So i was having a read through of http://forum.xda-developers.com/z3-...ess-charging-case-t3100338/page4#post66363363 and i was inspired to do something similar, minus the soldering as i intend to sell my z3 when my contract expires and move onto a Samsung Galaxy s7 Edge.
The idea i've had was to use a similar wireless charger as the OP in the post above, but to use Conductive Copper Tape to go from the 2 magnetic charging pins to connect to the cables from the wireless charging pad, however i just want to confirm, from the picture in the original post i'm presuming that red would be positive and white would be neutral, however looking to confirm this, if the phone is standing vertically upright in the correct orientation, is the bottom the positive connection for magnetic charging and the top the ground?
Any help would be greatly appreciated
Related
The Nexus 5/7 has Qi charging built-in and will stick to the magnetic Nexus Wireless Charging Pad.
I have seen this for the Note 3 that will add Wireless charging: http://www.amazon.com/dp/B00GMRXD9U/
and this magnetic car dock that comes with a metal plate: http://www.amazon.com/dp/B00DPMNNUO/
Is it possible to add both to the Note 3 without changing to a thicker battery cover?
I would like to know also. Can anyone advise? Thanks in advance..
I just spoke to another user via PM.
Apparently the nGroove Snap holds the phone pretty well using just the official Samsung Wireless Charging Cover, without an additional metal plate. Looking at pics online, i can see that there's some more metal in that cover, maybe that's why it works.
I had also read about people putting the metal plate behind their batteries - but I have no idea how thick it actually is.
The second one is good.
anyone knows of a similar pass through coil in Uk, i mean ebay UK or amazon.
The magnetic charging docks are not bad. Also, the qi charging case from Sony is pretty nice. However, the best case would be a plastic case with a Qi wireless coil inside with a lead that wraps around and fits over the magnetic contact. Qi chargers like the Tylt work really well and they are so handy at home and in the car. I wear a holster so the flip cover is not necessary.
Sent from my D6503 using XDA Free mobile app
rambo6 said:
The magnetic charging docks are not bad. Also, the qi charging case from Sony is pretty nice. However, the best case would be a plastic case with a Qi wireless coil inside with a lead that wraps around and fits over the magnetic contact. Qi chargers like the Tylt work really well and they are so handy at home and in the car. I wear a holster so the flip cover is not necessary.
Sent from my D6503 using XDA Free mobile app
Click to expand...
Click to collapse
Can you please tell me where you managed to get the Qi charging case? I cannot find it anywhere...
matthieup said:
Can you please tell me where you managed to get the Qi charging case? I cannot find it anywhere...
Click to expand...
Click to collapse
Sony Cancelled the accessory.
They also removed any trace of it on their official websites.
HussainQ said:
Sony Cancelled the accessory.
They also removed any trace of it on their official websites.
Click to expand...
Click to collapse
I know, that's why I asked if maybe there are some prototype floating around
I did not mean to infer that I had one of the Sony Qi charging cases. I may have purchased one had they been available. I prefer the a slim fitting tpu or hybrid case. However, none that I have found fit correctly. Sony's magnetic charging docks are great and work fast, but one has to remove his case to use them. Yet no one makes a good case that covers up the SIM/Micro USB cover and exposes the magnetic charging area. This is totally stupid. One only seldomly changes his SIM and needs access to the micro usb port, but one always needs to charge.
If Sony is not going to add a Qi charger in the phone, they should at least make some good folio and slim fit cases at a sub $50 price that can be left on while charging using the magnetic dock.
Also, charging with a car dock is a pain without Qi charging using the Z2. The buttons are all in the wrong place also and interfere with the sides of both my car docks.
It's a real shame that Sony has not made a better attempt at charging options combined with cases. The Sony Z2 is a great phone. Even better yet woukd be a removeable battery. This is the only feature that keeps me going back to Samsung.
Sent from my D6503 using XDA Free mobile app
I have been thinking about trying this. I have dismantled a magnetic charger and there are only 2 wires in there. Positive and negative. Is there anything stopping me buying a universal micro usb qi adapter and soldering the positive and negative from that onto the positive and negative of the magnetic charger and hiding it all inside a case?
That's an interesting Idea. I've thought of the same thing, though I wanted to connect to the magnetic charger contact rather than the micro USB port. I'd like to make a case with a Qi charger and FM radio antenna built in. It wouldn't take up that much space.
I hope someone at Sony is watching this thread.
Sent from my D6503 using XDA Free mobile app
I for one actually feel a bit cheated.
The did announce Qi charging capability through a case and plate and while I had to choose between the S5/M8/Z2, this was one of the element that I considered...
Now all of a sudden they decide to cancel...
Though I would much prefer a Qi charger, the magnetic chargers can be useful. I bought some cheap magnetic charging cables and cut some of the plastic off them so they would work with my phone's case on. The magnets are weak and it s a pain to get them attached but of charges quite fast.
I was hoping that the Z3 would come out of the gate with wireless charging. In a statement made a few months back, they stated they would have Qi charging by the end of this year.
Hopefully the Z4 will have it. They also need to put 32 GB of internal storage in their phones.
Sent from my D6503 using XDA Free mobile app
If someone made a QI charging case, I'd be willing to pay for it, as long as it looked good enough!
might be worth testing out to see if the WCR14 connector and charging type works on a Z2. i can see the connector alone makes the phone look much bigger.
Why sony decided to put a magnetic charge on the side is beyond me.
Did anybody get any where with this? I am thinking about getting one of the coils on ebay for the samsungs and modifying it, they look very slimline as I suppose they are design to fit behind the battery cover?
I am planning to have it sit inside a TPU case I have. The difficult part will be the magnetic part / Soldering....etc
I wanted wireless charging, but the only one available (from fonesalesman.com) costs about $80USD to my door.
So, I bought an S5 pad and used some copper tape I had lying around. NOTE: Copper tape (or at least the one I have) is only conductive on one side because of the adhesive. I rolled the ends up to make large contacts for the terminals on the phone and wireless charging pad.
I also removed the golden pins from the wireless charging pad because they were a bit thick. If you do this, be careful not to remove the silver pad underneath (I almost did).
See pictures attached, they're pretty explanatory.
The current pad I am using is a bit thick, and have ordered a new one, but it works! And it doesn't cost the earth.
Hope this helps people.
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
How does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
killbom said:
how does it look with the back cover on? Im thinking about doing this with the extended battery. Since there is some room available to the left it might fit better? Can you take a picture from the side so that one can see how thick the charger thing is?
Click to expand...
Click to collapse
hi res picture 3mb
Thumb:
Hey guys,
It doesn't look as good as the post from DimonVideo, but as I said, I'm waiting on a thinner wireless model.
I'll put some pictures up later when I get home.
0.5mm Receiver
novastorm17 said:
Also, see attached the wireless charging pad I got.
It works, but its thick.
If anyone has some thin wireless charging pads, please recommend.
Click to expand...
Click to collapse
I'm planning on getting this one.
Can't post the link to amazon as I do not have the minimum posts to do so.
Search this:
Alpha SlimPWRcard - 0.5mm Qi Receiver for Samsung Galaxy Alpha with integrated NFC coil
Those are the only model available for the Alpha. But since I don't live in USA, it would cost at least $50USD for me. So, I put together this thing
Where you get the pinout of the alpha wireless charger?
Hey guys!
Thought I would post a review for this Qi wireless car charger since I didn't see much info about it and help those in deciding one for their car.
I have been using this Qi wireless car charger for about 4 months. The weather here is summer now so the car interior does get super hot, and so far this charger has been working like a champ in the heat.
The charger comes with a bunch of accessories which include:
-Vent adapter holder
-Traditional suction cup stand holder for dashboards
-Micro Usb cable
-Usb car chager (1 input)
-Sticky pads for wire management
I used the suction cup on my dash since my vents in my car are not ideal for my setup. The Qi charger is made hard sturdy black plastic and the section where you place your phone is made of a softer grippy rubber that holds the Nexus 6 very well. There is button on the back that release the two arm clamps. The Nexus 6 being a big of a device I thought it would be a tight fit, but I am happy to report that there is plenty of space. I have a Caseology Case and still a bit of extra room on the dock. So for those with thicker cases than mine can still fit, but in terms of it charging through a thicker case is something I do not have to test, but for those familiar with my case which I will put a link on the bottom of this post, my phone charges perfectly fine with it. Also the Qi charging unit in this has a 3 coil system so placement is not an issue and wireless charging is maximized and efficient as possible. There is a LED light on the bottom that indicates if it idle or charging, Green means idle and Blue means charging. The cradle of the charger is very sturdy and holds the Nexus with ease, have not had it drop my phone (yet) and hopefully stays that way. I use the charger everyday for the past 4 months and yet to encounter an issue, remember I am using it 95 degree weather for the past 4 months and it has not died on me yet. Once winter comes I will update on how it handles the cold, hopefully like a champ as it does in the summer! I attached some pictures for everyone to have a better look at it. Overall I am very happy with this charger and highly recommended!
Any questions about this product let me know and I will try my best to answer and help!
Amazon Links:
Qi wireless charger:
http://www.amazon.com/RAVPower-Wire...id=1440909770&sr=8-1&keywords=ravpower+qi+car
Case:
http://www.amazon.com/Caseology®-Me...=1440911291&sr=8-1&keywords=nexus+6+caseology
Thanks!
Look.like so good.
Can you try in front window and let us know how it works? When I get my phone it's going to be a window mount and since I'll have to use an OTG adapter for long distance that means I'll have to use wireless charging.
thunderstruck! said:
Can you try in front window and let us know how it works? When I get my phone it's going to be a window mount and since I'll have to use an OTG adapter for long distance that means I'll have to use wireless charging.
Click to expand...
Click to collapse
If you mean having the suction cup on the windows then yes it works even better cause the surface on the glass gives it an even better grip.
Hello,
Im lokking for the case that does it all. That you can use on a magnetic car mount and also on a wireless charger stand.
I bought these one, https://store.exelium.net/en/galaxy-s8/189-galaxy-s8-wireless-charging-case.html
And it does all of that perfectly, but the case it self i dont like it because it feels and is slippery on the hands.
Do you know of something similar? or have any recomendation?
Thanks.
I just bought this:
https://www.ipitaka.com/collections/aramid-case-for-samsung-galaxy-s8
I can confirm that wireless charging works with the case on. I also just ordered the magnetic mount, just waiting on it to arrive.
edit:
Here's a post with pics:
https://forum.xda-developers.com/showpost.php?p=72532053&postcount=4
I don't think any wireless charger will work through the little piece of metal needed for the magnetic stand/holder. If you find a way, please let me know.
AJ4VS said:
I don't think any wireless charger will work through the little piece of metal needed for the magnetic stand/holder. If you find a way, please let me know.
Click to expand...
Click to collapse
The Pitaka case works with wireless charging and magnetic mount. I think the metal in the case is shaped like a ring which allows wireless charge to pass through.
Slightly off topic. Has anyone been able to find a good wireless charger for the car? Air vent chargers have unsightly cables in the car which I really tend to avoid. What I would ideally like is a wireless charger that is like a cup holder style, has a sticky pad on and is quick charge compatible.
I just dont get why there is a gap in the market for something like that.
Once again, wishlist:
1. Cup holder style wireless charger
2. Sticky pad so that the phone stays in place (Can consider magnetic as well, but will need a case with that)
3. Quick charge
4. Hide wires somewhere