recovery.img and see if your phone enter download mode. If not, flash recovery.img, you have nothing to lose.
If the phone enter download mode flash kdz.
powermetza said:
Try this. If you phone is detected under sdb or sdc you have a chance to unbrick your phone.
I attached the files needed to unbrick G2 mini:
sbl1.img
aboot.img
rpm.img
tz.img
recovery.img - download from here.
Be very careful. The order of partitions for our phone is different from the LG G2. So then you use "gdisk -l /dev/sdb" command, find the partitions numbers of each file attached, and use that number in dd command.
I do not know why on tutorial for G2 there is a warning not to flash original recovery.img on recovery partition. So my advice is to flash all partition except recovery.img and see if your phone enter download mode. If not, flash recovery.img, you have nothing to lose.
If the phone enter download mode flash kdz.
Click to expand...
Click to collapse
Can i use this files on G2 Mini D618?
Thanks!
No you can´t.
Sent from my LG-D620 using XDA Free mobile app
Hello
I think I've bricked my P760. When i want to run my phone it stuck on LG logo and can't boot to OS. Everything was fine but after installing fix to camera i could boot to OS my phone once and after reboot i can't boot to OS anymore. My phone has root, unlocked bootloader, custom recovery and custom ROM. I don't have acces to recovery. I have only acces to bootloader mode with fastboot (VOL+ + HOME + POWER). Then i have a note "Welcome to LG Fastboot Mode ". My computer detects it and automatically installs drivers (Fastboot interface (Google USB ID). But the problem is that in Device Manager it all time blinks. It's connected and immediately dissconects. I'm using original USB cable from LG charger. When i'm trying to use cmd in fastboot & adb files it's waiting for device all the time.
I don't know what I should do next :C
Pls help guys
SaRLaY said:
Hello
I think I've bricked my P760. When i want to run my phone it stuck on LG logo and can't boot to OS. Everything was fine but after installing fix to camera i could boot to OS my phone once and after reboot i can't boot to OS anymore. My phone has root, unlocked bootloader, custom recovery and custom ROM. I don't have acces to recovery. I have only acces to bootloader mode with fastboot (VOL+ + HOME + POWER). Then i have a note "Welcome to LG Fastboot Mode ". My computer detects it and automatically installs drivers (Fastboot interface (Google USB ID). But the problem is that in Device Manager it all time blinks. It's connected and immediately dissconects. I'm using original USB cable from LG charger. When i'm trying to use cmd in fastboot & adb files it's waiting for device all the time.
I don't know what I should do next :C
Pls help guys
Click to expand...
Click to collapse
I can help you. i just figured it out after walking away for a few weeks. pm me and ill tell you over google+ or skype and walk you through it.
i have same problem.
can someone solved it?
SaRLaY said:
Hello
I think I've bricked my P760. When i want to run my phone it stuck on LG logo and can't boot to OS. Everything was fine but after installing fix to camera i could boot to OS my phone once and after reboot i can't boot to OS anymore. My phone has root, unlocked bootloader, custom recovery and custom ROM. I don't have acces to recovery. I have only acces to bootloader mode with fastboot (VOL+ + HOME + POWER). Then i have a note "Welcome to LG Fastboot Mode ". My computer detects it and automatically installs drivers (Fastboot interface (Google USB ID). But the problem is that in Device Manager it all time blinks. It's connected and immediately dissconects. I'm using original USB cable from LG charger. When i'm trying to use cmd in fastboot & adb files it's waiting for device all the time.
I don't know what I should do next :C
Pls help guys
Click to expand...
Click to collapse
mirul_up said:
i have same problem.
can someone solved it?
Click to expand...
Click to collapse
pseudosane said:
I can help you. i just figured it out after walking away for a few weeks. pm me and ill tell you over google+ or skype and walk you through it.
Click to expand...
Click to collapse
Go through this thread http://forum.xda-developers.com/showthread.php?t=2292828 it will definitely solve your problem, from the screen-shot it seems that you are using windows 10, i'm not sure that omap4430 drivers will work on windows 10 or not, but you'll try otherwise do the process on windows 7, your phone will revive...
@Codeplex its to complicated thread.
before mine become like this my phone alway succes writing recovery via adb fastboot but now i try writing recovery via adb fastboot always filed.
flashing firmware with cmahendra method always get 15% error..
I think all dev not care anymore about our phone..,
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
EFAYSAL said:
Hi...
I try to root my FL02 (ALCATEL FLASH PLUS 2) every thing goes perfect and i get ORANGE STATUS but at the last step when trying to flash the rom with TWRP it could not read the SD card and system folder isn't abel to wipe so i try to repeat steps again.
first flasing in the video done and mobile restarting. no logo on screen and it doesnt boot and cannt go in boot mode or fastboot mode.
it connect and disconnect with PC but i still can connect it to flashing programme and i can send flash from PC but it doesnt boot and nothing appear on the screen.
any help....
Phone : FLASH PLUS 2
N D1M N7KE 03 TJZ
ANDROID 6.0
I follow this video to root
youtube.com/watch?v=d8zPGPJ_uZY
Click to expand...
Click to collapse
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
SubwayChamp said:
Ok, tell me to can help you;
Do you have TWRP installed?
Do you unlock bootloader succesfully?
In which modes you can enter? fastboot, recovery, download (do detects SPFlash Tool?)
Click to expand...
Click to collapse
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
EFAYSAL said:
Thank you SubwayChamp for help.
No , TWRP is not installed now .
Yes, I think bootloader has been unlocked. It is done with Orange status.
I think it is in download mode. it detects SPFlash.
Click to expand...
Click to collapse
Ok, I guess that your device is actually in bootloop and don´t booting.
Tutorial that you followed has many steps and don´t need to do all this to just root device and it contains some files like lk.bin that you can´t be sure that should be for your device.
Some users use this file (lk.bin) of an unlocked device and think that flashng in other device then get unlock it but no need, your device can be unlock it just follow some commands in fastboot mode.
Now you can do the next;
Try to flash again your rom stock (I guess that you don´t have a backup), if for some reason your official tool doesn´t work then use only some images like boot, system and userdata with the scatter.txt to flash them through SP Flash Tool.
Here a link to TWRP https://youtu.be/6vj_BY6xJdA, you can root it with supersu v2.78 0r v2.82 and here some files that can be usefull too https://drive.google.com/uc?id=0BwJgeCYTpnEHNlg2VUlieHFTYVU&export=download
Update steps that you are following to can assist. What extension has your rom and if it is recogniced for SP Flash Tool. I didn´t ask you if you can enter to fastboot mode and if you can then you can know if your bootloader is unlocked typing fastboot oem info
Most info that you give and some screenie will help to understand better
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
EFAYSAL said:
Unfortunatly, it can not enter to fastboot or recovery mode. Those files in replay didn't work and i dont have a backup. I try to flash recovery.img, system.img and preloader_shine_plus.bin . All done but it still black screen and does not boot. But now it connect to Pc without disconect .
I cant add link or images to my post.
Click to expand...
Click to collapse
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
SubwayChamp said:
Gmail didn´t warn myself about your post. Did you solve it?
You said that flashed recovery, system and preloader but how, through SPFlashTool?, if yes, are you sure that this tool recogniced your device?
You forgot to flash boot.img too.
Other way to try; flash only preloader.bin and then try flashing boot, system and userdata that are the three most important partitions to can boot.
Like last resort you can do a Format all + flash but only like last.
Click to expand...
Click to collapse
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
EFAYSAL said:
first of all thank you for your help. I was busy last week .
Yes it was with SPFlash and it is show MT6775 when mobile connect . but if i try flashing boot it gives an erorr and cant flashing.
I think i have a wrong boot file.
I miss userdata file.
Do you know where can i download necessary files for this model?
I apologize for delaying. It is time for school examin
Click to expand...
Click to collapse
I´m not sure if you are connecting correctly your device at right time and form to can flash it properly. Every device has more or less a specific way to do it. My last alcatel it was connected just with device power off and after to tap on download, but in other device Blu Dash was connected pressing just vol_up and my last mt6757 Bluboo had to press both vol up and down at time to connect to pc and after to tap on download option. To have sure that is well done increase volume in your pc, you will hear a first sound that is cause pc is recognicing but then you have to hear a second sound that is when SPFlashTool is recognicing device and you will see a red line in down side of the tool window, release button inmediately and let tool to work.
This is a good rom for your device according the author is optimized https://droid1311.blogspot.com/2017/08/alcatel-fl02-aka-flash-plus-2-via.html and this is the link directly if you have troubles with pop-up-adds https://drive.google.com/file/d/0BwAGh1drb91SeDZwV1VXbXpjQWM/view
Also you can try with other versions of SP Flash Tool, most stable maybe should be v5,1628 https://androidmtk.com/smart-phone-flash-tool leth me know how you go
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
SPFlashTool 5.1628:
I try all the way with and without pressing any button but no luck . And when it work finishing with error.
SPFlashTool 5.1628:
I try all the way to get that mode but nothing works. So I try to click download button then conect the phone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
EFAYSAL said:
If I understant, the status bar has to be red then I will release the mobile button and click download in SPFlashTool.
I try all the way to get that mode but nothing works. So I try to click download button then conect the pkone by random buttons and every time i get red color , yellow , green ,purple , yellow (for many times 100%)
then i get this error:
ERR: STATUS-SEC-IMG-TYPE-MISMATCH (0xC002002A)
Click to expand...
Click to collapse
There is a part that is not variable in the way to use this tool, ever you have to tap on download before to connect device and is recommendable too connect cable usb to pc (not yet to device); from here is when the button that you have to press can vary but like I said you before in my last mt6757 (a very similar to yours) works pressing both vol at same time to connect terminal cable to device and now you will see a red line (could be violet-ish)
Try before just flashing only preloader file to recreate some partitions and then do other flash for the other files.
Of course you have to be sure that all drivers are installed correctly cause this tool needs to put your device in download mode (a special level) and also keep it in this state so find VCOM drivers for Alcatel and adb/fastboot installer and try to uninstalling some older drivers that you don´t use and many times we keep in our pcs and for a short data transmission can helo that all the rom move it in same folder where SPFlashTool is allocated.
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
EFAYSAL said:
After updating drivers and trying all the possibilities buttons the red line doesnt appear.
Click to expand...
Click to collapse
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
- In what android version are you, 6.0?
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
- Did you try to flash just preloader, only this file?
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
SubwayChamp said:
Ok, here there are somethings that we need to know
- First of all don´t forget to charge your battery, after many attempts could consume a lot.
- Your device is recogniced in fastboot mode? mtk has two variables ways to enter to, pressing both vol + pwr till an options menu appear, then you have to select, and the other method most known is vol down+ pwr to go diirectly
Click to expand...
Click to collapse
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
SubwayChamp said:
- In what android version are you, 6.0?
Click to expand...
Click to collapse
Yes, last time it was 6.0 before the root
SubwayChamp said:
- What is the exact variant of your device, you can know maybe seeing in the box, this rom is for 5095K version 6.0 MM
Click to expand...
Click to collapse
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
SubwayChamp said:
- Did you try to flash just preloader, only this file?
Click to expand...
Click to collapse
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
SubwayChamp said:
If SPFlashTool don´t give signals of recognicing device is probably that your device is not now totally power off, try pressing pwr by 7 seconds, then try to flash again combining both vol with pwr button
Upload some screenshot about the process
Click to expand...
Click to collapse
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
EFAYSAL said:
Which option mode should appear? Screen is always black (off) all that i have on the phone is the LED.
I try more than 4 different drivers for Alcatel Flash Plus 2 (vcom & cdc) but no sound from SPFlash to prove that it recognise the phone. Sounds just release and keep relrease from Windows 10.
Yes, last time it was 6.0 before the root
Unfortunatly, I dont know . There is nothing on the box or manuel.
that is what i found on the box :
FL02
Venus gold H-B
FL02-2HLCEU2
- PWR+VOL(+) : reset the phone
It is done. all that i have to do is to tab on Download and then connect the phone and I dont need to press any button.
I did that but it is same.
Note:
Success fash always done without pressing any button on the phone. and I try it with and without buttons sometimes it is fail when I press a button and otherwise it work.
I have formated whole fash.
Click to expand...
Click to collapse
You need to try two different ways to flash files and restore your device.
First method: fastboot mode
You need to get device enter to fastboot in order to flash some files like system, boot and userdata, then there are two main methods to do it:
- Pressing pwr + vol down
- And I mentioned that sometimes work pressing both volume button + pwr and a menu have to appear to can select an option to enter to (fastboot mode), in some devices this method is not working but you have to try several times attempting to.
Second method: SPFlashTool
You have to ever press first of all Download box and connect terminal cable to pc and the buttons thhat you need to press at time to connec cable usb to your device may vary, sometimes vol down, sometimes both vol but never pwr button; if pc recognice then you have to release all buttone an let it pc continue the flash process.
If SPFlashTool recognice device first flash only preloader file and select now lk.bin too. Flash only these two files and after do again a new flash with the rest of the files, Why you need to do this? your partitions are corrupted and you need to restore them with these files in order to can flash all another files.
Before all of this charge your battery, if you have a cover removable then extract it some minutes and put it again.
Also I read that for this model it´s used this tool instead of SPFlash Tool https://androidmtk.com/download-sugar-mtk-sp-flash-tool (inside the zip you will find a password to start the tool) but I´m not sure what kind of rom it needs, you have to connect your device to begin the process, you will find in product models section in the tool this variant for your device "FL02"
Try first the other tool and then this and let me know how you go, mtk devices are almost unbrickeable so it´s just to find the appropriate way to return it to the life.
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
EFAYSAL said:
Hi again!
It was along time,I know . But I tried to know why I can’t return my phone back to life.
I have searched all possible websites for rom of this model and I have formatted my pc and installed win7 with all necessary drivers.
I can’t found any rom for it but now I can flash all the necessary files for boot they flashing and running smoothly but the mobile can’t boot up.
I try to use that app in your replay. It recognizes the device but stuck after that and keep looking for rom without any chance to download it.
I think I have a wrong rom files. I can’t find any other reason but this.
I will write again all information about my phone:
It is called Alcatel Flash Plus 2
I bought it from AliExpress and it came from Indonesia as I remember (not sure)
On battery wrote:
FL02
TCL communication Ltd
FL02-2HLCEU2
Click to expand...
Click to collapse
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
I understand that you tried with Sugar tool with no lucky.
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Is there some custom development, recovery, roms for your device?
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
SubwayChamp said:
Yes, so many time
When device is booting, it stays in bootlogo or goes atleast to bootanimation?
Click to expand...
Click to collapse
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
SubwayChamp said:
I understand that you tried with Sugar tool with no lucky.
Click to expand...
Click to collapse
Yes. After recognizing it keeps trying to download data but no luck.
SubwayChamp said:
Did you try again through SP Flash tool? trying to flash in a first attempt only preloader file and in a second attempt the other files? (try with 2 or 3 versions and see the differences).
Click to expand...
Click to collapse
I know it is disappointing!. I try this but no luck.
SubwayChamp said:
Is there some custom development, recovery, roms for your device?
Click to expand...
Click to collapse
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
SubwayChamp said:
I think that now you are flashing correct rom through fastboot but like you did before bad/wrong flashings your bootloader is refusing to boot to system. Flash through fastboot all the partitions that you can follow the syntax for every one of them by i.e. typing fastboot flash cache cache.img and so on one by one (some of them are unflashable through this method)
Click to expand...
Click to collapse
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
EFAYSAL said:
Unfortunately, nothing happens. The screen is black no bootlogo appears or anything that shows that device is booting. It is looking like nothing has happened.
Yes. After recognizing it keeps trying to download data but no luck.
I know it is disappointing!. I try this but no luck.
Unfortunately no, all that I found are TWRP recovery Roms. I don’t know if I can use them with SPFLASH Tool.
I began lose hope that the mobile could work again. I live in Sweden and no technicians kan help me to fix this issue. I should do it by myself.
If you kan help me to do that step by step. Please write to me what I have to do from the beginning step by step until I reach the end. To be sure I'm doing it by the right way.
Thanks
Click to expand...
Click to collapse
I´ll tell you some ideas with no any specific order that you can try or see if works.
Really very strange that display stays in black, you told me that flashing files through fastboot is working but doesn´t appear not even bootlogo, connect to pc as it is and see how pc recognices in devices manager and my pc if appears like a determined drive d/e/f so it looks that some bad flashing burn your kernel and this case is similar to when a Samsung device need to use jtag method to revive, if in your country no-one knows about Alcatel devices this could be a similar case to what I´m saying then it could be a clue for a technician. I tell you this cause many time ago when I flashed by error a Samsung s4 and only this method revived my device.
Try this, flash your stock recovery only through SPFlash tool and flash after through Alcatel Download tool your stock rom cause some firmwares need to detect stock recovery first to can flash other partitions.
At this stage don´t you have stock recovery, no? so you can try to format data cause sometimes when bootloader is altered then avoid to boot and formatting data can solve this.
If this recovery twrp is for your device you can try flashing through SPFlash tool, you have to put recovery.img and scatter-txt in a same folder. then if succesfull format data, system, wipe cache and dalvik and maybe later try to port some custom rom would be a way to solve this.
To flash any partition through fastboot this is the syntax, just follow one by one any of the files that are in your rom folder so just follow these, if some of then can´t be flashed don´t worry then it´s not flashable:
fastboot flash boot bot.img
fastboot flash cache cache.img
fastboot flash lk lk.bin
and so on till the end
...But after try this if you didn´t get boot to recovery and obviously you can´t delete data nor system then delete first the next partitions trough fastboot typing:
fastboot erase system
fastboot erase cache
fastboot erase userdata
fastboot erase boot
Try all this and let us see how it goes
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
EFAYSAL said:
I have flashed TWRP Rom but it is same , no luck.
On sugar tool I got this message after success flashing via SPFLASH tool.
View attachment 4518365
I tried all possible buttons to connect device to PC on Fastboot mode but the PC cannot send data to my device.
To be in Fastboot mode , the device has to boot while pressing on (PWR & VOL+) but my device can’t boot.
Click to expand...
Click to collapse
I see that Sugar tool detects your device like rooted and refuses to flash anything, compare imei number which is in the box, I hope that it couldn´t be changed.
Don´t tell me simply no luck, what it says in SPFlash tool when you tried to flash TWRP and I guess that you put scatter-txt and twrp renamed recovery.img simply in the same folder. Just to be clear, to can flash with this tool your device it has to be off not needed fastboot for this. (provide some screenie)
Other combination of keys to enter to fastboot to flash some partitions when something is missing is, try these three ways:
- Pressing only vol down and at same time connecting to charger (connect first one terminal of cable to your device and then to the charger)
- Pressing the three buttons till a menu appears (you must to release inmediately all)
- Pressing vol up + pwr till a menu appears (you must to release pwr button inmediately) then choose fastboot
In the post 4 I provided a link from Google Drive, in this zip there are 8 items;
- From the item 2 use this version of SP Flash tool, put the four files in a folder and flash them
- In the item 3 you will find some scripts for fastboot, maybe they´re working better and also you have here a subfolder with twrp image.
- And if you get sucessfully install twrp in the item 7 there is a backup with some files to restore from this recovery.
Try one by one and update the info, I hope that your motherboard is not damaged.