Return to Un-modded Stock:
Bootloader unlocked and TWRP and Root included
The file is 4gb compressed to 2gb. Depending on your connection it will probably take 20 to 45 minutes to download.
Be Advised
Do your research before flashing anything, I am not responsible for any damage caused to your device, due to impatience and missed steps. However, rest assured this recovery is solid and will absolutely return your X720 or X727 to stock 5.8.21s (with the bootloader already unlocked, TWRP installed and rooted)
I was asked by several people if I would be willing to share a link to my Stock X727 recovery, I created this thread to provide the 5.8.21s recovery for anyone who is experiencing dire issues or is simply wanting to restore the last official x727 recovery, as a daily driver or as a means to troubleshoot their issues by returning to the fully stock rom, stock partitions and ready to start over.
Attached is my full stock TWRP Recovery for my Le Eco Pro 3, version: 5.8.21s (X727)
It is a clean TWRP backup recovery that I did not mod in any way other than unlocking the bootloader.
The link is to my Google Drive account. https://drive.google.com/open?id=19dtLHmE5bsx5mdtEXOns4Z5drpeY79Em
The file is compressed
Ensure that you perform a full wipe before applying this recovery, and that you know what you are doing before attempting to install.
Please note that any changes that you make to your device is done at your own risk.
Please use caution and make sure that you have TWRP recovery installed.
Be in the habit of booting back to recovery before booting to system....This is a good practice for ensuring TWRP stays installed
You must unpack the downloaded 7zip file, before it will be useable.
As long as you can boot into TWRP and have root access you will have the full permissions needed to install anything , and reverse any actions that do not workout as planned.
Personally, I make a backup of my existing installation prior to making any changes. I recommend that you do the same. If you buy an OTG adapter and a USB 3.0 drive it takes 5 minutes.
The steps provided on the following link can be used to install my recovery file. https://forum.xda-developers.com/le-pro3/how-to/guide-return-to-stock-lock-bootloader-t3539513
When clicking the link, Google will attempt to scan. Click download to see the file, and then choose download if wanted.
Flash the appropriate files below for which ever device you own. ( X727 - Not needed, I provided the files anyway just in case.)
Firmware - X720
https://mega.nz/#F!kDgFQJ6R!MDhxCFw5KjfB0CfxAWwr9w
Firmware - X727
https://drive.google.com/open?id=136-4UpUUsj3exNsTc3d5n2iQuYUxr00H
Modems
X720: https://mega.nz/#F!pZ4WGARZ
Key : !2oG3Z2LS_wP8BzcWUQjfHg
X727: https://mega.nz/#F!NJ5VHS7Z
Key : !p0iO7bDiZ4kXny03EiAlWw
Build Prop Fix Device ID Tool ( Credit to @Ascertion )
https://mega.nz/#F!oAZ3yC4b
Key: !MDwbHXNTRdrpgMvQ42yviw
EFS:
Warning : Use this only if you have unrepairable IMEI Issues! Otherwise its not needed, and you could forever lose your original IMEI info.
https://drive.google.com/open?id=10n2VjwBYHmrq_PllcWmTaGUtMIeYynZ7
[B ]Just for Fun[/B] - Boot Screens and Boot Animations -
https://mega.nz/#F!JB51zbwR
Key: !sG_wXTPqyKpugg5QIZFo9w
These splash-screens and animations came from various sources. If you created them contact me so i can give you credit.
The Red Splash came from the Couco modified EUI : version 5.9.028s VR4
Other Helpful Hints and Tips More to Come!
Unlock Bootloader and Flash Roms, Gapps and Magisk https://forum.xda-developers.com/showpost.php?p=75009966&postcount=692 ( If using original Stock
Viper Settings : https://forum.xda-developers.com/showpost.php?p=75449097
Installing Viper and Dolby: https://forum.xda-developers.com/showpost.php?p=76362493&postcount=19
Edit
October 8, 2018:
I uploaded the Leeco Full Stock Rom 5.8.26s to my MegaDrive.
If you are selling your phone and want it to have stock without TWRP and without root , just flash this Rom and your stock radio driver "firmware" for your device
Link for EUI 21S : https://mega.nz/#!FRhh1ArL
Key: V5ua3oj91kFtgvLYBhl1X6Oq3bsScyDFruN3UptkWN0
A late reply to my issue but I just got around to restoring my Pro3. This worked while the last backup did not! Thanks!
Soul0Reaper said:
A late reply to my issue but I just got around to restoring my Pro3. This worked while the last backup did not! Thanks!
Click to expand...
Click to collapse
Thats Awesome! I am glad that it helped you.
Great work just what I needed only one problem for me after I flash rom reboot system and then go back into TWRP there seems to be encryption on it and I can't install or backup or do much. Is there a password or way around this TWRP encryption?
dunas2331 said:
Great work just what I needed only one problem for me after I flash rom reboot system and then go back into TWRP there seems to be encryption on it and I can't install or backup or do much. Is there a password or way around this TWRP encryption?
Click to expand...
Click to collapse
Sorry, I didn't get a notification for your message. The encryption is your storage.
Follow the instructions here to resolve: https://www.google.com/amp/s/forum....return-to-stock-lock-bootloader-t3539513/amp/
The link has instructions for getting past and removing encryption.
tsongming said:
Sorry, I didn't get a notification for your message. The encryption is your storage.
Follow the instructions here to resolve: https://www.google.com/amp/s/forum....return-to-stock-lock-bootloader-t3539513/amp/
The link has instructions for getting past and removing encryption.
Click to expand...
Click to collapse
Can you elaborate on what to do here I keep getting encryption password too and can't do anything in twrp
Hi tsongming, you know if can work on a x720?
thanks
Toni Moon said:
Hi tsongming, you know if can work on a x720?
thanks
Click to expand...
Click to collapse
Yes x720 and x727 are practically identical phones.
Sent from my LEX720 using XDA Labs
Scruffdog1978 said:
Can you elaborate on what to do here I keep getting encryption password too and can't do anything in twrp
Click to expand...
Click to collapse
I don't have time at the moment to provide lengthy instructions. With respect, I am providing a working, clean unlocked recovery file and pointing the way to instructions already that exist all throughout the LeEco forums.
But here's a quick answer
First use TWRP to reset your phone with a clean wipe, like you would for any ROM. Set developer options to the standard settings.
Next, your storage is encrypted. So it needs to be formatted. Use TWRP format the storage only. Then reboot to recovery.
****Important****
Don't ever format the storage without ensuring that you have a TWRP recovery. Always check the boxes to check if TWRP is installed before swiping. If you don't have a recovery you have a soft brick.
For you information, TWRP recovery is installed on it's on it very own partition. Formatting the storage does not affect the TWRP partition. Nonetheless, if you see the check box option, make sure they are checked.
I would suggest that you install the all in one tool : https://www.google.com/amp/s/forum....pment/tool-tool-one-mauronofrio-t3580611/amp/
This tool helps a lot and makes this stuff easier if are new to flashing custom Roms.. The all in one tool will update the Google driver and ADB installation on your computer.
After you format your drive you will have to flash the recovery from the PC. The links provided show all of the steps, or you can use the all for one tool. When your storage is encrypted you have no choice but to format.
If you use the all in one tool , see their page for instructions.
Read the instructions, then read them again. when learning something new it's a good idea to take notes.
Do not deviate from those steps or you could brick your phone.
There have been many people that have messaged me by PM who successfully returned to stock using my recovery, so it will work as long as you are careful and follow the instructions verbatim and you will be fine. Plus, It's a great idea to create your own working recovery before you begin.
Reminder, you are restoring to stock under you own discretion, I am not responsible if you miss a key step, have a power outage, use faulty cables or brick your device.
One final suggestion, when you install the recovery make sure your phone is fully charged. Unplug all unneeded external peripherals from your desktop computer.
Temporarily, disable antivirus, insert USB cable into the back of your desktop PC. Those outlets provide more power.
Please look past any typos, I typed this on little keys.
One last suggestion
Read this
http://www.androidtipsz.com/top-5-things-to-do-before-installing-a-custom-rom-on-your-android-device
Sent from my LEX720 using XDA Labs
Will I keep twrp after restore? Thanks
---------- Post added at 03:29 PM ---------- Previous post was at 02:53 PM ----------
meh4life321 said:
Will I keep twrp after restore? Thanks
Click to expand...
Click to collapse
Also, could I just restore the system?
Could I just flash this in TWRP and keep twrp as my recovery?
meh4life321 said:
Will I keep twrp after restore? Thanks
---------- Post added at 03:29 PM ---------- Previous post was at 02:53 PM ----------
Also, could I just restore the system?
Click to expand...
Click to collapse
No it will not keep twrp. follow the instructions in the link I provided above, there was no reason to duplicate the instructions on my post.
The difference is that my backup will restore your phone to Eui 5.8.21s with bootloader unlocked. You will need to reflash Twrp and root the phone with Magisk if you want to keep Twrp recovery ( that is what I would do) You will not be able to get OTA updates. But that doesn't matter because there probably not be any more OTA updates for the x727
Thank you, sir! This is great work. I was able to restore back to stock.
On the strange side of thing, my TWRP was saved. Previously, I was running AICP, but having multiple sound issues with it.
Here are the steps I followed to restore:
1) Move the file to OTG flash drive
2) Restore through TWRP via Restore
For my 727, it just reboot on logo, and doesn't go past it.
rob_z11 said:
For my 727, it just reboot on logo, and doesn't go past it.
Click to expand...
Click to collapse
It takes a while.
For me, I had the quickest experience by flashing Magisk afterwards. The stock Rom , Rooted, and with Xposed is actually pretty sweet.
tsongming said:
It takes a while.
For me, I had the quickest experience by flashing Magisk afterwards. The stock Rom , Rooted, and with Xposed is actually pretty sweet.
Click to expand...
Click to collapse
Will try again. How long is while? ?
rob_z11 said:
Will try again. How long is while?
Click to expand...
Click to collapse
It should not take more than 10 minutes, and will usually startup in 5. I just now restored one of my X727's with this recovery, using the OTG method that the last person used and viola in worked so there's no doubt. I have always used ADB until now.
However, unlike the other poster, I did lose Twrp and had to reinstall it.
Always, Always Ensure Twrp is permanently installed
Make sure that you are on the latest version of Twrp : https://twrp.me/leeco/leecolepro3.html
Run Magisk, install Rom, Install Magisk again
Personally, I use the latest version of Magisk : https://forum.xda-developers.com/apps/magisk/beta-magisk-v13-0-0980cb6-t3618589
You want a fully clean install before you flash.
Instructions are redundant of XDA: if you want something other than what you have read already: Click on my account history to find detailed instructions, ( I type too much, too often) Under most thanked, you can quickly find detailed instructions for installing , Roms, Rooting, Installing Twrp, How to wipe to avoid any issues.
Finally, if for some reason it still doesn't work, the file may have been corrupted.
Worst Case scenario : there are other recoveries available on XDA. Beware of the edited versions, they do not work as well as an unadulterated recovery.
tsongming said:
It should not take more than 10 minutes, and will usually startup in 5. I just now restored one of my X727's with this recovery, using the OTG method that the last person used and viola in worked so there's no doubt. I have always used ADB until now.
However, unlike the other poster, I did lose Twrp and had to reinstall it.
Always, Always Ensure Twrp is permanently installed
Make sure that you are on the latest version of Twrp : https://twrp.me/leeco/leecolepro3.html
Run Magisk, install Rom, Install Magisk again
Personally, I use the latest version of Magisk : https://forum.xda-developers.com/apps/magisk/beta-magisk-v13-0-0980cb6-t3618589
You want a fully clean install before you flash.
Instructions are redundant of XDA: if you want something other than what you have read already: Click on my account history to find detailed instructions, ( I type too much, too often) Under most thanked, you can quickly find detailed instructions for installing , Roms, Rooting, Installing Twrp, How to wipe to avoid any issues.
Finally, if for some reason it still doesn't work, the file may have been corrupted.
Worst Case scenario : there are other recoveries available on XDA. Beware of the edited versions, they do not work as well as an unadulterated recovery.
Click to expand...
Click to collapse
It actually worked for second time without any issues. Just can't get the root, but will follow your instructions.
Hi just wondering does this rom pass safetynet out of the box?
what is the date of the security patch of this rom?
thanks
blanktape said:
Hi just wondering does this rom pass safetynet out of the box?
what is the date of the security patch of this rom?
thanks
Click to expand...
Click to collapse
This recovery is stock EUI 5.8.21s. The exception is that the bootloader is unlocked, and it has TWRP Recovery instead of EUI Recovery. I do not remember which version of Magisk I Installed. I would advise that you flash the newest version of Magisk and you will not have any safety net issues.
If you are wanting a complete return to stock, you should instead reflash the stock Full Rom, which will reinstall EUI recovery and lockdown the bootloader.
Related
Hello,
I've unlocked my bootloader and subsequently had installed TWRP (months ago).
Not long after, I decided to go back to stock for a while, and went back to CM a month ago.
However, I realized back then that I was loading into stock recovery even after taking the steps to install TWRP (http://forum.xda-developers.com/honor-5x/development/root-kiw-l24-usa-kiwi-t3305190)
During these steps, there were no errors (fastboot/adb logs show all things were done successfully).
However, some funky quirk (that I don't remember) got me loaded with TWRP once, which gave me the window to install CM (I remember it involving having to be connected to the PC).
Now I'm trying to install a new CM build, but I can't get it loading TWRP.
I've downloaded the TWRP Manager App, which tells me that I have TWRP 3.0.0.0, but when I reboot to recovery, I am given the stock EMUI recovery.
Does anyone know what is happening in this case? Has anyone experienced a similar issue?
Thank you!
undesputed said:
Hello,
I've unlocked my bootloader and subsequently had installed TWRP (months ago).
Not long after, I decided to go back to stock for a while, and went back to CM a month ago.
However, I realized back then that I was loading into stock recovery even after taking the steps to install TWRP (http://forum.xda-developers.com/honor-5x/development/root-kiw-l24-usa-kiwi-t3305190)
During these steps, there were no errors (fastboot/adb logs show all things were done successfully).
However, some funky quirk (that I don't remember) got me loaded with TWRP once, which gave me the window to install CM (I remember it involving having to be connected to the PC).
Now I'm trying to install a new CM build, but I can't get it loading TWRP.
I've downloaded the TWRP Manager App, which tells me that I have TWRP 3.0.0.0, but when I reboot to recovery, I am given the stock EMUI recovery.
Does anyone know what is happening in this case? Has anyone experienced a similar issue?
Thank you!
Click to expand...
Click to collapse
Reinstallt it try this TWRP http://www.mediafire.com/download/15g5i63gke9ddgp/kiwi_twrp_3-21_recovery.img its version 3.0.2.0 (Most recent)
The most recent is 5-14 (also based on v3.0.2.0 ).
TWRP 5.14
3-21 was built on March 21, and 5-14 on May 14.
mooms said:
The most recent is 5-14 (also based on v3.0.2.0 ).
TWRP 5.14
3-21 was built on March 21, and 5-14 on May 14.
Click to expand...
Click to collapse
Just for the record I'm using a even newer one than the 5-14 posted above
@yuweng posted a version of 3.0.2.0 that will make images of many partitions on the phone that even 5-14 ignores
you can download it here >> https://www.androidfilehost.com/?fid=24588212152305793
please note it was discovered early on that you cannot share the oeminfo partition on the phone, it's locked to your device and can / will brick a phone it's not from. just be careful what you restore with such a powerful version of TWRP.
@undesputed
I have seen this before where flashing TWRP does not seem to stick.
boot to the bootloader and see if frp is unlocked ... if not you need to
boot to your OS and remove your google account from the device
reboot to the bootloader and attempt the flash again. if it still fails to stick you can always just use
fastboot boot twrp.img and it will work just fine... just not installed
Arobase40 said:
Do you mean 3.0.2.0 is newer and supports more partitions than 5-14 ???
Click to expand...
Click to collapse
Their both 3.0.2.0 the one I just posted has more features
Sent from my SM-N920T using Tapatalk
clsA said:
Just for the record I'm using a even newer one than the 5-14 posted above
@yuweng posted a version of 3.0.2.0 that will make images of many partitions on the phone that even 5-14 ignores
you can download it here >> https://www.androidfilehost.com/?fid=24588212152305793
please note it was discovered early on that you cannot share the oeminfo partition on the phone, it's locked to your device and can / will brick a phone it's not from. just be careful what you restore with such a powerful version of TWRP.
@undesputed
I have seen this before where flashing TWRP does not seem to stick.
boot to the bootloader and see if frp is unlocked ... if not you need to
boot to your OS and remove your google account from the device
reboot to the bootloader and attempt the flash again. if it still fails to stick you can always just use
fastboot boot twrp.img and it will work just fine... just not installed
Click to expand...
Click to collapse
@clsA
frp is labeled as "UNLOCK" as oppsed to bootloader labeled as "UNLOCKED".
If it's just about removing my google account, will this be resolved the next time I do a factory reset?
Nevertheless, thank you so much for the command fastboot boot twrp.img, I realized that that was what I had used the last time.
I'm currently able to boot into TWRP this way. Awesome!
@clsA
Thanks for the link & infos.
Can you tell which features are added in this new TWRP ? name of the partitions ?
Thanks.
mooms said:
@clsA
Thanks for the link & infos.
Can you tell which features are added in this new TWRP ? name of the partitions ?
Thanks.
Click to expand...
Click to collapse
it would be much easier to just install it and test it for yourself
I did find a bug it would not backup to my OTG stick
clsA said:
it would be much easier to just install it and test it for yourself
I did find a bug it would not backup to my OTG stick
Click to expand...
Click to collapse
I don't use all the features, so i will maybe miss the changes.
Never used OTG to made a backup (I use ext_SD), I don't know if it works with other builds of TWRP.
mooms said:
I don't use all the features, so i will maybe miss the changes.
Never used OTG to made a backup (I use ext_SD), I don't know if it works with other builds of TWRP.
Click to expand...
Click to collapse
USB-OTG works flawlessly on the 5-14 version I was not able to use it with the newer one @yuweng posted in his guide
the screen shots show all the partitions it's able to work with
Arobase40 said:
I thought 3.0.2.0 was just an interim version between twrp_2-27 and twrp_5-14... ^^
Click to expand...
Click to collapse
your confusing TWRP versions with TWRP release dates
2-27 and 5-14 are release dates where as 3.0.2.0 is the version of TWRP not the date
the first version of TWRP for this device was actually 2.8.7.0 and was released on 2-16-2016
Same issue
Hey so I have the same exact issue umm did you ever resolve this problem becuSe I can't seem to crack it and it's a bit frustrating cuz by no means am I a pro but coming from using the OnePlus one the OnePlus 2 the OnePlus x and the Nexus 6 rooting them and restoring them after many failed attempts resulting in bricking my phone and even eventually unbrick them I do know a thing or two and I am stumped please help you are the only other person in this world other then my self that seems to be having this issue if you don't mind would you be so kind and email gmail me cuz I don't use or check this forum often thanks millerfamily805
clsA said:
Just for the record I'm using a even newer one than the 5-14 posted above
@yuweng posted a version of 3.0.2.0 that will make images of many partitions on the phone that even 5-14 ignores
you can download it here >> https://www.androidfilehost.com/?fid=24588212152305793
please note it was discovered early on that you cannot share the oeminfo partition on the phone, it's locked to your device and can / will brick a phone it's not from. just be careful what you restore with such a powerful version of TWRP.
@undesputed
I have seen this before where flashing TWRP does not seem to stick.
boot to the bootloader and see if frp is unlocked ... if not you need to
boot to your OS and remove your google account from the device
reboot to the bootloader and attempt the flash again. if it still fails to stick you can always just use
fastboot boot twrp.img and it will work just fine... just not installed
Click to expand...
Click to collapse
Can it be used with other honor devices?
Got my answer... Thanks...
Sent from my PLK-L01 using XDA Labs
It depend on the device
Hi to all. I'm new in Honor world and I've stopped my Android experience with KitKat so I'm a little bit confused ...
I've read several guides (on XDA too) that that three steps to obtain root are unlock bootloader, flash TWRP via ADB and then install Magisk or SuperSU via TWRP. But in the thread on TWRP is clearly written that to install Magisk decryption is needed and to have decryption we must flash a kernel with encryption disabled in fstab. But no guide says anything about this step. Can someone explain me how encryption/decryption work doing a standard installation of TWRP ? Is needed a flash of a modified kernel ? And where find it ?
And another question (if it's not too much ). Since I don't need to install custom rom (I want root only to use some apps like Titanium) how can I make a backup of stock rom, boot.img, efs partition and all that can be useful to restore phone to the starting point if, by chance, I need Huawei warranty ?
Thanks a lot
Hi, apparently there's a way to get root on an encrypted system. Follow the rebrand guide and then flash supersu in TWRP via ADB sideload. It worked for me and a few others, there is no comment from the developers as of right now.
So basically in short follow this guide until you are finished with the TWRP section:
https://forum.xda-developers.com/honor-9/how-to/one-guide-recovery-os-roms-t3661829
Then
- enter twrp
- adb sideload supersu
Afterwards follow the "rooting!" section with point 2
Thank for your answer... I'd like to try to install Magisk instead of SuperSU. In several places is written that this should be right. I'll try....
unvisigoth said:
Thank for your answer... I'd like to try to install Magisk instead of SuperSU. In several places is written that this should be right. I'll try....
Click to expand...
Click to collapse
The method is also working fine with Magisk. Let me know if you need help
zxz0O0 said:
The method is also working fine with Magisk. Let me know if you need help
Click to expand...
Click to collapse
Finally done with a couple of hours of panic. This is the story if can be useful to someone...
Unlock bootloader....done TWRP install... done. Copy magisk (apk and zip) on phone than install apk without opening it. Reboot to recovery wipe all, factory reset. Trying to boot.....BOOTLOOP But I don't have installed Magisk zip. Only apk without opening it.
Nothing to do. Bootloop and then erecovery. I try to restore the backups previously done with TWRP. I restore boot and system partition. All wipes ...no luck. I don't know what has happened. While downloading full firmware to try to reinstall it I try to install magisk.zip. Install via TWRP. All wipes and then magically (it's such a case ) phone boots. Powered off and on several times no problem. Root (verified with root checker) ok.
I habe b100 release but I don't think to update to b130. I wait for Oreo...
The only two things that I can say are these: first TWRP even after flashing magisk gave an error (unable to mount system). Two while installing magisk it seems that magisk itself has patched something.
If someone has an explanation is welcome...
unvisigoth said:
Finally done with a couple of hours of panic. This is the story if can be useful to someone...
Unlock bootloader....done TWRP install... done. Copy magisk (apk and zip) on phone than install apk without opening it. Reboot to recovery wipe all, factory reset. Trying to boot.....BOOTLOOP But I don't have installed Magisk zip. Only apk without opening it.
Nothing to do. Bootloop and then erecovery. I try to restore the backups previously done with TWRP. I restore boot and system partition. All wipes ...no luck. I don't know what has happened. While downloading full firmware to try to reinstall it I try to install magisk.zip. Install via TWRP. All wipes and then magically (it's such a case ) phone boots. Powered off and on several times no problem. Root (verified with root checker) ok.
I habe b100 release but I don't think to update to b130. I wait for Oreo...
The only two things that I can say are these: first TWRP even after flashing magisk gave an error (unable to mount system). Two while installing magisk it seems that magisk itself has patched something.
If someone has an explanation is welcome...
Click to expand...
Click to collapse
So do you have some step-by-step instructions for someone who wants to unlock and root the phone with magisk?
shiboby said:
So do you have some step-by-step instructions for someone who wants to unlock and root the phone with magisk?
Click to expand...
Click to collapse
Here what I have done:
Unlock bootloader
install adb drivers (find something that is right for your PC. For example minimal ADB found on XDA weren't suitable for me. Google adb drivers...). Open a command windows (shift+right click). If typing "adb devices" your phone is found that's ok
Enable usb debugging and oem unlock (or in other words disable FRP, factory reset protection)
Put the phone in fastboot mode ("adb reboot bootloader"). If all ok typing "fastboot devices" your phone is found
Type "fastboot oem unlock xxxxxxxx" (xxxxxxxx is the code provided by Huawey)
Bootloader unlocked
Flash TWRP
Download TWRP recovery for Honor 9 (link found on other thread on this forum)
Put the phone in fastboot mode
Type "fastboot flash recovery xxxxx.img" (where xxxx.img is the recovery downloaded)
Reboot phone directly in Recovery to avoid erecovery overwrite TWRP. Booting on TWRP let TWRP patch to avoid erecovery booting
Now here I've had some issues as said (read previous post). My tip is the following:
after rebooting in TWRP make all wipes then reboot again in TWRP
Install Magisk.zip (for me download here https://geekaxe.com/root-honor-9-twrp-bootloader-unlocking/)
Reboot recovery
All wipes
Reboot to system
If it's all OK you can install magisk.apk and you are rooted
I suggest after flashing TWRP to make backup of all partitions on external SD (for some reasons, maybe encryption, backup on internal storage gives error). Again I suggest to copy all files that you need (i.e. magisk files) on external sd before starting all.
Pay attention that if you update firmware after this procedure I think that you must repeat all. For me I remain on original firmware found on phone (B100). B130 seems to have some bugs, B120 doesn't seem improve much. Moreover all releases are 7.0 based. I wait for Oreo, hopefully in some custom rom!
To add to this, a bootloop or two might be normal. Let it sit for a few minutes before considering re-flashing everything.
Thanks for your guide!
Zuzler said:
To add to this, a bootloop or two might be normal. Let it sit for a few minutes before considering re-flashing everything.
Thanks for your guide!
Click to expand...
Click to collapse
You're right. But after 20 minutes of bootlops I've chosen another way....:laugh::laugh:
unvisigoth said:
You're right. But after 20 minutes of bootlops I've chosen another way....:laugh::laugh:
Click to expand...
Click to collapse
So is it fixed?
Sent from my Honor 8 Pro using XDA Labs
adriansticoid said:
So is it fixed?
Sent from my Honor 8 Pro using XDA Labs
Click to expand...
Click to collapse
Yes sure. As said previously installation of magisk.zip fixed the bootloop problem. I think (but I could be wrong) that installation of TWRP corrupted the boot partition and magisk fixed it. But it's only an hypothesis...
unvisigoth said:
Yes sure. As said previously installation of magisk.zip fixed the bootloop problem. I think (but I could be wrong) that installation of TWRP corrupted the boot partition and magisk fixed it. But it's only an hypothesis...
Click to expand...
Click to collapse
Observe and be careful man.
Sent from my Honor 8 Pro using XDA Labs
unvisigoth said:
Yes sure. As said previously installation of magisk.zip fixed the bootloop problem. I think (but I could be wrong) that installation of TWRP corrupted the boot partition and magisk fixed it. But it's only an hypothesis...
Click to expand...
Click to collapse
Which TWRP version did you use?
I had a similar problem after formatting all data with the OpenKirin TWRP 3.1.1 Perhaps its an issue with this TWRP release?
I was able to recover in similar circumstances by flashing a stock boot.img over fastboot. Based on this, it's looking like Magisk is really the way to go for rooting atm. Making sure to pull my twrp backup with adb this time though.
If I'm lucky enough to install magisk and not get a bootloop the safetynet always fails. Anyone got a valid method of actually getting magisk working fully?
MTP does not work in TWRP on the Pixel 3 and will not work until we have time to update the TWRP MTP implementation. You may still use adb to push and pull files.
Pixel devices have 2 "slots" for ROMs / firmware. TWRP will detect whichever slot is currently active and use that slot for backup AND restore. There are buttons on the reboot page and under backup -> options to change slots. Changing the active slot will cause TWRP to switch which slot that TWRP is backing up or restoring. You can make a backup of slot A, switch to B, then restore the backup which will restore the backup of A to slot B. Changing the slot in TWRP also tells the bootloader to boot that slot.
The zip install method installs TWRP to both slots.
Installation:
If you already have TWRP installed: Download the latest zip and install the zip using TWRP.
If you do not already have TWRP installed: Download both the img and the zip. Copy the zip to your device. You will need to have fastboot binaries and the correct drivers installed. Power off your device completely. Hold volume down and turn on the device. Your device should now be in the bootloader. Connect the device to your PC. Open a command window and run the following command from the proper location:
fastboot boot path/to/twrp.img
This will temporarily boot TWRP on your device. If you are using a lockscreen pin/pattern/password and do not get prompted to enter your passord, reboot to the bootloader and try again. Go to install and browse to the zip and install the zip. If you are currently rooted, you will need to reflash the stock boot image before installing TWRP. After installing the stock boot image, follow the instructions for installing TWRP. Once TWRP is installed, you will need to reflash root.
If you accidently flash TWRP to your device using fastboot instead of temporarily booting the image, you will need to download the latest factory image for your device and reflash the boot image.
3.2.3-0: Initial release for the Pixel 3 devices
Pixel 3:
https://twrp.me/google/googlepixel3.html
https://dl.twrp.me/blueline/
Pixel 3 XL:
https://twrp.me/google/googlepixel3xl.html
https://dl.twrp.me/crosshatch/
Reserved.
You are the man! Cant believe we have TWRP this early! Just in time for the next OTA!
Thank you for this! Great work, it feels like an early Christmas!
All set up with TWRP and rooted again,,even made a back up,,,awesome job to the dev!
Thanks you!
Is anyone having the touchscreen not work after a reboot?
Archangel said:
All set up with TWRP and rooted again,,even made a back up,,,awesome job to the dev!
Click to expand...
Click to collapse
I got twrp up and running on my Pixel 3, but when try to install magisk 17.3 via twrp it says it completes but just bootloops. And I have to restore again. How did you go about it?
code_311 said:
Is anyone having the touchscreen not work after a reboot?
Click to expand...
Click to collapse
On the Pixel 2 XL touch was broken unless you used a custom kernel. I guess it's the same on 3. If you boot TWRP using fastboot it should allow touchscreen.
You would think after buying the Pixel 1, 2 and 3 I would have this whole A/B slot thing down pat but I dont LOL. That did the same thing for me too. I just rebooted into recovery and flashed TWRP again and it has been fine since. I think sometimes it switches slots and that causes the bootloop. I messed around with changing slots and I think I am on slot A and all if fine for me.
Mrnicgeuy633 said:
I got twrp up and running on my Pixel 3, but when try to install magisk 17.3 via twrp it says it completes but just bootloops. And I have to restore again. How did you go about it?
Click to expand...
Click to collapse
---------- Post added at 02:53 PM ---------- Previous post was at 02:52 PM ----------
I had that happen I think once and I just rebooted back into TWRP and it was fine.
code_311 said:
Is anyone having the touchscreen not work after a reboot?
Click to expand...
Click to collapse
Hey guys - I'm a pixel noob and have a quick question about TWRP/Magisk.
I was rooted before TWRP came out so I flashed the stock boot images back to slots A and B. Then I followed steps 2-12 of the following article to install both Magisk and TWRP using temp TWRP. https://www.xda-developers.com/google-pixel-3-unlock-bootloader-root-magisk/
My question is... when I was temp booted into TWRP, and installed the Magisk zip file, it only said that it installed to slot A. But when I was rooted before TWRP released I remember I had to flash the patched boot image to both slots. So using the process I followed, do I have one slot rooted and the other not? If so, is that a problem? Phone seems to work perfectly and root is working.
Sorry if this is a dumb question. I've always been a HTC guy but I'm trying
ktdt00 said:
Hey guys - I'm a pixel noob and have a quick question about TWRP/Magisk.
I was rooted before TWRP came out so I flashed the stock boot images back to slots A and B. Then I followed steps 2-12 of the following article to install both Magisk and TWRP using temp TWRP. https://www.xda-developers.com/google-pixel-3-unlock-bootloader-root-magisk/
My question is... when I was temp booted into TWRP, and installed the Magisk zip file, it only said that it installed to slot A. But when I was rooted before TWRP released I remember I had to flash the patched boot image to both slots. So using the process I followed, do I have one slot rooted and the other not? If so, is that a problem? Phone seems to work perfectly and root is working.
Sorry if this is a dumb question. I've always been a HTC guy but I'm trying
Click to expand...
Click to collapse
No, only the current slot needs to be rooted.
Hello,
I apparently have one of these Pixel 3's that are not working with the current version of TWRP (twrp-3.2.3-0-blueline.img). Yes, I have a 3, not a 3XL. I have done these a hundred times before so I am fairly confident I am not doing anything wrong either. I get the file to load through ADB but on the reboot, it just hangs on the Google screen forever. I have left it for an hour. I have tried everything I can think of. Does anyone have any advice or is in the same situation? I just got my Pixel 3 in the mail on Friday so it's as fresh as they come. I was thinking of fully flashing the TWRP image, but I really don't think it's going to make any difference and I don't want the extra hassle of tracking down the official boot.img from the repo. I guess I will just have to wait until someone who really knows how to debug these comes across one like mine. Clearly, something has changed in what Google is sending out.
For reference:
Android security patch level: September 5,2018
Baseband version: g845-00023-180815-B-4956438
Kernel Version: 4.9.96-g340a9aaf92bc-ab4959234 #0 Thu Aug 16 23:24:20 UTC 2018
Build number: PD1A.180720.031
Much appreciated! $50 donation to anyone who can get me past this and rooted. I'm an old-time Verizon unlimited data planner and I need that tether check disabled.
Is root
To Pixel 3 owners that succesfully rooted, can you share the build.prop here? /system/build.prop
when i booted in to twrp it was encrypted! but i didnt have a PW.... so for everyone to whom that happens, boot up normally and disable your pin ! then you can see your storage in twrp!
i almost flipped this morning hahahaha
Carmenlove said:
Hello,
I apparently have one of these Pixel 3's that are not working with the current version of TWRP (twrp-3.2.3-0-blueline.img). Yes, I have a 3, not a 3XL. I have done these a hundred times before so I am fairly confident I am not doing anything wrong either. I get the file to load through ADB but on the reboot, it just hangs on the Google screen forever. I have left it for an hour. I have tried everything I can think of. Does anyone have any advice or is in the same situation? I just got my Pixel 3 in the mail on Friday so it's as fresh as they come. I was thinking of fully flashing the TWRP image, but I really don't think it's going to make any difference and I don't want the extra hassle of tracking down the official boot.img from the repo. I guess I will just have to wait until someone who really knows how to debug these comes across one like mine. Clearly, something has changed in what Google is sending out.
For reference:
Android security patch level: September 5,2018
Baseband version: g845-00023-180815-B-4956438
Kernel Version: 4.9.96-g340a9aaf92bc-ab4959234 #0 Thu Aug 16 23:24:20 UTC 2018
Build number: PD1A.180720.031
Much appreciated! $50 donation to anyone who can get me past this and rooted. I'm an old-time Verizon unlimited data planner and I need that tether check disabled.
Click to expand...
Click to collapse
Flash the stock boot image. Then try to fastboot boot "path to TWRP". If it still hangs, redownload TWRP and try again. Here's the stock boot for Pixel 3... https://drive.google.com/file/d/1EMkcRkH7n-1bGlVbbzcEJKKPJeE4l9mB/view?usp=drivesdk
jsauder2 said:
Flash the stock boot image. Then try to fastboot boot "path to TWRP". If it still hangs, redownload TWRP and try again. Here's the stock boot for Pixel 3... https://drive.google.com/file/d/1EMkcRkH7n-1bGlVbbzcEJKKPJeE4l9mB/view?usp=drivesdk
Click to expand...
Click to collapse
Thanks! I will give it a try this morning after some coffee. I learned a cool trick last night to get my hotspot to work un-rooted, so I am less desperate than I was last night.
Carm
freebordjunky said:
when i booted in to twrp it was encrypted! but i didnt have a PW.... so for everyone to whom that happens, boot up normally and disable your pin ! then you can see your storage in twrp!
i almost flipped this morning hahahaha
Click to expand...
Click to collapse
Just enter your PIN at the TWRP prompt and it will work.
Mrnicgeuy633 said:
I got twrp up and running on my Pixel 3, but when try to install magisk 17.3 via twrp it says it completes but just bootloops. And I have to restore again. How did you go about it?
Click to expand...
Click to collapse
I have a similar problem. After installing twrp, I can boot to the OS, but Magisk isn't installed and I don't have root. After going back to Twrp and flashing the magisk zip, i can't get past the bootloader screen with a error saying something about failed to load boot.img.
Re-fastboot flashing the patched boot img to both slots brings me back to a rooted state with all magisk modules loaded and applied, but no more twrp. I technically don't need twrp for anything except for nandroid backups, but I guess i could just backup using the adb backup commands and get similar results, right?
Either way, I'm open to suggestions for how to get twrp and magisk working at the same time.
Hey guys I wanna know about the Pie update I have mi Mi 8 Lite and as soon as i power up and conect to a wifi and update to 10.2.2.0 ODTMIXM was available so i updated and no problem i unlocked the bootloader (15 days wait time, sad) and flash twrp no root because is magisk and i can't hide root (even with magisk default hide root) for a bank app so is not rooted but since five days I was notified about and update to Pie miui 10.2.2.0PDTMIXM stable (persistent notification) but here are some questions:
* the twrp will cause a problem if I download this update and the updater applies or I have to remove twrp (I'll make a twrp backup just in case I don't have the original img file)
* I've read there no version of twrp for Pie and the version for 8.1 is not ideal. (correct me if i'm wrong)
* I might not need root, no problem the miui have some tweaks and I'm getting used to miui. (I had a Moto X Play with root and xposed and some modules)
* Is the first stable version, should I wait for a next Pie version with bugs solved.?
* I'm knew to miui less than a month with my Mi 8 Lite
orozcore said:
Hey guys I wanna know about the Pie update I have mi Mi 8 Lite and as soon as i power up and conect to a wifi and update to 10.2.2.0 ODTMIXM was available so i updated and no problem i unlocked the bootloader (15 days wait time, sad) and flash twrp no root because is magisk and i can't hide root (even with magisk default hide root) for a bank app so is not rooted but since five days I was notified about and update to Pie miui 10.2.2.0PDTMIXM stable (persistent notification) but here are some questions:
* the twrp will cause a problem if I download this update and the updater applies or I have to remove twrp (I'll make a twrp backup just in case I don't have the original img file)
* I've read there no version of twrp for Pie and the version for 8.1 is not ideal. (correct me if i'm wrong)
* I might not need root, no problem the miui have some tweaks and I'm getting used to miui. (I had a Moto X Play with root and xposed and some modules)
* Is the first stable version, should I wait for a next Pie version with bugs solved.?
* I'm knew to miui less than a month with my Mi 8 Lite
Click to expand...
Click to collapse
There's a TWRP for pie
mr_reaper said:
There's a TWRP for pie
Click to expand...
Click to collapse
So your suggest is that I download the Pie update and let updater installs it and reflash twrp (is it the same version?)
orozcore said:
So your suggest is that I download the Pie update and let updater installs it and reflash twrp (is it the same version?)
Click to expand...
Click to collapse
Which TWRP version u running?
mr_reaper said:
Which TWRP version u running?
Click to expand...
Click to collapse
sorry for the late reply the version i'm using is recovery-TWRP-3.2.3-1003-XIAOMI8LITE-CN-wzsx150
orozcore said:
So your suggest is that I download the Pie update and let updater installs it and reflash twrp (is it the same version?)
Click to expand...
Click to collapse
Yes. Update, boot in fastboot, connect to your PC, flash TWRP and youre good to go. Mind you that version 1003 is older that the one you need. Due to bad naming scheme, the latest you want is 0212. (12 February 2019).
https://forum.xda-developers.com/showpost.php?p=78876979&postcount=46
MetallicGR said:
Yes. Update, boot in fastboot, connect to your PC, flash TWRP and youre good to go. Mind you that version 1003 is older that the one you need. Due to bad naming scheme, the latest you want is 0212. (12 February 2019).
https://forum.xda-developers.com/showpost.php?p=78876979&postcount=46
Click to expand...
Click to collapse
You might want to go with TWRP 0121 (also Pie compatible) instead, as someone reported in another thread having problems doing a restore with 0212 and nobody has yet verified if 0212 can actually do a successful restore. We are still a fairly small group here.
EDIT: Also, the stock Pie release is good. I am currently on Pixel Experience but may switch back to stock rooted at some point. Until Xiaomi releases the Pie kernel sources, no custom ROM is going to be perfect.
lexridge said:
You might want to go with TWRP 0121 (also Pie compatible) instead, as someone reported in another thread having problems doing a restore with 0212 and nobody has yet verified if 0212 can actually do a successful restore. We are still a fairly small group here.
Click to expand...
Click to collapse
Has anyone reported a successful restore with *any* version of TWRP on the Mi8 Lite? I have only seen the unsuccessful one you mentioned, and another one who couldn't restore with either 0121 or 0212. I have not tried it myself, and believe that most people are using TWRP only to flash magisk or custom roms so far.
---------- Post added at 02:39 AM ---------- Previous post was at 02:22 AM ----------
MetallicGR said:
Yes. Update, boot in fastboot, connect to your PC, flash TWRP and youre good to go.
Click to expand...
Click to collapse
The default settings in TWRP is to automatically restart the phone after an ota. As the ota overwrites the recovery with the stock version, we would normally need to reflash TWRP.
However the wzsx TWRP allows you to disable this automatic reboot in its settings. This should mean that we can reflash TWRP (and magisk if used) immediately after flashing the ota while still within TWRP, before restarting to the new system, thus avoiding the need for fastboot/PC.
This is just my theory - I haven't tried it myself as I haven't decided to do the pie ota yet.
chan200606 said:
Has anyone reported a successful restore with *any* version of TWRP on the Mi8 Lite? I have only seen the unsuccessful one you mentioned, and another one who couldn't restore with either 0121 or 0212. I have not tried it myself, and believe that most people are using TWRP only to flash magisk or custom roms so far.
---------- Post added at 02:39 AM ---------- Previous post was at 02:22 AM ----------
The default settings in TWRP is to automatically restart the phone after an ota. As the ota overwrites the recovery with the stock version, we would normally need to reflash TWRP.
However the wzsx TWRP allows you to disable this automatic reboot in its settings. This should mean that we can reflash TWRP (and magisk if used) immediately after flashing the ota while still within TWRP, before restarting to the new system, thus avoiding the need for fastboot/PC.
This is just my theory - I haven't tried it myself as I haven't decided to do the pie ota yet.
Click to expand...
Click to collapse
It is disturbing nobody has yet tested a TWRP restore. I would try it myself, but right now I cannot afford any long term downtime, as my mom is having health issues and I cannot take the chance of missing a call in case of emergency. .
Regarding flashing TWRP after update.... I certainly agree with your theory...and this could be done in either of two ways:
Method One, backup the Recovery only within TWRP. You MUST do this before taking the update!!! This lets you simply restore your existing recovery after the update. Not tested, but should work just fine assuming TWRP can indeed successfully restore (unknown).
Method Two, my personal favorite, which is what I did, was build an updated flashable .zip file of TWRP from the 1003 zip file (the only version I could find as a flashable .zip.) Just zip edit the BlaBlaBla_1003.zip file, replacing the 1003.img with the newer version 0121.img or 0212.img (after adding new .img file, delete old 1003.img file from the zip). You must also edit the /META-INF/com/google/android/update.binary (not really a binary, but actually text) to reflect the new .img filename within the zip. Update/Save zip file with new changes. Rename zip to new version name then check it to make sure your changes remained intact. Copy to phone storage. It will flash fine. Already tested. I can provide the 0121 zip file if needed, or create a 0212 flashable TWRP version as well if somebody wants it.
i havent tried cause im still waiting on bootloader to be unlocked when i check earlier i had 124 hrs
lexridge said:
Method Two, my personal favorite, which is what I did, was build an updated flashable .zip file of TWRP from the 1003 zip file (the only version I could find as a flashable .zip.) Just zip edit the BlaBlaBla_1003.zip file, replacing the 1003.img with the newer version 0121.img or 0212.img (after adding new .img file, delete old 1003.img file from the zip). You must also edit the /META-INF/com/google/android/update.binary (not really a binary, but actually text) to reflect the new .img filename within the zip. Update/Save zip file with new changes. Rename zip to new version name then check it to make sure your changes remained intact. Copy to phone storage. It will flash fine. Already tested. I can provide the 0121 zip file if needed, or create a 0212 flashable TWRP version as well if somebody wants it.
Click to expand...
Click to collapse
Why wouldn't you just flash the IMG file to the recovery partition under TWRP?
Not many people will shutdown their phones to test the restore guys. It's difficult, but we have to wait for someone to try this with the latest version of twrp. Nothing dusturbing here in my opinion. We will thank whoever tries this first that's for sure.
chan200606 said:
Why wouldn't you just flash the IMG file to the recovery partition under TWRP?
Click to expand...
Click to collapse
Interesting. I did not know you can flash img files directly with TWRP. Haha. Color me stupid!! How does TWRP know which partition to write the .img to? Does it give you a choice?
Yes it does. Choose recovery.
lexridge said:
It is disturbing nobody has yet tested a TWRP restore. I would try it myself, but right now I cannot afford any long term downtime, as my mom is having health issues and I cannot take the chance of missing a call in case of emergency. .
Regarding flashing TWRP after update.... I certainly agree with your theory...and this could be done in either of two ways:
Method One, backup the Recovery only within TWRP. You MUST do this before taking the update!!! This lets you simply restore your existing recovery after the update. Not tested, but should work just fine assuming TWRP can indeed successfully restore (unknown).
Method Two, my personal favorite, which is what I did, was build an updated flashable .zip file of TWRP from the 1003 zip file (the only version I could find as a flashable .zip.) Just zip edit the BlaBlaBla_1003.zip file, replacing the 1003.img with the newer version 0121.img or 0212.img (after adding new .img file, delete old 1003.img file from the zip). You must also edit the /META-INF/com/google/android/update.binary (not really a binary, but actually text) to reflect the new .img filename within the zip. Update/Save zip file with new changes. Rename zip to new version name then check it to make sure your changes remained intact. Copy to phone storage. It will flash fine. Already tested. I can provide the 0121 zip file if needed, or create a 0212 flashable TWRP version as well if somebody wants it.
Click to expand...
Click to collapse
I haven't noticed the restore of twpr backups failed, I only did the backup.
Can you share the flash file or the img of 0212 or 0121?
So to be clear.
* Make twrp backup
* donwload the update
* let it update and hope no lost of data
* wait to boot and enter fastboot and flash img 0212 or 0121
* flash magisk and try to test my bank apps that detect root, i couldn't hide root with magisk for these apps. (i don't need magisk so much)
I hope no mess with my phone.
MetallicGR said:
Yes it does. Choose recovery.
Click to expand...
Click to collapse
good to know you can flash a img within twpr so i'll try when I update
mr_reaper said:
i havent tried cause im still waiting on bootloader to be unlocked when i check earlier i had 124 hrs
Click to expand...
Click to collapse
Yes is bad to wait so much time and there's nothing you can do I read about the version of the unlocker but with no luck. So I finally have unlocked bootloader.
Actually v0212 is restoring, I restored data from Arrow to Havoc and no problem with that.
Just all the recoveries and roms are acting weird, I´m not sure if it´s only my device; any AOSP rom is showing bootanimation at first reboot, recovery not responding touch but then press pwr button and after that screen works normally, at time to bootup for first time screen appears totally black then press pwr to screen off and pwr to wake up and now screen is working again, luckily at second reboot all this is normalize.
---------- Post added at 10:11 PM ---------- Previous post was at 09:52 PM ----------
orozcore said:
I haven't noticed the restore of twpr backups failed, I only did the backup.
Can you share the flash file or the img of 0212 or 0121?
So to be clear.
* Make twrp backup
* donwload the update
* let it update and hope no lost of data
* wait to boot and enter fastboot and flash img 0212 or 0121
* flash magisk and try to test my bank apps that detect root, i couldn't hide root with magisk for these apps. (i don't need magisk so much)
I hope no mess with my phone.
Click to expand...
Click to collapse
If you didn´t read before a member linked to you In the post #6 both TWRP versions.
About your steps:
- No need to backup previous TWRP, just flash the new image and reboot to recovery again.
- If you already have Magisk no need to flash it again so you won´t lose root status nor any data/settings of the rom.
If you want to unroot the 0212 has this option in advanced menu.
orozcore said:
I haven't noticed the restore of twpr backups failed, I only did the backup.
Can you share the flash file or the img of 0212 or 0121?
So to be clear.
* Make twrp backup
* donwload the update
* let it update and hope no lost of data
* wait to boot and enter fastboot and flash img 0212 or 0121
* flash magisk and try to test my bank apps that detect root, i couldn't hide root with magisk for these apps. (i don't need magisk so much)
I hope no mess with my phone.
Click to expand...
Click to collapse
You should probably update your TWRP first and foremost, otherwise no access to data after you flash the update.. You will also need the Magisk Manager as an apk somewhere on your microSD card. I edited your to-do list:
* Download Magisk Manager and store on your microSD card.
* Flash new TWRP (0212 or 0121).
* Make a full twrp backup and do a recovery only backup as well
* download the update
* let it update and hope no lost of data
* Reflash img or TWRP Recovery backup 0212 or 0121
* Reboot recovery, check that you can decrypt data
* flash magisk and try to test my bank apps that detect root, i couldn't hide root with magisk for these apps. (i don't need magisk so much)
* After first boot, manually install your saved Magisk Manager app from microSD card. Run it. Check if all is good.
Do you use Titanium Backup? If so, make a full TB before doing any of this.
---------- Post added at 01:04 AM ---------- Previous post was at 12:42 AM ----------
SubwayChamp said:
Actually v0212 is restoring, I restored data from Arrow to Havoc and no problem with that.
Just all the recoveries and roms are acting weird, I´m not sure if it´s only my device; any AOSP rom is showing bootanimation at first reboot, recovery not responding touch but then press pwr button and after that screen works normally, at time to bootup for first time screen appears totally black then press pwr to screen off and pwr to wake up and now screen is working again, luckily at second reboot all this is normalize.
---------- Post added at 10:11 PM ---------- Previous post was at 09:52 PM ----------
Click to expand...
Click to collapse
Good to know that it is working for you. I will try a restore over the weekend myself, as I plan on getting rid of PE ROM. Not very happy with it, and the dev is not responding to anyone at all. I will probably just go back to stock PIE with alternate launcher.
Regarding your odd problems, I am not having any of your mentioned issues at all. My reboot times are very speedy and recovery touch has always worked from the start. I have only flashed one 3rd party ROM so far. Pixel Experience. It is actually a pretty good ROM, but the camera(s) are a bit flaky. I need my camera to work 100%. I did just install the MiX Cam, which so far is working really well. I have more testing to do before I make a decision. It seems camera apps work great for a few days, then suddenly start crashing. Ugh!
lexridge said:
Good to know that it is working for you. I will try a restore over the weekend myself, as I plan on getting rid of PE ROM. Not very happy with it, and the dev is not responding to anyone at all. I will probably just go back to stock PIE with alternate launcher.
Regarding your odd problems, I am not having any of your mentioned issues at all. My reboot times are very speedy and recovery touch has always worked from the start. I have only flashed one 3rd party ROM so far. Pixel Experience. It is actually a pretty good ROM, but the camera(s) are a bit flaky. I need my camera to work 100%. I did just install the MiX Cam, which so far is working really well. I have more testing to do before I make a decision. It seems camera apps work great for a few days, then suddenly start crashing. Ugh!
Click to expand...
Click to collapse
I never saw before this kind of weird behaviour btw is working generally speaking fine.
I´m not a fan of camera but the stock is so far better, I noticed that HavocOs rom has the feature to enable camera2 api and EIS, maybe you might try it. Regarding to use a custom launcher on stock miui rom there´s Poco launcher that keeps the same system icons than theme chosen and is very fast.
Hi Everyone,
With all of the hype around the Exynos phone its finally time for the TGY/CHC Snapdragon variants to get some attention.
No this won't work with US variants, please don't ask. This is tested on my normal s10 (SM-G9730). I'm not sure if the s10+ would work.
I've worked with a few key people to get this working. So credit goes to Flatty, Ianmacd and the creators of tomatolei rom.
This setup will let the user do the following:
-Boot/Restart phone without holding any odd button combos to boot into rooted rom.
-Hold the recovery buttons to get into TWRP.
-Not having to worry about losing root when restarting if you forget to hold your buttons, you don't need to hold anything once properly setup.
The following steps below will help you achieve a stock rom with TWRP:
1. You must be on stock rom, ideally non rooted. If you are rooted, flash your stock rom (The rom version is important, this was completed using the ASH2 version of the TGY firmware.) using ODIN (CSC HOME).
2. Once flashed boot into android and ensure OEM unlocking is enabled in developer settings.
3. Boot to download mode by turning the phone off, then press and hold the volume down button along with the Bixby key just beneath it, then press and hold the power button.
4. Flash attached TWRP from download mode. (This led my phone to boot looping). https://www.mediafire.com/file/cg8bcrf78v66v8j/LatestTomato.tar/file
5. Flash the second attached TWRP (you may have to restart and re-enter download mode again). (I believe the above flash is required too, as it likely contains vendor info). https://www.mediafire.com/file/21akg54uxqk3eix/G9730_TWRP_3.3.1-1_tomatolei-0831-v4.0.tar/file
6. Reboot phone to recovery mode (Volume up, bixby and power upon restart) which will now boot you to TWRP.
7. Flash Snapdragon muti disabler from TWRP. https://www.mediafire.com/file/opbsc7wrcr69b2v/multidisabler-samsung-1.6.zip/file *Per @FlatOutRU After flashing multidisabler you must Wipe Data (if you didn't do that before with twrp - Thanks for the clarification.
8. Boot to your rom and ensure all is well.
9. Feel free to download the latest Magisk zip and flash root from TWRP by using the recovery mode button sequence upon restart.
Sidenote: The G9730_TWRP_3.3.1-1_tomatolei-0831-v4.0.tar and tomatolei ROM also let me install PHH AOSP and PHH LineageOS
PHH AOSP microG: https://forum.xda-developers.com/pr...arm64aosp-9-0-0r21-microg-ufofficial-t3878115
PHH LineageOS: https://forum.xda-developers.com/pr...i-lineageos-16-0-gsi-arm64-ab-how-to-t3908029
Hopefully this gets a few nice Stock ROMs being produced.
Download links are added.
Fznwolf: congrat for this thread, well explained.
some question:
1) what's bring latestomato.tar ? , because no need this for me
2)magisk work for you even if you don't flash magisk_patched.tar?
3)are you able to make backup into twrp because for me it's failed. i think it work if use tomato rom but i prefer stay to tgy rom
pixiebob said:
Fznwolf: congrat for this thread, well explained.
some question:
1) what's bring latestomato.tar ? , because no need this for me
2)magisk work for you even if you don't flash magisk_patched.tar?
3)are you able to make backup into twrp because for me it's failed. i think it work if use tomato rom but i prefer stay to tgy rom
Click to expand...
Click to collapse
Thanks for the compliment @pixiebob
1) I believe the latestomato.tar has some pieces of tomato rom that allow for booting.
2) Yes, i didnt use magisk_patched.tar. I used the official magisk zip after all of my original steps as the last step.
3) I have several backups, I'm on TGY. Try start from scratch and follow my above steps using a TGY rom. Sounds like you may need to wipe and start over using the original steps provided, make sure to use the multidisabler originally attached.
Fznwolf said:
Thanks for the compliment @pixiebob
1) I believe the latestomato.tar has some pieces of tomato rom that allow for booting.
2) Yes, i didnt use magisk_patched.tar. I used the official magisk zip after all of my original steps as the last step.
3) I have several backups, I'm on TGY. Try start from scratch and follow my above steps using a TGY rom. Sounds like you may need to wipe and start over using the original steps provided, make sure to use the multidisabler originally attached.
Click to expand...
Click to collapse
you are right once multidisabler attached to your first post is installed i'm able in Twrp to backup ending without error, fantastic
pixiebob said:
you are right once multidisabler attached to your first post is installed i'm able in Twrp to backup ending without error, fantastic
Click to expand...
Click to collapse
Great to hear it's working out.
Once we root and install twrp, how we can update the phone ?
Otherwise, thanks for your work !
Yay dude thanks for using my instruction and my modified zips without asking me first
You've got an attempt before - trying to post my 9730 overlay for AOSP
Fznwolf said:
I've worked with a few key people to get this working. So credit goes to Flatty, Ianmacd and the creators of tomatolei rom.
Click to expand...
Click to collapse
No, you didn't work with other people. You just spammed me ,my pm here and in telegram to get explanation and posted it here without permission
You've also forgot one important step. After flashing multidisabler you must Wipe Data (if didn't do that before with twrp)
Multidisabler - i've just changed a few lines in @ianmacd code to get it working on our Snapdragon variant.
Twrp.tar - extracted boot.img and recovery.img from @tomatolei ROM for S10+ 9750
Thanks again @FlatOutRU I've updated the initial description to include the wipe after the muti-disabler flash as per your comments.
Hopefully this allows more work to be done on the Snap s10s!
FlatOutRU said:
Yay dude thanks for using my instruction and my modified zips without asking me first
You've got an attempt before - trying to post my 9730 overlay for AOSP
No, you didn't work with other people. You just spammed me ,my pm here and in telegram to get explanation and posted it here without permission
You've also forgot one important step. After flashing multidisabler you must Wipe Data (if didn't do that before with twrp)
Multidisabler - i've just changed a few lines in @ianmacd code to get it working on our Snapdragon variant.
Twrp.tar - extracted boot.img and recovery.img from @tomatolei ROM for S10+ 9750
Click to expand...
Click to collapse
Thank you, it works perfectly.
what Magisk version do you use ?
Is it working with magisk v20 ?
Vuska said:
what Magisk version do you use ?
Is it working with magisk v20 ?
Click to expand...
Click to collapse
I'm on 19.3, I don't see why 20 wouldn't work.
Fznwolf said:
I'm on 19.3, I don't see why 20 wouldn't work.
Click to expand...
Click to collapse
Not work in G9750 ... dont know why...
Sent from my SM-G9750 using Tapatalk
When you say flash (with only stock recovery installed) do you mean with Odin? Which boxes in odin would this tar files go to (e.g. AP, boot?). My phone is s10+ 9750. has it been tested on that? thanks a lot.
Any chance for 9700 (s10E) support?
NisseGurra said:
Any chance for 9700 (s10E) support?
Click to expand...
Click to collapse
Lets consider my method superseded by https://forum.xda-developers.com/s1...p-3-3-1-v3-t3980463/post80569455#post80569455
Thank you @Mentalmuso
heavenly86 said:
When you say flash (with only stock recovery installed) do you mean with Odin? Which boxes in odin would this tar files go to (e.g. AP, boot?). My phone is s10+ 9750. has it been tested on that? thanks a lot.
Click to expand...
Click to collapse
This would be AP, please use https://forum.xda-developers.com/s1...p-3-3-1-v3-t3980463/post80569455#post80569455
Vuska said:
Not work in G9750 ... dont know why...
Sent from my SM-G9750 using Tapatalk
Click to expand...
Click to collapse
https://forum.xda-developers.com/s1...p-3-3-1-v3-t3980463/post80569455#post80569455 will work.
Fznwolf said:
I'm on 19.3, I don't see why 20 wouldn't work.
Click to expand...
Click to collapse
Please do not use 20, it is not found to be working. Stick with 19.3.
Any luck on the 975U. I have e an unlocked VZW 975U running Android Q
Blackweiser35 said:
Any luck on the 975U. I have e an unlocked VZW 975U running Android Q
Click to expand...
Click to collapse
I see no one's responded to you in the last few days, probably because the OP says to not bother asking if it works with US variants. No there's no known way to get root on one of the 97_U variants. The bootloader is locked, and it would take a miracle to bypass that.
Cannot use Dex for PC function.
Could you upload tomatolei's twrp v6, which updated the kernel to support the Dex funtion? Many thanks!