I need to root my S5 to enable a 3rd party SystemUI tuner. I've tried several one-click rooting methods, but none of them seem to work. My device runs Android 6.0.1. I can provide any additional screenshots or specs if needed.
legomg said:
I need to root my S5 to enable a 3rd party SystemUI tuner. I've tried several one-click rooting methods, but none of them seem to work. My device runs Android 6.0.1. I can provide any additional screenshots or specs if needed.
Click to expand...
Click to collapse
Try reading: https://forum.xda-developers.com/tm...l/root-how-to-root-sm-g900t-firmware-t3358190
DickyG said:
Try reading: https://forum.xda-developers.com/tm...l/root-how-to-root-sm-g900t-firmware-t3358190
Click to expand...
Click to collapse
Will this cause me to loose my data?
DickyG said:
Try reading: https://forum.xda-developers.com/tm...l/root-how-to-root-sm-g900t-firmware-t3358190
Click to expand...
Click to collapse
of course I can help. the best way to do it is to install a custom recovery, my favorite one is TWRP. Then you grab your favorite custom rom and flash it from there. I also recommend picking something new but if you enjoy touchwiz there are plenty of nice touchwiz roms out there. Such as smallwiz version 1. do not install version 8 its very laggy and has a ton of bugs. But the best rom out there is resurrection remix rom for the s5. hope I helped !
RomBetaTester said:
of course I can help. the best way to do it is to install a custom recovery, my favorite one is TWRP. Then you grab your favorite custom rom and flash it from there. I also recommend picking something new but if you enjoy touchwiz there are plenty of nice touchwiz roms out there. Such as smallwiz version 1. do not install version 8 its very laggy and has a ton of bugs. But the best rom out there is resurrection remix rom for the s5. hope I helped !
Click to expand...
Click to collapse
Ok this did help, however i know extremely little about installing custom recoveries. So I need to know:
1. What will I need to do it
2. What are the steps to do it, and...
3. Will installing a custom recovery wipe my storage?
I'm sorry if I'm being irritating, but I'm only just about to start computer science as a freshman.
legomg said:
Ok this did help, however i know extremely little about installing custom recoveries. So I need to know:
1. What will I need to do it
2. What are the steps to do it, and...
3. Will installing a custom recovery wipe my storage?
I'm sorry if I'm being irritating, but I'm only just about to start computer science as a freshman.
Click to expand...
Click to collapse
I am sorry for the late reply my power was out due to a storm, Firs you need to install Odin, then you need to download TWRP, I recommend TWRP version 2.8.7.0 its faster even though the graphics look pretty bad. Next flash TWRP using AP on Odin, (Phone needs to be in download mode). On the Samsung devices TWRP wont install unless you do it twice so flash TWRP twice but the second time you flash unlick reboot on the options in odin. Once flashed a second time reboot into recovery, congratulations you have a custom firmware, now download your custom rom of choice I recommend small wiz its a debloated version of touchwiz, download it on your computer and then transfer it over to your phone on the download section after that you're going to want to wipe your wipe your phone. Wipe everthing except internal storage and sd card. next go to install on TWRP then navigate to the download folder click on Small wiz or whatever custom rom you have and then flash it. then once its done reboot and you're done. this will take a while to boot on the first time. its compressing a ram disk and installing a new kernel. dont be scared.
I am having issues rooting my device. I am running 6.0.1 marshmallow and with the march 1st, 2017 security patch. I am using a mac and am able to get odin v 1.85 running on my computer using wine bottler but for some reason when I connect it odin doesn't pick it up. I have reinstalled the drivers and it's still doesn't work. It works fine using Kies. I am not sure what I am doing wrong. Any help would be greatly appreciated or point me to the right thread thanks.
RomBetaTester said:
I am sorry for the late reply my power was out due to a storm, Firs you need to install Odin, then you need to download TWRP, I recommend TWRP version 2.8.7.0 its faster even though the graphics look pretty bad. Next flash TWRP using AP on Odin, (Phone needs to be in download mode). On the Samsung devices TWRP wont install unless you do it twice so flash TWRP twice but the second time you flash unlick reboot on the options in odin. Once flashed a second time reboot into recovery, congratulations you have a custom firmware, now download your custom rom of choice I recommend small wiz its a debloated version of touchwiz, download it on your computer and then transfer it over to your phone on the download section after that you're going to want to wipe your wipe your phone. Wipe everthing except internal storage and sd card. next go to install on TWRP then navigate to the download folder click on Small wiz or whatever custom rom you have and then flash it. then once its done reboot and you're done. this will take a while to boot on the first time. its compressing a ram disk and installing a new kernel. dont be scared.
Click to expand...
Click to collapse
I cannot install Odin on my computer, because my only computer is a Mac. My only method of installing TWRP without a computer was on my Galaxy Tab, which was already rooted, and I used Flashify to flash it. Since my S5 has no root, I can't flash TWRP with Flashify.
legomg said:
I need to root my S5 to enable a 3rd party SystemUI tuner. I've tried several one-click rooting methods, but none of them seem to work. My device runs Android 6.0.1. I can provide any additional screenshots or specs if needed.
Click to expand...
Click to collapse
Does your S5 run a stock room?
---------- Post added at 03:19 AM ---------- Previous post was at 03:16 AM ----------
If you have a computer watch this video. It allows you to root your S5 through Odin.
---------- Post added at 03:20 AM ---------- Previous post was at 03:19 AM ----------
RomBetaTester said:
Does your S5 run a stock room?
---------- Post added at 03:19 AM ---------- Previous post was at 03:16 AM ----------
If you have a computer watch this video. It allows you to root your S5 through Odin.
Click to expand...
Click to collapse
https://youtu.be/uPcEeMhlR_8
RomBetaTester said:
Does your S5 run a stock room?
---------- Post added at 03:19 AM ---------- Previous post was at 03:16 AM ----------
If you have a computer watch this video. It allows you to root your S5 through Odin.
---------- Post added at 03:20 AM ---------- Previous post was at 03:19 AM ----------
Click to expand...
Click to collapse
Yes. My S5 is running the factory ROM I bought it with.
I resolved the issue. I flashed TWRP using my school laptop and installed Lineage 14.1. I got root by flashing a file to enable it in settings.
I have to say, Lineage is a LOT faster than the stock ROM, and it looks a lot cleaner too. Thanks for the help guys
Related
First time rooting / installing rom quick question
Looking to flash phone to villianrom 3.0 from what i read on the 2.4 version older posting it says to root with CF-root first. In the new 3.0 version posting it says it includes Ninphetamine kernel and the instructions assume you have clockwork mod already and can install zip from sd, Do i still need to CF-root before running 3.0 or does the Ninphetamine kernel Root automatically from the 3.0 zip??
Thanks
You need first of all a kernel wit CWM then you can flash custom firmwares through it from a .zip-file on your sd.
The new version will bring root with it through the kernel but you are not able to flash it unless you have CWM if it comes as a .zip-file
So for the first time flash a rooted kernel that includes CWM through "Odin" and then you are free to flash anything you want through CWM.
Hope that answers your question.
brunobanane said:
You need first of all a kernel wit CWM then you can flash custom firmwares through it from a .zip-file on your sd.
The new version will bring root with it through the kernel but you are not able to flash it unless you have CWM if it comes as a .zip-file
So for the first time flash a rooted kernel that includes CWM through "Odin" and then you are free to flash anything you want through CWM.
Hope that answers your question.
Click to expand...
Click to collapse
Could this be a problem I am having
I have rooted my phone and copied villianrom to my sd card.
When I go through CWM and delete wipe does that also wipe my root?
When I try to install the ROM i keep getting error messages
Did you install the Ninphetamine kernel first...
No good complaining its not working if you skip steps....
What kernel did you flash to get CWM ?
Should all work fine if you follow the steps presented in the VillainRom post...
ultramag69 said:
Did you install the Ninphetamine kernel first...
No good complaining its not working if you skip steps....
Click to expand...
Click to collapse
Sorry I thought it was included in the ROM?
Sorry not that clued up on all this
---------- Post added at 08:31 AM ---------- Previous post was at 08:29 AM ----------
brunobanane said:
What kernel did you flash to get CWM ?
Should all work fine if you follow the steps presented in the VillainRom post...
Click to expand...
Click to collapse
I just flashed Frankensten kernal and downloaded ROM Manager from market
serpicoUK said:
Sorry I thought it was included in the ROM?
Sorry not that clued up on all this
---------- Post added at 08:31 AM ---------- Previous post was at 08:29 AM ----------
I just flashed Frankensten kernal and downloaded ROM Manager from market
Click to expand...
Click to collapse
im not to familiar with Frankenstein kernels. what you should of done is rooted first your phone with one of the CF kernels..do that through odin..that will get your phone rooted..once you do that then you can flash any rom you like but always follow the guide from the thread of the rom you going to flash
EDIT: if you flash CF-root your rooted..go to development original and go on the thread and follow the guide...its through odin if i remember well its been a while lol but once you do that you will have all the perks of been rooted...
once you do that download the rom you want and just flash away through recovery or CWM manager....but do your reading and back up your rom first before you do flash
Matriak31 said:
im not to familiar with Frankenstein kernels. what you should of done is rooted first your phone with one of the CF kernels..do that through odin..that will get your phone rooted..once you do that then you can flash any rom you like but always follow the guide from the thread of the rom you going to flash
Click to expand...
Click to collapse
I followed these instructions and flashed insecure Kernal then the it was actually this one after
GT-I9100_XXKI3_original
http://reviews.cnet.co.uk/mobile-phones/how-to-root-your-samsung-galaxy-s2-50004972/
Did you try flashig through RomManager or by booting the phone into CWM recovery?
---------- Post added at 09:46 AM ---------- Previous post was at 09:44 AM ----------
Hmm...give this approach a try.
http://forum.xda-developers.com/showthread.php?t=1103399
brunobanane said:
Did you try flashig through RomManager or by booting the phone into CWM recovery?
---------- Post added at 09:46 AM ---------- Previous post was at 09:44 AM ----------
Hmm...give this approach a try.
http://forum.xda-developers.com/showthread.php?t=1103399
Click to expand...
Click to collapse
I flashed the ROM through Android system recover (3a)
is that CWM recovery?
I managed to get villianrom welcome screen but it just keeped flashing for about 10mins and wouldn't reboot properly
---------- Post added at 08:51 AM ---------- Previous post was at 08:49 AM ----------
brunobanane said:
Did you try flashig through RomManager or by booting the phone into CWM recovery?
---------- Post added at 09:46 AM ---------- Previous post was at 09:44 AM ----------
Hmm...give this approach a try.
http://forum.xda-developers.com/showthread.php?t=1103399
Click to expand...
Click to collapse
Excellent
Thanks
So If I flash that Kernal and then install villianrom through CWM then it should work and still be rooted?
Nope that isn't CWM.
Jep, follow the steps for CF-root, then from the rom and then all will be fine and with root.
brunobanane said:
Nope that isn't CWM.
Jep, follow the steps for CF-root, then from the rom and then all will be fine and with root.
Click to expand...
Click to collapse
Once I have flashed the new ROM will I need to install i new Kernal or will it be included?
serpicoUK said:
Once I have flashed the new ROM will I need to install i new Kernal or will it be included?
Click to expand...
Click to collapse
it will be included
Now that you are rooted back up the rom first before you go ahead and start your journey of flashing...
Matriak31 said:
it will be included
Click to expand...
Click to collapse
Ok think I am getting it now, not sure why I am so stupid this time as I have rooted my Hero and Orange San Francisco first time around.
One last thing.
Is ROM Manager and CWM the same?
I have ROM Manager installed and my phone is rooted, can I not just flash the CF-ROOT from my sd card?
Instructions - If you already have CF-Root
- Copy the zip file to your SD card
- Stop sharing SD card with computer over USB, unplug the cable, etc
- Applications -> CWM -> Flash kernel. Select the ZIP file on your SD card.
- Done
I think RomManager is just an app that can flash roms, do backups and other things by using CWM.
But I'm not that familiar with Rom Manager so I don't know much about it.
As I said I don't know what things you can do with RomManager but I would flash the kernel with Odin, thats the save way.
For the instructions...I think that means if you have a previous version of CF-Root and already have CWM.
brunobanane said:
I think RomManager is just an app that can flash roms, do backups and other things by using CWM.
But I'm not that familiar with Rom Manager so I don't know much about it.
As I said I don't know what things you can do with RomManager but I would flash the kernel with Odin, thats the save way.
For the instructions...I think that means if you have a previous version of CF-Root and already have CWM.
Click to expand...
Click to collapse
So installing that Kernal will not cause any harm if my phone is already rooted?
No.
Even if it would you could just flash a stock firmware back again and start from zero.
brunobanane said:
No.
Even if it would you could just flash a stock firmware back again and start from zero.
Click to expand...
Click to collapse
Thanks for all you help
Another thing I have noticed is when I wiped my phone it reset itself as normal but all my media and photos where still there even though I copied them over to my sd card just incase, is this normal?
No problem.
Jep that is normal. It just wipes your system. If you want to wipe your phone of all your files and reset the system than you need to do it with a combination in the dialer. *2767*3855# but watch it...the process starts right after you insert the # no question if you really want to!
brunobanane said:
No problem.
Jep that is normal. It just wipes your system. If you want to wipe your phone of all your files and reset the system than you need to do it with a combination in the dialer. *2767*3855# but watch it...the process starts right after you insert the # no question if you really want to!
Click to expand...
Click to collapse
That's cool.
Dont want to just wasn't sure if it was working correctly.
Dont have anything to really back up so will do it all tonight once home from work
cheers
Have a good weekend
Hi !
I have just bought a Samsung Galaxy Tab 10.1 Wifi only (GT-P7510).
I want to install ICS on it, but I'm stucked on a problem : my screen is scrolling (flickering if you prefer, like an old broken TV) on a recovery and after install some roms.
My current configuration is OK with that :
- Recovery : CWM v5.5.0.4.
- Android : 3.2
- Kernel : 2.6.36.3 [email protected] #1
- Version number : HTJ85B.XXKL2 P7510XXKL2
With this recovery, I tried to flash my tab with the latest Krang version.
Installation OK but when Android starts : my screen is flickering and never stops.
I can see the Android ignition but impossible to use it except to shut down.
When I try to flash with Cyanogen mod for P7510 (plus.google.com/100275307499530023476/posts/1Lm5iULvf3w), my recovery says :
Assert failed: getprop("ro.product.device") == "p4wifi" II getprop("ro.build.product") == "p4wifi"
Then I tried to install another recovery (a friend made it with this recovery) : andrewrecov.
This recovery starts scrolling, hard to read, then too fast to read anything.
I search for a solution on the web, but found nothing.
Just found some guys saying it's a rare problem, but I don't have any solution.
Any ideas ?
Thanks for your help
Just making a guide to fix, Keep an eye on the General forum!
Thanks mate
I tried a lot of things found on the Web but none fixed my problem.
I hope your solution will solve it.
Hi,
So i am not alone to get this problem
I dont have fixed the problem but find a workaround, if you install KANG (and other rom with scolling pb), if you lock screen (with power button) and wake up, scroll don't exist anymore and display is fine.
If you reboot the tab you have to redo lock/unlock.
After you do this the only display problem that subsist is when you change from portrait to landscape, screen goes black for a half of a second before rotating.
ddup1 said:
Hi,
So i am not alone to get this problem
I dont have fixed the problem but find a workaround, if you install KANG (and other rom with scolling pb), if you lock screen (with power button) and wake up, scroll don't exist anymore and display is fine.
If you reboot the tab you have to redo lock/unlock.
After you do this the only display problem that subsist is when you change from portrait to landscape, screen goes black for a half of a second before rotating.
Click to expand...
Click to collapse
I didn't try that, I will but it's not an acceptable solution
I really don't understand why some tablets have this problem and not all.
Maybe the Tablet origin ?
As I see you're french (me too), I bought it on rueducommerce. Same seller or another ?
Just flash another version of CWM that doesn't flicker, there are many versions of 5, doesn't matter which because in the end the ICS installs it's own CWM later.
Azertouf said:
I didn't try that, I will but it's not an acceptable solution
I really don't understand why some tablets have this problem and not all.
Maybe the Tablet origin ?
As I see you're french (me too), I bought it on rueducommerce. Same seller or another ?
Click to expand...
Click to collapse
Yeah not acceptable but no choice actually.
I bought my gtab at auchan.
There is another post about recovery flicker bug maybe its a way to get all work fine because the guy success to boot any recovery without flickering :
http://forum.xda-developers.com/showthread.php?t=1555984
Problem solved with this guide
Thanks
Azertouf said:
Problem solved with this guide
Thanks
Click to expand...
Click to collapse
What guide????
recovery rolling on p7510 with twrp 2.2.0 flashed
Noob - I've looked around a ton here trying to find some help with escaping recovery mode when the screen is rolling like this and just haven't had any luck at all...
So I flashed CWM 5.5.0.4 and went into recovery mode on my perfectly stock p7510 and got the rolling screen. I was able to see enough of the interface to reboot and was fine again - figured (stupidly now I'm seeing) that twrp 2.2.0 might not have this problem. So I flashed THAT recovery system and I'm still scrolling...however, because it's a touch screen interface now I'm pretty jammed.
What can I do about this? Is there a way to push through a reboot command?
UPDATE: WOW, I managed to peck my way back to Honeycomb. CRAZY. Going back to the "fix the scrolling screen" threads.....
Recovery Screen Scrolling
Hi, I just installed ICS on my GT-P7510 Galaxy Wifi Tablet but if I go into the ClockWorkMod recovery screen it scrolls incessantly (trying to re-root the tablet). This is the ICS Firmware/build P7510XABLPL_P7510UELPL_HOME.tar.md.5 that I installed. The device was rooted but not anymore after flashing from Honeycomb using Odin3_v1.85. I've tried installing recovery.tar.md5.....no luck......I tried installing ClockworkMod_Recovery_v5.5.0.4_P75xx.....no luck screen still scrolls. Can I even install anything via Odin now that the tablet is no longer rooted? Am I able to restore the tablet back to it's stock ROM? Am I able to do it through Kies? The tablet works on ICS as far as I can tell but I sure would like to root it again or have I in a sense "semi-bricked" it? I am a NOOB and would REALLY appreciate any feedback to get me out of this jam. I have read other posts about screens scrolling but nothing about it being the ClockWorkMod screen. Thanks to any and all who reply.
There are solutions for this. The easiest way that I have seen for ICS is to flash pershoot's bootloader variant and CWM recovery.
Go here: http://droidbasement.com/galaxy/roms/cm9/p4wifi/ and download the bootloader and recovery tar.md5 files. Flash them both via download mode with Odin and you should be fine. Come on back and let us know how you made out.
Sent from my GT-P7510 using XDA Premium HD app
djmatt604 said:
There are solutions for this. The easiest way that I have seen for ICS is to flash pershoot's bootloader variant and CWM recovery.
Go here: http://droidbasement.com/galaxy/roms/cm9/p4wifi/ and download the bootloader and recovery tar.md5 files. Flash them both via download mode with Odin and you should be fine. Come on back and let us know how you made out.
Sent from my GT-P7510 using XDA Premium HD app
Click to expand...
Click to collapse
I have same issue on P7500...
Does this solution work for P7500 also ?
His Nibs said:
Hi, I just installed ICS on my GT-P7510 Galaxy Wifi Tablet but if I go into the ClockWorkMod recovery screen it scrolls incessantly (trying to re-root the tablet). This is the ICS Firmware/build P7510XABLPL_P7510UELPL_HOME.tar.md.5 that I installed. The device was rooted but not anymore after flashing from Honeycomb using Odin3_v1.85. I've tried installing recovery.tar.md5.....no luck......I tried installing ClockworkMod_Recovery_v5.5.0.4_P75xx.....no luck screen still scrolls. Can I even install anything via Odin now that the tablet is no longer rooted? Am I able to restore the tablet back to it's stock ROM? Am I able to do it through Kies? The tablet works on ICS as far as I can tell but I sure would like to root it again or have I in a sense "semi-bricked" it? I am a NOOB and would REALLY appreciate any feedback to get me out of this jam. I have read other posts about screens scrolling but nothing about it being the ClockWorkMod screen. Thanks to any and all who reply.
Click to expand...
Click to collapse
Hi. I have the same issue as you, but with an P7500..
You can easely restore your device with ODIN and P7500XXLQ8_P7500OXALQ8_P7500XXLQ8_HOME.tar.md5 (ICS4.04).. So no problems there..
But the problem with screen flickering remains.. Plz let us know if this solution worked for you..
I do not know if I can use this solution, as it seems to be for P7510 only..
djmatt604 said:
There are solutions for this. The easiest way that I have seen for ICS is to flash pershoot's bootloader variant and CWM recovery.
Go here: http://droidbasement.com/galaxy/roms/cm9/p4wifi/ and download the bootloader and recovery tar.md5 files. Flash them both via download mode with Odin and you should be fine. Come on back and let us know how you made out.
Sent from my GT-P7510 using XDA Premium HD app
Click to expand...
Click to collapse
Which cwm version is that and is it good for stock?
It's the latest release from pershoot for CWM non-touch recovery. Last I checked it was 6.0.1.2 but that was just about a week ago.
I downloaded both tar.md5's and flashed them both - bootloader first, rebooted, rebooted into recovery, flashed new recovery, done. I was on stock LPL at the time. Hope it works out!
EDIT: I've been working on getting a crisp list of steps together for a new FIX post with bugs9477 and will post that at some point this week. It will be specifically for ICS because everyone here now knows how to fix the roll for HC.
djmatt604 said:
There are solutions for this. The easiest way that I have seen for ICS is to flash pershoot's bootloader variant and CWM recovery.
Go here: http://droidbasement.com/galaxy/roms/cm9/p4wifi/ and download the bootloader and recovery tar.md5 files. Flash them both via download mode with Odin and you should be fine. Come on back and let us know how you made out.
Sent from my GT-P7510 using XDA Premium HD app
Click to expand...
Click to collapse
Thanks djmatt604 but it did not resolve my issue. Hmmmm 604 that's my area code lol! Can anyone tell me if you can re-flash the stock Honeycomb ROM back onto the device using Odin and where can I find the stock ROM? I've searched on the forums and there are links but some of them are dead/no longer working or they are for Custom ROMs.
---------- Post added at 09:17 AM ---------- Previous post was at 09:13 AM ----------
djmatt604 said:
It's the latest release from pershoot for CWM non-touch recovery. Last I checked it was 6.0.1.2 but that was just about a week ago.
I downloaded both tar.md5's and flashed them both - bootloader first, rebooted, rebooted into recovery, flashed new recovery, done. I was on stock LPL at the time. Hope it works out!
EDIT: I've been working on getting a crisp list of steps together for a new FIX post with bugs9477 and will post that at some point this week. It will be specifically for ICS because everyone here now knows how to fix the roll for HC.
Click to expand...
Click to collapse
Thanks djmatt604 but it did not resolve my issue. Hmmmm 604 that's my area code lol! Can anyone tell me if you can re-flash the stock Honeycomb ROM back onto the device using Odin and where can I find the stock ROM? I've searched on the forums and there are links but some of them are dead/no longer working or they are for Custom ROMs. your link has given me these: US_LPL_4.0.4_bootloader.zip & recovery.tar.md5. I do not see 6.0.1.2. I think part of my problem is when I flashed ICS onto my tablet in the instructions I was reading there was nothing about wiping the old ROM off the sd card FIRST then flashing the new ROM onto the formatted sd card.
---------- Post added at 09:52 AM ---------- Previous post was at 09:17 AM ----------
Before you give up, try flashing the attached file "ClockworkMod_Recovery_v5.5.0.4_P75xx.tar" via Odin. BUT instead of putting it in the PDA section, load it in the BOOTLOADER section, then flash. This solution WORKED!!!!!!!!!! A BIG ROUND OF APPLAUSE to brGabriel!!!:good:
---------- Post added at 09:56 AM ---------- Previous post was at 09:52 AM ----------
xenofexos said:
Hi. I have the same issue as you, but with an P7500..
You can easely restore your device with ODIN and P7500XXLQ8_P7500OXALQ8_P7500XXLQ8_HOME.tar.md5 (ICS4.04).. So no problems there..
But the problem with screen flickering remains.. Plz let us know if this solution worked for you..
I do not know if I can use this solution, as it seems to be for P7510 only..
Click to expand...
Click to collapse
Try this solution it solved my issue but be sure to thank brGabriel for this ingenious solution! http://forum.xda-developers.com/showthread.php?p=31153208
Glad you got it worked out! FYI the recovery.tar.md5 is the CWM 6.0.1.2. If you flashed it and rebooted into recovery you'd see the version # at the top of the recovery screen.
Further, if you're flashing stock firmware via Odin (not a flashable ROM file, the stock firmware tar.md5) it will automatically wipe and relay the partitions for the entire tablet - /data,/cache,/system (the ROM itself), /sdcard (all of your storage), bootloader, all of it. You start completely clean when you go that route.
---------- Post added at 09:52 AM ---------- Previous post was at 09:17 AM ----------
[/COLOR]Before you give up, try flashing the attached file "ClockworkMod_Recovery_v5.5.0.4_P75xx.tar" via Odin. BUT instead of putting it in the PDA section, load it in the BOOTLOADER section, then flash. This solution WORKED!!!!!!!!!! A BIG ROUND OF APPLAUSE to brGabriel!!!:good:
---------- Post added at 09:56 AM ---------- Previous post was at 09:52 AM ----------
Try this solution it solved my issue but be sure to thank brGabriel for this ingenious solution! http://forum.xda-developers.com/showthread.php?p=31153208
Click to expand...
Click to collapse
I appreciate the acknowledgement but I can't take full credit. I came across it somewhere while searching for a solution myself. It worked for me on stock-based ICS so I thanked the original poster. It should be noted that with that particular recovery, you may not be able to flash a CM9 or CM10 ROM until you've flashed the latest CWM recovery which you can get from www.droidbasement.com
Good luck guys
djmatt604 said:
Glad you got it worked out! FYI the recovery.tar.md5 is the CWM 6.0.1.2. If you flashed it and rebooted into recovery you'd see the version # at the top of the recovery screen.
Further, if you're flashing stock firmware via Odin (not a flashable ROM file, the stock firmware tar.md5) it will automatically wipe and relay the partitions for the entire tablet - /data,/cache,/system (the ROM itself), /sdcard (all of your storage), bootloader, all of it. You start completely clean when you go that route.
Click to expand...
Click to collapse
So how do you know if it's stock firmware vs. a flashable ROM file? I downloaded this: GT-P7510_XAB_P7510UEKMP_P7510XABKMP_P7510UEKMP onto my PC in hopes that it is the original HC firmware I had on my GT-P7510 and was going to flash it back onto my GT-P7510 if the scrolling CWM screen issue couldn't be resolved. How are you able to differentiate on whether you should use ClockWorkMod (via recovery mode) to download ROM onto SDcard then install ROM off SDcard or use Odin to install ROMS?
Thanks once again for your assistance!
Galaxy S5 Sport SM-G860P Stock Roms
OH1 stock Lollipop Kernel added to the bottom of this post!
Kitkat 4.4.2 NG3 Stock Deodexed ROM
This is a base test version.
Someone please backup, flash with custom recovery and let me know how it goes in case I need to make some further changes.
Download Link -- > SM-G860P_NG3_ROOTED_DEODEXED.TEST.zip
Deodexed Rom Features (so far):
- root included
- busybox
- init.d support/repacked kernel
Full Stock Tar Recovery
Restore the phone back to stock.
Download Link -- > G860PVPU1ANG3_G860PSPT1ANG3_SPR.zip
Custom Recovery:
Flash custom roms and mods.
[RECOVERY] CWM S5 Sport SM-G860P
Instructions to Install Tar Files with Odin
• The full tar does not wipe Data or internal SD.
You may want to do a full wipe in custom recovery before flashing full tar if you have issues with data apps.
• Extract (unzip) the firmware file
• Extract Odin -- Odin v3.09 Download Link
• Power down the phone (or pull the battery, it is important to flash the OTA from a powered off state)
• Open Odin v3.09
• Boot the phone in Download Mode (press and hold Home + Power + Volume Down buttons)
• Connect phone and wait until you get a blue sign in Odin
• Add the firmware/recovery file to AP / PDA (depending on version of Odin)
• For modems, add the file to CP / PHONE (depending on version of Odin)
• Make sure re-partition is NOT ticked
• Click the start button, sit back and wait a few minutes
I think its possible to flash a Sprint SM-G900P 4.4.2 rom on this phone if you follow the following steps:
1. Have custom recovery already installed and a backup in place in case you need to flash back.
2. Place the rom and stock kernel on phone SD
3. Boot into custom recovery, do a full wipe
4. Install the SM-G900P touchwiz based rom, do not reboot yet
5. Flash the stock SM-G860P _NG3_Stock_Kernel.zip provided in Post #1.
6. Restart the phone
@SeanRinVA and @wolfleatherworks :
You guys have showed interest in getting MOAR on your SM-G860P phones, so I thought I'd mention you here to help you find this thread. Make sure to have a nanoid backup beforehand and let everyone know how it went.
I'd watched the MOAR thread for a while, but it wasn't compatible with the SM-G860P (hung boot).
Sent from my SM-G860P using Tapatalk
SeanRinVA said:
I'd watched the MOAR thread for a while, but it wasn't compatible with the SM-G860P (hung boot).
Sent from my SM-G860P using Tapatalk
Click to expand...
Click to collapse
@tdunham just posted this yesterday and the second post this morning, but yes, he's looking for someone to test it (neither of us have the G860). If you have the time, could you give this a try and post back success or failure? Especially if you can get MOAR installed.
Ramer said:
@tdunham just posted this yesterday and the second post this morning, but yes, he's looking for someone to test it (neither of us have the G860). If you have the time, could you give this a try and post back success or failure? Especially if you can get MOAR installed.
Click to expand...
Click to collapse
I can test it tonight. I've downloaded the Kernel...now to download the latest MOAR.
I've got an S5 Sport, just picked up today. Will be testing the kernel with MOAR.
---------- Post added at 08:32 PM ---------- Previous post was at 07:58 PM ----------
Well it doesn't seem to be boot looping, I'll let it sit and cook for a bit longer. Currently it's just flashing the android white text and disappearing, not sure how long it should normally be on 1st boot.
---------- Post added at 08:46 PM ---------- Previous post was at 08:32 PM ----------
Doesn't seem to have worked, I waited a good while but it didn't go any further. Attempted downloading your Rooted Deodexed test but it downloads as a 0kb file.
EDIT: Tried another mirror, seems to be downloading properly now.
---------- Post added at 09:34 PM ---------- Previous post was at 08:46 PM ----------
Got it downloaded, copied over via adb -- attempted install, getting (bad) - installation aborted.
---------- Post added at 09:42 PM ---------- Previous post was at 09:34 PM ----------
Confirmed MD5 match. Ideas?
KrimsonStarfly said:
Doesn't seem to have worked, I waited a good while but it didn't go any further. Attempted downloading your Rooted Deodexed test but it downloads as a 0kb file.
EDIT: Tried another mirror, seems to be downloading properly now
Got it downloaded, copied over via adb -- attempted install, getting (bad) - installation aborted.
Click to expand...
Click to collapse
I'm not sure what adb was for. You don't have drivers installed with a running rom so you can copy everything over to the phone?
Did you download the stock rom last night because the stock rom last night had a problem and has since been replaced. The one you should have the same name as the link in the OP. I even flashed it to make sure it would at least run.
tdunham said:
I'm not sure what adb was for. You don't have drivers installed with a running rom so you can copy everything over to the phone?
Did you download the stock rom last night because the stock rom last night had a problem and has since been replaced. The one you should have the same name as the link in the OP. I even flashed it to make sure it would at least run.
Click to expand...
Click to collapse
I was using ADB since I didn't want to restore from backup until I was done testing. I'll try re-downloading and doing it over again to see if I can get it working, I'm off work today so now is the perfect time to try it further.
So this has me stumped -- For some unknown reason, I seem to be unable to copy over SM-G860P_NG3_ROOTED_DEODEXED.TEST.zip using MTP. I fiddled with drivers for the last hour and i'm at a loss -- it doesn't seem to be a driver problem, I can copy over MOAR and other files, but it won't let me copy over your test at all.
tdunham said:
I think its possible to flash a Sprint SM-G900P 4.4.2 rom on this phone if you follow the following steps:
1. Have custom recovery already installed and a backup in place in case you need to flash back.
2. Place the rom and stock kernel on phone SD
3. Boot into custom recovery, do a full wipe
4. Install the SM-G900P touchwiz based rom, do not reboot yet
5. Flash the stock SM-G860P _NG3_Stock_Kernel.zip provided in Post #1.
6. Restart the phone
Click to expand...
Click to collapse
Ramer said:
@tdunham just posted this yesterday and the second post this morning, but yes, he's looking for someone to test it (neither of us have the G860). If you have the time, could you give this a try and post back success or failure? Especially if you can get MOAR installed.
Click to expand...
Click to collapse
works booted up with moar rom :good:
---------- Post added at 09:39 PM ---------- Previous post was at 09:33 PM ----------
tdunham said:
Galaxy S5 Sport SM-G860P Stock Roms
Kitkat 4.4.2 NG3 Stock Deodexed ROM
This is a base test version.
Someone please backup, flash with custom recovery and let me know how it goes in case I need to make some further changes.
Download Link -- > SM-G860P_NG3_ROOTED_DEODEXED.TEST.zip
Deodexed Rom Features (so far):
- root included
- busybox
- init.d support/repacked kernel
Full Stock Tar Recovery
Restore the phone back to stock.
Download Link -- > G860PVPU1ANG3_G860PSPT1ANG3_SPR.zip
Custom Recovery:
Flash custom roms and mods.
[RECOVERY] CWM S5 Sport SM-G860P
Instructions to Install Tar Files with Odin
• The full tar does not wipe Data or internal SD.
You may want to do a full wipe in custom recovery before flashing full tar if you have issues with data apps.
• Extract (unzip) the firmware file
• Extract Odin -- Odin v3.09 Download Link
• Power down the phone (or pull the battery, it is important to flash the OTA from a powered off state)
• Open Odin v3.09
• Boot the phone in Download Mode (press and hold Home + Power + Volume Down buttons)
• Connect phone and wait until you get a blue sign in Odin
• Add the firmware/recovery file to AP / PDA (depending on version of Odin)
• For modems, add the file to CP / PHONE (depending on version of Odin)
• Make sure re-partition is NOT ticked
• Click the start button, sit back and wait a few minutes
Click to expand...
Click to collapse
i tried SM-G860P_NG3_ROOTED_DEODEXED.TEST.zip but it aborted and said bad could be the . between DEODEXED and TEXT i try to rename but then it wouldnt let me put it on my phone. just a though
1991mustang50 said:
works booted up with moar rom :good:
---------- Post added at 09:39 PM ---------- Previous post was at 09:33 PM ----------
i tried SM-G860P_NG3_ROOTED_DEODEXED.TEST.zip but it aborted and said bad could be the . between DEODEXED and TEXT i try to rename but then it wouldnt let me put it on my phone. just a though
Click to expand...
Click to collapse
I accidentally added a space in the filename. I did flash it to test but now I think I removed the space in the name before doing so. If possible, try downloading to pc first and let me know how it goes in case I need to reupload it to the hosting site with a corrected filename.
1991mustang50 said:
works booted up with moar rom :good:
Click to expand...
Click to collapse
So, I'm not attempting to be dumb here, but it might be inevitable.
G900 stock roms boot with G860 kernel?
I use MOAR ROM(havent tried any other roms yet) for 900P and the the kernel zip in post #1 and using steps in post #2 I am running on it now
Great. Being a stock-based ROM, I would imagine that all stock Roms work with G860 kernel. Consequently, all AOSP ROMs should work with a kernel compiled for G860. There are 2 new G860s in the house and my intent was to compile CM11/12 for the Sport; however, if all that is necessary is the kernel&modules I won't bother pulling blobs.
Thanks. The phones aren't entirely at my disposal or I would do more testing.
tdunham said:
I accidentally added a space in the filename. I did flash it to test but now I think I removed the space in the name before doing so. If possible, try downloading to pc first and let me know how it goes in case I need to reupload it to the hosting site with a corrected filename.
Click to expand...
Click to collapse
Redownloaded still a no go it just go to opening update and then fails sorry for bad news thanks for trying
It works!
I used the instructions here to install the rom for the G900P as linked to below. I've messed with it only for about 20 minutes but it worked perfectly fine! So much bloatware though, and I'm coming from the S3 scene and am not too familiar with what the G900P had to offer in terms of custom ROMs. If anyone knows a good lightweight one with powerful customization options please let me know so I can try it. I am doing my first backup of this ROM as I type this and will also be doing a restore of my previous ROM (stock with the bloatware removed manually) for now and will probably tweak the MOAR ROM more later this week. Just want to say thank you to everyone in this thread, you guys are amazing!
http://forum.xda-developers.com/showthread.php?t=2790808
I'm going to give the MOAR of try with the kernel from post one.. I really do hope that more development comes to this phone..
doubledragon5 said:
I'm going to give the MOAR of try with the kernel from post one.. I really do hope that more development comes to this phone..
Click to expand...
Click to collapse
Well, at least you guys can run a custom rom now.
I wish I could be more help but I have the SM-G900P but thought I'd take a shot at getting the Sport a little help.
tdunham said:
Well, at least you guys can run a custom rom now.
I wish I could be more help but I have the SM-G900P but thought I'd take a shot at getting the Sport a little help.
Click to expand...
Click to collapse
I saw a couple of links in the recovery thread for the sport full resotore.. One link the files are over a gig, the other one is for about 848mb.. I wounder which is the real deal... The first link I could not download crap, but the second one I did. BTW is the modem included in your file for your rom?I was woundering because if I flash MOAR were can I find the modem or does it matter
i found this trwp recovery floating around i dont know who made it.
it boots fine but no touch screen hopefully someone can fix it
https://www.androidfilehost.com/?fid=457095661767138152
kvip60 said:
i found this trwp recovery floating around i dont know who made it.
it boots fine but no touch screen hopefully someone can fix it
https://www.androidfilehost.com/?fid=457095661767138152
Click to expand...
Click to collapse
What's the easiest way to install this?
I didn't install it I just used" fastboot boot image-name"
kvip60 said:
I didn't install it I just used" fastboot boot image-name"
Click to expand...
Click to collapse
Ok Thanks. I am in and generating a backup. The touch screen was working for me mostly. It won't let me select Micro SDCard to save my backup.
Yeah like I said it need some repair I am pretty sure the mount points aren't perfect and I didn't compile it I had to use an otg and mouse to navigate
kvip60 said:
Yeah like I said it need some repair I am pretty sure the mount points aren't perfect and I didn't compile it I had to use an otg and mouse to navigate
Click to expand...
Click to collapse
What I did to navigate was I had to push the power button then it would bring the screen up where you can swipe the bottom to unlock the screen and use touchscreen. Navigating the storage was odd because it shows it is stuck on Internal storage, but If i click on SDCard, it will take me to that directory. I hope there is a nice update to this is the near future, so we don't have to access it through "adb reboot recovery"
You can flash it if you like I just don't trust this copy yet waiting for an update before I flash it
You can use" fastboot flash recovery twrp.img" to flash rather than "fastboot boot twrp.img " to boot it
kvip60 said:
You can flash it if you like I just don't trust this copy yet waiting for an update before I flash it
You can use" fastboot flash recovery twrp.img" to flash rather than "fastboot boot twrp.img " to boot it
Click to expand...
Click to collapse
Oh man you were so right. I had it flashed and it caused me all kinds of problems, like booting the screen upside down etc. I was finally able to find the recovery.img in another thread and get back the stock recovery. I think I will also wait until there is a more stable TWRP version.
I always use boot to test and I always backup my recovery before flashing because I had that happen to me before
Any idea on when a decent working custom recovery will be available?
blahforme said:
Any idea on when a decent working custom recovery will be available?
Click to expand...
Click to collapse
Probably when someone will have the will & time to work on it.
Maybe you'd like to take on this topic?
Lol. I hear you. I have very little understanding of Linux I have tried to make one but there aren't enough information about compiling device /vendor tree for a new device to go on
Just visit this page and you will get TWRP for Z016D. It's a Taiwan website with Chinese but you can see the blue link marked as "TWRP" and there you are.
https://www.asus.com/zentalk/tw/thread-214217-1-1.html
lssong99 said:
Just visit this page and you will get TWRP for Z016D. It's a Taiwan website with Chinese but you can see the blue link marked as "TWRP" and there you are.
https://www.asus.com/zentalk/tw/thread-214217-1-1.html
Click to expand...
Click to collapse
Thanks for this. Posting the Mega so people don't have to make an Asus account to grab it.
https://mega.nz/#F!EkFF1CJD!C8o2wXMARW3YJFOipDttbA
The 20170218 recovery works perfectly with my phone (6/64gb, 820). The first one posted in the OP worked, but was a bit glitchy. The updated one has working SD reading and touchscreen works without having to lock it first.
Could someone please tell me why twrp is booting upside down on my device, and how do I fix it? I just tried to run it in fastboot boot twrp-3.0.3-0-Z016D-20170218.img and once again it loads upside down, however the touch screen is where it normally is suppose to be, which makes it very difficult to navigate the menus. It is very frustrating. This has happened to me multiple times this week. I can't seem to get it to boot/load properly.
blahforme said:
Could someone please tell me why twrp is booting upside down on my device, and how do I fix it? I just tried to run it in fastboot boot twrp-3.0.3-0-Z016D-20170218.img and once again it loads upside down, however the touch screen is where it normally is suppose to be, which makes it very difficult to navigate the menus. It is very frustrating. This has happened to me multiple times this week. I can't seem to get it to boot/load properly.
Click to expand...
Click to collapse
Are you using the Snapdragon 821 version by any chance? Cause people with the s820 seem to be working fine.
I am using 821 my screen is flipped and no touch even after locking it
Huffy1 said:
Are you using the Snapdragon 821 version by any chance? Cause people with the s820 seem to be working fine.
Click to expand...
Click to collapse
No, I am using the sd820.
---------- Post added at 08:25 PM ---------- Previous post was at 08:07 PM ----------
I really don't want to wipe everything and start all over from scratch because everything else is working great right now. I guess if there is no easy solution, then I will just leave it alone. I ran it with fastboot and then made a backup and saved it on my microSD card. But I am worried if I wipe everything and start all over again, then I will have to call my bank again to verify my cards for Android pay. I am running the stock firmware version 1698, with stock recovery, an unlocked bootloader, & rooted. Also have Magisk & Titanium Pro installed, and I verified that Andoid pay works for me. (I already bought something using Android pay).
blahforme said:
No, I am using the sd820.
---------- Post added at 08:25 PM ---------- Previous post was at 08:07 PM ----------
I really don't want to wipe everything and start all over from scratch because everything else is working great right now. I guess if there is no easy solution, then I will just leave it alone. I ran it with fastboot and then made a backup and saved it on my microSD card. But I am worried if I wipe everything and start all over again, then I will have to call my bank again to verify my cards for Android pay. I am running the stock firmware version 1698, with stock recovery, an unlocked bootloader, & rooted. Also have Magisk & Titanium Pro installed, and I verified that Andoid pay works for me. (I already bought something using Android pay).
Click to expand...
Click to collapse
How did you install Magisk having stock recovery? Using the in-app installation?
---------- Post added at 01:08 PM ---------- Previous post was at 01:05 PM ----------
It seems @EypCnn is the developer of this TWRP builds...
sebastiandg7 said:
How did you install Magisk having stock recovery? Using the in-app installation?
Click to expand...
Click to collapse
I flashed Magisk v11.1 with TWRP, then installed Magisk Manager from the Google Play Store, after I rebooted my device. I did that by booting in to TWRP with fastboot to flash the .zip file. I did not flash TWRP to install Magisk.
Hi guys,
So, I have this problem, after unbrick the phone it turn on whith the split screen. I use this method to unbrick: https://www.gizmochina.com/2016/11/20/leeco-x820-max-2-super-unbrick-guide/ and now the phon it´s like in the photo. I tried all the ways: installing a new twrp, only works the Cuoco92´s twrps but instead i can not flash any rom, it turn on in black screen. Also i tried to d flash with the adb sideload , whitout results. In twrp the screen is also splited.
Many people have this issue after unbrick, no solution.
LEvvvEL said:
Many people have this issue after unbrick, no solution.
Click to expand...
Click to collapse
It seems to be an issue with stock recovery and bootloader, their are not compatible. Why I´m telling you that? Because the digitalizator it is functional, the screenshots are entire and they are many people who can restore complet the phone, but they are offline , like STEVE_MARS and many other.
It could be the QFIL file you used , please try this one and tell us --> here
---------- Post added at 07:31 PM ---------- Previous post was at 07:21 PM ----------
here is the same problem , this guy has fix it --> here
AhmadSant said:
It could be the QFIL file you used , please try this one and tell us --> here
---------- Post added at 07:31 PM ---------- Previous post was at 07:21 PM ----------
here is the same problem , this guy has fix it --> here
Click to expand...
Click to collapse
I already did it bro , same result:split screen
burebista001 said:
I already did it bro , same result:split screen
Click to expand...
Click to collapse
have you look here ?
Are you sure you followed the OP carefully? There is a TWRP that is designated for using with the 014s ROM. Please use that one. I think the issue you have is with the drivers. Some users had installed another TWRP and they fixed it. Before 016s it was another kernel, therefore a different TWRP should be used. Also please mention when the screen became split, after finishing with QFIL, or after installing TWRP.
valy_cta said:
Are you sure you followed the OP carefully? There is a TWRP that is designated for using with the 014s ROM. Please use that one. I think the issue you have is with the drivers. Some users had installed another TWRP and they fixed it. Before 016s it was another kernel, therefore a different TWRP should be used. Also please mention when the screen became split, after finishing with QFIL, or after installing TWRP.
Click to expand...
Click to collapse
This is the twrp installed after flash lemax2qfil
burebista001 said:
This is the twrp installed after flash lemax2qfil
Click to expand...
Click to collapse
Try 3.0.2-0 and 3.0.2-1. Unfortunately the post that I was referring to had a TWRP for 014s that worked for me and many others, but now the download link is dead. In that case, I can suggest the above versions. They look pretty old, enough to work with 014s. Try them and report back. By the way, you can find them in the unbrick guide, I posted the links there.
This it is the new stade of may phone. I have a custo twrp, 3.0.2 Cuoco92 and when I try to instal a new rom this happens:
https://www.youtube.com/watch?time_continue=9&v=72kNH_YbkW0
40-45 seconds later, this happens, I let it almost 40 minutes and... nothing:
https://www.youtube.com/watch?v=L-KeuL8s5Hc
Really, I can´t find any solution, it´out af my understanding...
It was solved without replacing the screen!
Ok so, I did as shown in the topic : https://forum.xda-developers.com/le-...tboot-t3525831
download twrp (The one I know didn't had the touchscreen issue)
boot from twrp (wish I had know about it before!) and not from one installed
upload zip file to /sdcard ( here's the catch, while in TWRP in don't have access to adb, the phone doesn't connect to pc or I don't know even I mount it, could be me. So i just put the archive at the root of the phone before booting to twrp from adb)
install rom
reboot
And ... it's ****ING WORKING!*
Really big thanks to ThE_MarD for his help!
AhmadSant said:
It was solved without replacing the screen!
Ok so, I did as shown in the topic : https://forum.xda-developers.com/le-...tboot-t3525831
download twrp (The one I know didn't had the touchscreen issue)
boot from twrp (wish I had know about it before!) and not from one installed
upload zip file to /sdcard ( here's the catch, while in TWRP in don't have access to adb, the phone doesn't connect to pc or I don't know even I mount it, could be me. So i just put the archive at the root of the phone before booting to twrp from adb)
install rom
reboot
And ... it's ****ING WORKING!*
Really big thanks to ThE_MarD for his help!
Click to expand...
Click to collapse
Oh man, I wish what the twrp is, mean whithout problem. Do you know the name?Also, the link you posted, don´t work
I don't know which version of twrp, the link provide the same steps
https://forum.xda-developers.com/showpost.php?p=70252527&postcount=2
AhmadSant said:
I don't know which version of twrp, the link provide the same steps
https://forum.xda-developers.com/showpost.php?p=70252527&postcount=2
Click to expand...
Click to collapse
Did same steps bro, didn´t work . I only can install roms with 5.6 kernel, but still split screen. If is not a HW problem , I think is a kernel compatibility with display drivers and motherboard. I think the phone has a display named "trully" , manufactured after 5.6 kernel, so there is the problem. It.´s only my opinion.
burebista001 said:
Oh man, I wish what the twrp is, mean whithout problem. Do you know the name?Also, the link you posted, don´t work
Click to expand...
Click to collapse
Heyyo, which TWRP versions have you tried so far? Have you tried as well with stock EUI recovery?
Please check this post
https://forum.xda-developers.com/showpost.php?p=75400567&postcount=19
---------- Post added at 08:58 AM ---------- Previous post was at 08:57 AM ----------
AhmadSant said:
It was solved without replacing the screen!
Ok so, I did as shown in the topic : https://forum.xda-developers.com/le-...tboot-t3525831
download twrp (The one I know didn't had the touchscreen issue)
boot from twrp (wish I had know about it before!) and not from one installed
upload zip file to /sdcard ( here's the catch, while in TWRP in don't have access to adb, the phone doesn't connect to pc or I don't know even I mount it, could be me. So i just put the archive at the root of the phone before booting to twrp from adb)
install rom
reboot
And ... it's ****ING WORKING!*
Really big thanks to ThE_MarD for his help!
Click to expand...
Click to collapse
Heyyo, always super glad to help a fellow Android enthusiast
ThE_MarD said:
Heyyo, which TWRP versions have you tried so far? Have you tried as well with stock EUI recovery?
Please check this post
https://forum.xda-developers.com/showpost.php?p=75400567&postcount=19
---------- Post added at 08:58 AM ---------- Previous post was at 08:57 AM ----------
Heyyo, always super glad to help a fellow Android enthusiast
Click to expand...
Click to collapse
Hey bro, I did it already, and try with stock recovery, twrp 3.0.0 and twrp 3.0.2.0, only it let mi flash this 3 recovery.
Try these methods here