I've ordered two devices so far, each came with a different charger. Mine came with USB-C on both sides, the one for my son came with USB-C on one end, 'older' non-reversible USB on the other.
Mine seemed to stop working, when I tried to charge the phone on a train ride and I was mightily pissed because good chargers are hard to get.
Didn't have a matching dual USB-C cable at hand, to check if it was a charger or cable issue, but it sure wasn't a phone thing as my son's charger worked just fine.
Eventually I tried again one day and--loo--it just worked. Reversed and bent the cable at the phone side to check for an intermittent fault: No change. Reversed the cable at the charger side and--yes!--that's the source of the issue: Evidently the USB-C connector at the charger side isn't reversible...
Still shaking my head while I'm typing this, but glad I didn't have to hunt down a new charger or cable!
I have the regular USB (charger end) to USB type C one. The last few days it has been playing up. Left it charging to find that it had reached around 70% then stopped. Unplugged and then tried again on a different socket - nothing. Tried with a different cable on a different phone - nothing. Left it a while then tried it again - worked. Disconnected, reconnected - nothing. Since then it has seemed to work after it has been left alone for a while, but not if disconnected then reconnected. Odd.
Related
Hi,
I'm getting some problems charging my Hero. As of last night, it's stopped taking any charge when connected to the mains (with the supplied USB cable and 3pin plug usb adaptors).... although when I connect it to my laptop, it seems to charge?!
It worked with both without issue until last night... although I do typically charge it at work via usb (except weekend, hence why I only noticed it last night).
Has anyone experienced a similar issue and know of any way to fix this?
Thanks,
Brian.
I've also tried both charging methods while the fone is switched off.... and it behaves the same way.
:-(
have you tried another charger? maybe an older style HTC MiniUSB charger (if you have one), cos it sounds like your charger's died.
Did you use the same cable for both methods (the supplied one with mains adaptor) if you did and it worked via pc/laptop then you would guess the mains adaptor has died.
I would say that your charger is dead. Power supplies on them blow sometimes, maybe from power surges, maybe they're just made poorly.
Try another charger.
Try unclipping and reclipping the pin plate. The interchangeable pins sometimes come loose.
Hey all, the Sprint Hero comes with a charger that uses the usb cable to plug in to the phone. My problem is two-fold:
First, I like having a usb cord on me to charge where ever I go, and I don't like/am bad at remembering to take the usb cord out of the wall unit and pack with me in the morning.
Second, The usb cord isn't very long for a device that's plugged into an outlet near the ground (read: nearly every outlet in existence) and the usb cable barely reaches my desk for the phone to rest on.
Is there a decent charger that doesn't need our usb cable and has a couple extra feet in length? I don't want to get a universal charger because I don't want to fry the phone's charging system, which happened to my old Vogue. Everything I have found online is a universal type charger.
Has anyone had any experience with a good wall charger for the hero?
Thanks,
- JustPyro
You are aware that a standard USB cable works with the Hero? No need to use the one that came with the phone.
Regards,
Dave
Buy a longer USB-miniUSB lead, plug that into your home charger, and then carry the shorter one that HTC supplies around with you.
I've also found the stock one too short so I got a longer one, I also got a 3 inch long one to keep with me for tethering at work.... fits in my pocket nicely and it doesn't need to be any longer when the phone is sat next to my laptop.
These days I rarely find anywhere where I can't quickly borrow a miniUSB lead to charge my phone, they're used on so many different devices. Oh, and don't be afraid of 'universal' chargers - the Hero works with these fine, since USB is a 'universal' standard and 5v is 5v no matter where it comes from.
Hi I want to ask for help. I bought my htc touch pro 2 T 7373 from ebey but only phone with no charger.I bought HTC Power Supply model: TC P300 output: 5V-1A LPS Pin 1+ , Pin 4- .When I put it to charge , phone indicates to charge ,but battery does not charge.Battery is new and I dont think the problem is it.I want to ask you if this charger is compatible with HTC TOUCH PRO 2 T7373.
russslannn said:
Hi I want to ask for help. I bought my htc touch pro 2 T 7373 from ebey but only phone with no charger.I bought HTC Power Supply model: TC P300 output: 5V-1A LPS Pin 1+ , Pin 4- .When I put it to charge , phone indicates to charge ,but battery does not charge.Battery is new and I dont think the problem is it.I want to ask you if this charger is compatible with HTC TOUCH PRO 2 T7373.
Click to expand...
Click to collapse
Just use a miniUSB cable and plug it into your computer. Any USB wall charger should work. I've used iPhone USB chragers with a miniUSB cable, Nikon camera chargers, as well as a Motorola one. You just need to plug it into any USB port either on a wall or on your computer. Leave the device off while it charges overnight.
Problem with charged
I use both ways but no result , phone indicates to charged but battery not charging.Charger is original and consists of two parts: the charger and mini usb cable .When i run it sometimes on the displays show this message : The charging current is not enough for device power consumption.Please shut down unused applications , or switch to AC adapter. And I do not use any applications. I tried to load phone in the off position , indicates that the charger is ON but the battery is not charging .Please help if someone has the same problem
russslannn said:
I use both ways but no result , phone indicates to charged but battery not charging.Charger is original and consists of two parts: the charger and mini usb cable .When i run it sometimes on the displays show this message : The charging current is not enough for device power consumption.Please shut down unused applications , or switch to AC adapter. And I do not use any applications. I tried to load phone in the off position , indicates that the charger is ON but the battery is not charging .Please help if someone has the same problem
Click to expand...
Click to collapse
Try it with a different miniUSB cable. If you don't have one handy, miniUSB cables go for pennies on Amazon or eBay. You can find them in retail stores for about 10 dollars or so as well. If the cable isn't the problem, then it is either a problem with the charge port on the device, or the battery. It's far cheaper to trouble shoot the cable, so let's just start with that.
Sound like the charger is insufficient power, even though it says 1A. Try charging from a computer USB port and see if it charges. HTC don't list TP2 as suitable for this charger.
I am also facing same problem. LED shows charging but phone does not charge. And when I insert charger "USB TO PC" page shows up, Like I have connected the phone to PC.
Please Help...
I just had an issue charging which turned out to be an easy fix.
The led would come on and the icon would show charging but it wasn't increasing the battery %. Then I would get a message about the power not being enough and to plug it into a charger. I tried several chargers and was getting the same thing happening. I blew a few puffs into the charging port which looked clean and it was still happening. I wiggled the cable/plug in the port and occassionally the charging light would go on and off. The charging led even started to go on and off with the phone just sitting still on my table. I feared that my charging port had gone bad so I ordered 2 spare batteries and battery charger from ebay for $10 (works well and battery life good).
While waiting for the ebay purchase to arrive I did some reading up and saw that pins could be bent etc. In my fustration I used a pair of tweezers to gently scrape the charging port pins/contacts (in a straight direction). Then I used an old toothbrush and firmly brushed out the usb port - a whole bunch of lint and stuff come out of the port even though it had previously looked clean.
I plugged in my charger and bingo! My charging issue was gone.
ukexport said:
I just had an issue charging which turned out to be an easy fix.
The led would come on and the icon would show charging but it wasn't increasing the battery %. Then I would get a message about the power not being enough and to plug it into a charger. I tried several chargers and was getting the same thing happening. I blew a few puffs into the charging port which looked clean and it was still happening. I wiggled the cable/plug in the port and occassionally the charging light would go on and off. The charging led even started to go on and off with the phone just sitting still on my table. I feared that my charging port had gone bad so I ordered 2 spare batteries and battery charger from ebay for $10 (works well and battery life good).
While waiting for the ebay purchase to arrive I did some reading up and saw that pins could be bent etc. In my fustration I used a pair of tweezers to gently scrape the charging port pins/contacts (in a straight direction). Then I used an old toothbrush and firmly brushed out the usb port - a whole bunch of lint and stuff come out of the port even though it had previously looked clean.
I plugged in my charger and bingo! My charging issue was gone.
Click to expand...
Click to collapse
That was the biggest problem with MiniUSB was the width and height of those ports. It's a haven for stray dust and dirt. They need to be brushed out every so often, especially when you just drop it in you pocket.
hi buy and it schould work
buy a new charging cable
ukexport said:
I just had an issue charging which turned out to be an easy fix.
The led would come on and the icon would show charging but it wasn't increasing the battery %. Then I would get a message about the power not being enough and to plug it into a charger. I tried several chargers and was getting the same thing happening. I blew a few puffs into the charging port which looked clean and it was still happening. I wiggled the cable/plug in the port and occassionally the charging light would go on and off. The charging led even started to go on and off with the phone just sitting still on my table. I feared that my charging port had gone bad so I ordered 2 spare batteries and battery charger from ebay for $10 (works well and battery life good).
While waiting for the ebay purchase to arrive I did some reading up and saw that pins could be bent etc. In my fustration I used a pair of tweezers to gently scrape the charging port pins/contacts (in a straight direction). Then I used an old toothbrush and firmly brushed out the usb port - a whole bunch of lint and stuff come out of the port even though it had previously looked clean.
I plugged in my charger and bingo! My charging issue was gone.
Click to expand...
Click to collapse
I was facing the same charging problem and was looking for a solution. And i found this forum and read it and did the same thing and my problem is fix.. I can charge my mobile now. Thanks a lot for the great help.
Sarchy Minimum
All of these dumb charges, ie bricks in the wall, use the unused USB pins to communicate how much power they can provide. There are some resistors they put on the D-/D+ to say this is a 700ma charger or whatever. Trouble is that there are limited standards on these resistors so it's more than possible that a phone will charge but not enter high current charging when attached to a new brick in the wall. The cables however are more universal.
C series serial number prime worked for three days now won't take a charge. Device will connect to pc or mac via cable, just won't take a charge. Any ideas for me?
askmattrix said:
C series serial number prime worked for three days now won't take a charge. Device will connect to pc or mac via cable, just won't take a charge. Any ideas for me?
Click to expand...
Click to collapse
there have been other threads about this. usually its the charger overheating and putting it in a ziplock in the freezer, resets it.
Mine did that too, just leave the charger and everything unplugged from the wall for a day. That fixed mine.
Sent from my ADR6425LVW using XDA Premium.
The other issue I've seen is poor contact in the USB socket on the wall adapter. I had to unplug the usb cable from the wall adapter. Then, look at the usb socket on the power adapter. The gold pins are the usb contacts. Directly opposite of them, there should be two silver prongs. I had to use a small flat blade screwdriver to pry both of them out a little further to ensure they did their job of firmly pushing the usb cable against the socket's usb contacts. Once I did, my TF201 was able to get charge from it, again.
If you decide to replace the wall charger, I believe Fry's and Office Depot stock the asus charger.
Same thing for me.. PC recognizes it as a media device, but will not charge with wall charger. Wall charger works with my HTC Phone, so it works.
I don't think it has anything to do with the latest update, since the Dock wont charge either, and there's no OS in that, right?
Just experienced this today. I have had it unplugged for about 10 hours now, we'll see if it charges.
I had the same issue few days after I got my prime. I connected my sgs to the charger and it worked. Then connected the prime and voila-works.
askmattrix said:
C series serial number prime worked for three days now won't take a charge. Device will connect to pc or mac via cable, just won't take a charge. Any ideas for me?
Click to expand...
Click to collapse
Which C model do you have? C1,2,3? Just asking.
Johnny0906 said:
Which C model do you have? C1,2,3? Just asking.
Click to expand...
Click to collapse
C1. There are some good suggestions here I need to try.
Wrap it in a towel and bang it against a table. That will fix it usually. Then get some pc heatsinks and some arctic silver adhesive and you can attach them to the charger to keep it from happening again.
The plug has two options, 5V (standard for USB?) and 15V. I used the plug on my old HTC phone (Ozone) and then plugged it back into my Prime and it worked. Thanks for the great tips guys.
Since the charger works in two modes, I wonder if some charges became confused and started dishing out 5V when they should be dishing out 15V. Thoughts?
G37 said:
The plug has two options, 5V (standard for USB?) and 15V. I used the plug on my old HTC phone (Ozone) and then plugged it back into my Prime and it worked. Thanks for the great tips guys.
Since the charger works in two modes, I wonder if some charges became confused and started dishing out 5V when they should be dishing out 15V. Thoughts?
Click to expand...
Click to collapse
Hi, I got the same problem. The charger indeed seems to be stuck in the 5V mode, since, when plugged in the tablet does get charged, even though it is not indicated, but very slowly. It is charging as if it is plugged in to a pc.
I tried plugging it into (old) phones, but I still can't seem to get it to switch back to the 15V mode.
The freezer didn't help either.
Any other suggestions?
I waited about 4-5 hours before plugging into my old phone. My other suggestion is to allow the phone to charge for a short bit (30 minutes) unplug and wait, then plug into your Prime.
I have a feeling that its a transistor toggle that isn't flipping at the correct voltage.
I've had the same problem yesterday. In my case the problem was with the charge socket on the keyboard itself. Some copper pins were deformed and that stopped the device charging. I took a magnifying glass(also for checking if any of the copper pins are bend) and a small tool to bend them back. After this it charged again. Hope this helps.
My charger suddenly stopped working from today. The Prime is detecting the connection as the screen turns ON but it is not charging. I charged my sensation using the same adapter and USB cable and it is working fine. Why can I not charge Prime via PC like phone? Is it possible? I am in India and not sure if the power adapter is easily available as Prime is not yet launched in India.
Kindly suggest.
Thanks in advance.
Hi,
I've started to have this problem today, plug it in and it does come up with the charge icon but it doesn't charge - or doesn't seem to.
However I left it connected last night from midnight until 8am this morning and it went from 13% to 17% so it is charging VERY VERY slowly although the unit doesn't actual seem to think it is.
I have it plugged in to my phone right now and its working perfectly, I borrowed the charger to my g/f last night to charge her iphone and i'm thinking this might have done something to flip the voltage as since then it isn't working.
Anyone have any ideas on this??
Kevin
thornd7 said:
The other issue I've seen is poor contact in the USB socket on the wall adapter. I had to unplug the usb cable from the wall adapter. Then, look at the usb socket on the power adapter. The gold pins are the usb contacts. Directly opposite of them, there should be two silver prongs. I had to use a small flat blade screwdriver to pry both of them out a little further to ensure they did their job of firmly pushing the usb cable against the socket's usb contacts. Once I did, my TF201 was able to get charge from it, again.
If you decide to replace the wall charger, I believe Fry's and Office Depot stock the asus charger.
Click to expand...
Click to collapse
I had this problem a couple of weeks ago and completed the same as above works well
Gilbo12 said:
I had this problem a couple of weeks ago and completed the same as above works well
Click to expand...
Click to collapse
But if the charger works fine when charging a phone it cant be the connection at fault..
It does seem to me that the power it is outputting has dropped especially the I managed to gain 5% over the course of a night where WIFI was off and screen was off even though the charge icon doesn't come up.
Is there a way of forcing the charger back in to 12v mode??
damnit... I had the same problems a few days ago and I thought it was in the cable instead of the charger... not realising the charger has to put out 15v instead of 5v.
Does this mean the Transformer won't charge with for example, my HTC charger?
I totally messed up my cable, because I thought it was broken... when I opened up the USB plug, I noticed the yellow wire was not connected anymore, but this didn't solve anything. Eventually I messed up the cable that bad, that I've ordered a new one from ebay... but when I read this... I should have just banged the charger a few times... shait.
funfair said:
damnit... I had the same problems a few days ago and I thought it was in the cable instead of the charger... not realising the charger has to put out 15v instead of 5v.
Does this mean the Transformer won't charge with for example, my HTC charger?
I totally messed up my cable, because I thought it was broken... when I opened up the USB plug, I noticed the yellow wire was not connected anymore, but this didn't solve anything. Eventually I messed up the cable that bad, that I've ordered a new one from ebay... but when I read this... I should have just banged the charger a few times... shait.
Click to expand...
Click to collapse
Has anyone actually ever managed to fix this problem? I've just contacted ASUS about it to see what they say - hopefully they'll ship me out a new charger plug or something, what a useless charger!!
I've been having a charging issue for a month or so, I'm not sure what to think about it.
Let me explain quickly, that I don't like to fill my pockets with micro usb cables or AC chargers whenever I go out. As such, I usually just acquire a few extra chargers or usb cables and just leave them where I am most likely to need them. I'm sure this is common.
Charger 1 : Samsung AC charger, came with phone. Lives by my bed.
Charger 2 : Blackberry AC charger, acquired from work. Lives in kitchen.
USB 1 : $1 cable from Amazon. Lives in the car, plugged into 12vDC lighter to USB adapter.
USB 2 : $1 cable from Amazon. Lives on my desk at home. Plugged into PC.
USB 3: Blackberry cable. Found at work. Lives at office.
On to the problem.
Somehow, Charger 1, USB 1, USB 2 seem to drain my phone. If I plug in to charge overnight and power is at 45%, when I wake up, I'm at 12% or some other number. Battery App indicates that it has been "charging" I could unplug and replug the charger a few times and then monitor the charge level, if it drops, I unplug and replug again, reboot phone perhaps, it may or may not fix the problem. Problem has gotten worse and these no longer seem to charge phone.
Charger 2 seems to have worked more consistently, but not always. Seems to have gotten worse.
USB 3 is the only cable that consistently charges without problem. It is a blackberry branded cable, much lower gauge wires (read: thicker) than the cheap $1 cables from Amazon or the Samsung OEM charger.
I've tried charging with phone off, does not seem to make a difference.
I'm running Doc Masters v6, problem was also present in v5. Since issue is same with power off, I don't believe this is a ROM issue and have not tried Odin to stock.
Is this sign of the USB port going out? Anyone tried to replace/repair microUSB or have similar experience?
About the part about replacing a microUSB port, I had to do this because my connection was getting flaky, then I messed it up altogether. I sent my phone to MobileTechVideos and they sent it back to me with the port replaced.
I may try sending it to repair. Sounds like a pretty reasonable price and quick turnaround. Dunno if I can take going back to my G1 for a week while I wait though.
Provided I don't misplace the only USB cable that will charge my phone, I should be ok for a while.