Note 2 problem: Bootloop, recovery doesn't work, Odin fails - Android Q&A, Help & Troubleshooting

Hey Guys,
So, few months ago I had a problem with my Note 2 being very slow and freezing very frequently after it used to work very well. I decided to make a soft reset followed by a hard reset but the problem was still there. I decided then to flash a stock firmware which I used before and worked well. This time while I was flashing the firmware, the USB cable was removed and from here the coming problems appeared. I am having now a constant loop of the Samsung logo and I can not enter the recovery mode. When I try to enter the recovery mode, it just goes to the logo loop. I tried to flash a stock recovery but it failed and I got the following message:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I tried to flash it using TWRP and I got the same message. Also, when I try to flash the stock firmware, I get a fail message at sboot.img. Managed to make it bypass sboot.img but it got another fail at boot.img. Now it is stuck at this:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
I tried two Odin versions (Odin 3 .12 and 3.04). I also tried different USB cables and ports. I am not sure if this may help as well to identify my problem but when I try to charge my battery, I get it stuck at this as shown in the image:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Related

[Q] Can't get SCH-I605 back to stock

I tried to flash my note 2 to 4.1.2 and it failed. Now I'm just trying to get it back to stock. It keeps failing on modem.bin.
I've tried...
I605_VRALJB_Restore.tar
CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW-Rev0406_low_ship_user.tar
CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar
root66_VZW_stock_system.tar
My OS is Windows 8 64 bit.
Odin message is as follows
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI605_I605VRLJB_I605VRALJB_CL414933_HWID04_HW_Rev0406_low_ship_user.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas?
If I remember right you should try a different version.
I tried using my work computer (also windows 8 64 bit) and finally got the root66_VZW_stock_system.tar file to flash, but then it gets stuck in a boot loop.
What version should I be trying?
Thanks
I can get the phone to boot using root66 (http://forum.xda-developers.com/showthread.php?t=2024207) or VRALJB_rootedstockdeo.zip (from beans - http://www.androidfilehost.com/?fid=9390225151984926781), but I get no signal. My IMEI is uknown. I've been able to generate a new IMEI file with sgs3.nv.gen, but nv-items_reader_writer won't push it to my phone (http://forum.xda-developers.com/showthread.php?t=1804123).
While playing around I noticed something odd with the phone in windows explorer (image below). My internal memory and external sdcard seem fine, but the internal sdcard seems hosed. I tried creating a folder and it threw up an error. I'm guessing my partitions are all borked, but I'm not sure how to get them back to normal. Once the phone is back to normal I'm sure I can get my IMEI back in there and everything working again.
I've tried Section 1a and Section 1b from the root66 link above with no luck. I've tried a few other pit files with no luck. They hang on Get mapping for PIT in odin.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

[Q][HELP][RECOGENIZE DEVICE] Samsung i9300

I am buy device i9300 (android 4.0.4.)
decided to update the firmware. Put CyanogenMod 10.3. Device to turn but lost contact. rolled on I9300XXEMG4_I9300OXEEMH1_I9300XXEMG4_HOME. The device is now nevkakuyu no firmware is not sewn Nand EROR Write ...
whats firmware i need for this device????
into recovery not loading. loading only dowload (sometimes in product model: empty, sometymes :i9300)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Looks like a genuine I9300 with SDS, new motherboard required.
You need a new motherboard Nand damaged .
boomboomer said:
Looks like a genuine I9300 with SDS, new motherboard required.
Click to expand...
Click to collapse
who can say for what country they are made? why radio 9308 another spares 9300???
Different countries have different radio frequencies, but the i9300 is the international version. Who knows why Samsung gave internal parts their own number?
1
i think 4.3 bootloader blocks any write?mayby i am need CHINA FIRMWARE ??? i am writed SER-SEK-RTL after device died....
mayby only emmc change? how much they coast?
http://www.youtube.com/watch?v=rOYo9AcUQQI
Koldunchik said:
i think 4.3 bootloader blocks any write?mayby i am need CHINA FIRMWARE ??? i am writed SER-SEK-RTL after device died....
mayby only emmc change? how much they coast?
http://www.youtube.com/watch?v=rOYo9AcUQQI
Click to expand...
Click to collapse
emmc is a new motherboard .
Fascinating video, needs a lot of practise and failed attempts I'd guess.
No idea where you'd buy one, ebay?
i think i am firmware 4.3 cyanogen 10.3 (update bootloader to 4.3), after this absent network, i am firmware (SER) I9300XXEMG4_I9300OXEEMH1_I9300XXEMG4_HOME
odin write PASS but device freez at the screen (flashing) after device not give to upload any Firmware, i think 4.3 bootloader (see my phone region and don give it firmware another)
who can give SD Card method to try emmc rewrite? i am have only GPG S-Boot cable.... they only boot in factory mode in dowload)
buy it at internet market, they are said that it from spain upgreded for SER SEK RTL
after write recovery-clockwork-6.0.4.3-i9300.tar.md5 on my SDS
Code:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Erase...
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
my phone lost boot, now they not load Odin mode, GPG S-Cable not loading Factory Mode... and PC not see them...
How many times do you need the answer .
YOU NEED A NEW MOTHERBOARD .

HELP! Galaxy S3 - Odin stuck at get pit for mapping

I have GT-i9300 ( Galaxy S3 international ) and i get it accidentally to bootloop.
I cannot access to recovery, only download. So i try flash TWRP with Odin, but it stuck get pit for mapping.
I try these odin versions:
-3.12 ( latest )
-3.07
-1.85
With KIES it looping on connect.
I few times re-installed drivers without any luck.
I dont know what to do.
Please help. :crying:
_______________________________________________________________________________________________________________________
Odin log:
<ID:0/010> Added!!
<ID:0/010> Odin engine v(ID:3.1203)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
This time i disconnect my phone from PC.
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Screenshot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ADBdeveloper said:
I have GT-i9300 ( Galaxy S3 international ) and i get it accidentally to bootloop.
I cannot access to recovery, only download. So i try flash TWRP with Odin, but it stuck get pit for mapping.
I try these odin versions:
-3.12 ( latest )
-3.07
-1.85
With KIES it looping on connect.
I few times re-installed drivers without any luck.
I dont know what to do.
Please help. :crying:
_______________________________________________________________________________________________________________________
Odin log:
<ID:0/010> Added!!
<ID:0/010> Odin engine v(ID:3.1203)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
This time i disconnect my phone from PC.
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Screenshot:
Click to expand...
Click to collapse
I am sorry for your S3 but did you go samsung forum ?
This forum will you not help you.
And post your problem at Samsung Galaxy s3 forum will help you.

Xcover 3 odin3 failed flash = brick

Hi!
So i downloaded firmware with SamFirm
Flashed with odin3 v3.13, see image.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Odin log:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1375 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> Loke_Primary.bin
<ID:0/005> Loke_Recovery.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now phone only vibrates, no display.
Problem i tried to solve was stuck in samsung logo and not booting to os.
Did i broke it compeletely?
Hi first I would try to flash with old version of odin , for example odin 3.12 or 3.10 not the latest one .
If you are able to boot your phone to download mode is okay , just try another firmware for your region also use latest one !!!
If that doesn't help you try with DBT firmware which is without brand providers : ) ...
Good Luck : )
Teddy Lo said:
Hi first I would try to flash with old version of odin , for example odin 3.12 or 3.10 not the latest one .
If you are able to boot your phone to download mode is okay , just try another firmware for your region also use latest one !!!
If that doesn't help you try with DBT firmware which is without brand providers : ) ...
Good Luck : )
Click to expand...
Click to collapse
I cannot access download mode anymore
Any tips?
SakkeMO said:
I cannot access download mode anymore
Any tips?
Click to expand...
Click to collapse
Try with USB JIG it's not expensive at all : ).
https://www.ebay.com/itm/Micro-USB-...ng-Galaxy-S4-S3-S2-S-Note-3-2-1-/111378442299

Need help on how to root my Samsung XCover 4 G390F

Hello, I've seen this post https://forum.xda-developers.com/android/general/samsung-xcover-4-sm-g390-twrp-magisk-t3927209 and I've tried like everything to root the phone. I don't understand a lot of this area so I'm just following everything I see on the article and even on youtube but nothing seems to work. The main problem, as far as I know, is that I've tried used odin 13, even odin 10 and it just doesn't flash on it. So I've searched like why is it always failing and some guy on youtube made a video about opening powershell and try to work from there but it doesn't work anyway. Is it possible to get some help? Or is it just impossible to root? Sorry again cause I'm kinda newbie on this but I've searched so many pages already that I'm probably going go give up soon.
PS: I tried to install twrp and magisk but the only model available is Xcover 3 and not XCover 4, tried also kingo root, odin and the powershell booting. Everything has an error. I already have USB Debugging and OEM activated, of course. Thanks in advance
@duckkz
Because your goal is to get a rooted Android, then take note that neither TWRP recovery nor Magisk framework must get installed ( flashed ) before. You can achieve this with running a couple of ADB / Fastboot command.
jwoegerbauer said:
@duckkz
Because your goal is to get a rooted Android, then take note that neither TWRP recovery nor Magisk framework must get installed ( flashed ) before. You can achieve this with running a couple of ADB / Fastboot command.
Click to expand...
Click to collapse
My goal is to root or to get downgrade to android 8. I couldn't get it on ADB neither fastboot. always error
To root Android as 1st thing of all things these requirements must be fulfilled
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Next step is to install the USB-driver matching your device
jwoegerbauer said:
To root Android as 1st thing of all things these requirements must be fulfilled
Next step is to install the USB-driver matching your device
Click to expand...
Click to collapse
I've done what you said. I've gone to the article and used odin v3.13.3 and boot it on the phone. It still gets an error.
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1303)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 2599 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> param.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help?
up.. no one has any idea?

Categories

Resources