Hi!
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. I followed all of the instructions on the ulefone-s website. When I started the flashing process I got a message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
Duplicate:
https://forum.xda-developers.com/android/help/sp-flash-tool-problem-brom-error-t3531265
Thread closed.
Related
Hi all,
please help me out because I'm desperate.
Yesterday I received a THL W8 mobile phone and I flashed it with the ROM reported on this thread.
Once done, my SD card wasn't recognized by the phone, so I decided to flash the same ROM again.
Unluckily, my bad, I didn't uncheck the PreLoader tick and as result now the phone doesn't boot at all.
The PC recognizes it and the drivers are ok, but when I try to flash a ROM, any ROM, I get different errors.
With SP Flash Tools version "SP_Flash_Tool_v3.1304.0.119" the bottom bar fills red fully (100%) but after about 40 seconds it gives me the following error:
S_FT_ENABLE_DRAM_FAIL (4032)
With the SP Flash tools version "AntiBrick_Flash_Tool_v3.1224.0.sn85" 3 seconds after the bottom bar gets filled in red, the following error is returned:
SP FLASH TOOL ERROR: (8200)
[Platform Error] The load and target are inconsistent!
I've also tried to flash the stock ROM but with the same bad results. More, I tried to do a reset with both the aforementioned Flash tools versions with success, but after that whenever I try to flash the phone with any ROM, I get the same errors as before.
Since the PC recognizes the phone I'm kinda sure it can be restored, but apart what I tried already, I'm out of ideas.
Any help is welcome
Thank you guys
Cheers
Heide
really? no one really answered the poor guy, the phone ended up bricked for good after all
hi friends i am new at this forum and need some help, before this, I usually figured everything out by reading others thread or googling. But now I need your help guys. I recently try to flash my i ball cobalt 4 with the stock rom of the same version [downloaded from needrom.com],But I probably did a mistake and I was messing up with bootloader. The result is that my phone wont even start. No bootloop, no recovery, nothing. Display and everything else remains dead.
At least is phone still detected by computer when I connect it as mtk usb port[it is on META mode now i think]
Also in Smart Phone Flash Tools phone is still visible.
But when I try to flash or format anything it gives me this error message:
It says:
"BROM ERROR: S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM Failed!
[HINT]: Please check your load matches to your target which is to be downloaded"
I already tried different versions of SPFT and also stock cobalt 4's ROM's from diferrent sources.cleaned mtk deivers many times by using usbdeview according to tutorial. but sadly did not get any success.
My OS is Windows 7x64.
Please guys, this is the first time I'm asking for a help, because I am really desperate and I don't know what else try to make my phone flashable and working again. I googled, searched lot of topics, everything what I was capable to think about. I would be super gratefull for help.
THX guys for your suggestions and help!!!
BTW: I heard some phones can be turned to some kind of "service" bootloader mode with connecting two contacts on main board of phone. Do you know if iball cobalt 4 have this function?
one more thing is that when i selected scatter file first time in spft it gave me an error invalid scatter file so i had to delete scatter file's first line[ie birdtoolminver3.4].so is the scatter file is problem of mentioned error.
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. When I started the flashing process with SP flash tool I got this message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
hi i also bought paris x last year tried to flash it today using sp flash tool with official android 6 rom everything fine until i clicked download...
pmt changed rom - error #1
so then i looked up im supposed to switch to firmware upgrade but that resulted in error
s_invalid_bbchip_type - error #2
now my phone is bricked and whenever i connect it to my pc it appears for about 2 seconds and then disappears...
well im hoping that someone here could actually help cause this is really frustrating and i need to be able to use my phone next week... :/
thanks for replys
same probleme here
invalid bbchip type (0x3eb)
If anyone have this solution, Then please reply
I have also this type of problem In my Intex ace mini mobile
I also experienced problems like that, and couldn't solve it.... ERROR: S_INVALID_BBCHIP_TYPE (1003)
slekdor50 said:
I also experienced problems like that, and couldn't solve it.... ERROR: S_INVALID_BBCHIP_TYPE (1003)
Click to expand...
Click to collapse
Check the scatter, make sure that the line, i.e. matches the device chip type:
platform: MT6735M < -- is this correct?
peti2ty said:
I have a problem with my Paris X device. I had an unofficial rom and I wanted to flash the official one. When I started the flashing process with SP flash tool I got this message: "BROM ERROR: S_INVALID_BBCHIP_TYPE (0x3EB)"
Since that my phone is like dead. I cant switch on, I cant either flash again because my driver disappears in 2 seconds and I got the same error everytime.
Please help me, I would really appreciate it. :fingers-crossed:
Click to expand...
Click to collapse
I think this is scatter file mismatch, because I have done a proper read back of Inew L4 mt6735 to flash it to another phone with exact same model and build. But that flash file is not even working to flash that phone from which I made it giving this same error.
ERROR: S_INVALID_BBCHIP_TYPE (1003)
Still working on it.
[Update]
Only a single "m" in MT6735M in scatter file was missing, now its working all fine. :fingers-crossed:
I searched the whole internet for years to solve this error...
So if your getting this error better check your scatter platform names etc.....bcz even if you get it from readback or official flash files, like in my case it can give you error.
If you're getting this same error every time so try the above advice and here is a tip for early disconnection, connect while holding volume button or open yiu device and find kcolo[\B] and short it with GND.(better find details from google bcz i am too funding it)
Hello everybody, good evening
First of all, this is my first topic. So if I made something wrong, sorry.
Well, I have that problem, I try to flash a twrp in my Homtom HT 17 pro, but happen the follow error: "PMT changed for the ROM; it must be downloaded", searching in the web I found that tutorial youtube.com/watch?v=lIWgpoc9UEY[/url] I follow this but when try flash again the process was completed, but the smartphone is dead, no switch on, no charge, the smartphone is stopped nothing happen with he. When I try flash the stock ROM the follow error happen "BROM ERROR : S_FT_DOWNLOAD_FAIL (0xFA8)" searching on the web for this error the tutorials say for try with a different version of the SP Flash Tool (I using the version 5.1628), but the older version that I try (3.1224, 5.1516, 5.1524) can't recognize a scatter file that I downloaded with the stock ROM. So of all that someone can help me? Thank you since now. Please help me, I have no smart now thanks!
up
robertruiter2 said:
Hello everybody, good evening
First of all, this is my first topic. So if I made something wrong, sorry.
Well, I have that problem, I try to flash a twrp in my Homtom HT 17 pro, but happen the follow error: "PMT changed for the ROM; it must be downloaded", searching in the web I found that tutorial youtube.com/watch?v=lIWgpoc9UEY[/url] I follow this but when try flash again the process was completed, but the smartphone is dead, no switch on, no charge, the smartphone is stopped nothing happen with he. When I try flash the stock ROM the follow error happen "BROM ERROR : S_FT_DOWNLOAD_FAIL (0xFA8)" searching on the web for this error the tutorials say for try with a different version of the SP Flash Tool (I using the version 5.1628), but the older version that I try (3.1224, 5.1516, 5.1524) can't recognize a scatter file that I downloaded with the stock ROM. So of all that someone can help me? Thank you since now. Please help me, I have no smart now thanks!
Click to expand...
Click to collapse
Hi!
If I am not wrong You hard bricked the phone so you won't be able to use it anymore.
Hi guys, sorry I'm newbie so after a long time surfing for solutions, I couldn't solve my own problem. That's why I come here to ask for your supports
Firstly I unlocked bootloader, installed TWRP and rooted my device and enjoyed it. But after decided to wipe (factory reset) this phone with TWRP, and my problem began...
1. I got stuck in TWRP loop booting. After that I tried to fastboot system.bin, cache.bin and recovery.bin from Stock Firmware but it still hung at Nokia logo booting
2. I still kept trying with SP Flash Tool, Miracle Box but there was still no hope:
- SP Flashtool v5_1548 gave me error: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)
- Miracle Box 2.27A told me there was an error (i don't remember the code) occured in the location (i can't remember its code either)...
Anyone can solve it please help!!!! I love this phone much and as of now still suffering day by day since I can't do anything with it.
Kindly appreciate any suggestion and solution.
Thank you all!
Can you provide me the stock rom link please?
@you download firmware . Youtube : type "nokia ta 1066 flashing" GSM TEAM
@you flash this firmware , tick only recovery.bin
@notes : hold volume up & volume down -----> NO error: BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)
good luck ^_^_^//
@i'm using Nokia 1 Red TA-1047