This is a warning, I made the mistake of installing TWRP on the BOOT partition to install Magisk.
It will turn off and it will not be able to turn on, the screen will stay black, it is not possible to enter on recovery mode or fastboot. It will begin to vibrate at intervals without being able to turn it off, unless you remove the battery connection.
If you have already made the mistake of flashing the TWRP, in the forum there are some people that charges $ 12-15 for flashing through an authorized Mi account and TeamViewer.
Please, be careful.
xperneo said:
This is a warning, I made the mistake of installing TWRP on the BOOT partition to install Magisk.
It will turn off and it will not be able to turn on, the screen will stay black, it is not possible to enter on recovery mode or fastboot. It will begin to vibrate at intervals without being able to turn it off, unless you remove the battery connection.
If you have already made the mistake of flashing the TWRP, in the forum there are some people that charges $ 12-15 for flashing through an authorized Mi account and TeamViewer.
Please, be careful.
Click to expand...
Click to collapse
sometimes taking out the battery will work. but you have to disassemble the whole phone
Sent from my Redmi Note 7 using Tapatalk
xperneo said:
This is a warning, I made the mistake of installing TWRP on the BOOT partition to install Magisk.
It will turn off and it will not be able to turn on, the screen will stay black, it is not possible to enter on recovery mode or fastboot. It will begin to vibrate at intervals without being able to turn it off, unless you remove the battery connection.
If you have already made the mistake of flashing the TWRP, in the forum there are some people that charges $ 12-15 for flashing through an authorized Mi account and TeamViewer.
Please, be careful.
Click to expand...
Click to collapse
well i just did that, and i regret it
ahhl said:
sometimes taking out the battery will work. but you have to disassemble the whole phone
Click to expand...
Click to collapse
233/5000
As I said above, to stop the vibration you must remove the battery connection. You cannot remove the battery in this phone.
Formatting the boot partition implies not being able to restart. Removing the battery is useless.
loop_tunnel said:
well i just did that, and i regret it
Click to expand...
Click to collapse
Sorry mate, tell us how you have repaired?
I have same problem.
LRTeam recovery.bat made this mistake for me.
Can I solve this probem? ...or I need to throw this phone to thrash....
"...in the forum there are some people that charges $ 12-15 for flashing through an authorized Mi account and TeamViewer.
..." @xperneo please tell me where?
xperneo said:
As I said above, to stop the vibration you must remove the battery connection. You cannot remove the battery in this phone. Formatting the boot partition implies not being able to restart. Removing the battery is useless.
Sorry mate, tell us how you have repaired?
Click to expand...
Click to collapse
I ve disconnected the battery so the vibration stopped. But I can not able to formatting boot, because PC did not recognized my phone anymore. If I hold down volume up button, when reconnect USB cable, PC recognize Redmi6A for about 3 seconds, but then connection lost...I can not flash any partition... Where can I find solution?
JulianJenner said:
I ve disconnected the battery so the vibration stopped. But I can not able to formatting boot, because PC did not recognized my phone anymore. If I hold down volume up button, when reconnect USB cable, PC recognize Redmi6A for about 3 seconds, but then connection lost...I can not flash any partition... Where can I find solution?
Click to expand...
Click to collapse
I'm having the same problem, please if anyone knows how to fix it without paying someone money do tell us.
aadarsh_27 said:
I'm having the same problem, please if anyone knows how to fix it without paying someone money do tell us.
Click to expand...
Click to collapse
No way!
Official service points can help us.
however, they will only do this if you can present the purchase invoice and prove that you have purchased the device in your own country, not from China
....but if you are a very good technician then you can solve the problem.
https://www.youtube.com/watch?v=jwImRYgO4gE
https://www.youtube.com/watch?v=MoWpNL0LBEI
https://www.youtube.com/watch?v=lHug-z9EnPM
u need patch boot.img with some way to get magisk on miui pie
u can use YaAlex tools to patch ur boot.img
@wulan17 Where is YaAlexTool?
...and in your opinion: how can I use any Tool for patched boot.img if any PC can not able to recognize the Phone?
JulianJenner said:
@wulan17 Where is YaAlexTool?
...and in your opinion: how can I use any Tool for patched boot.img if any PC can not able to recognize the Phone?
Click to expand...
Click to collapse
http*://files.yaalex.tk/patcher.7z
Theres a tutorial in readme
Just flash patched boot.img with twrp
Okay.
But we have no:
-system
-boot
-recovery (twrp)
-fastboot mode
(absolutely nothing)
Tapatalkkal küldve az én ONEPLUS A6003 eszközömről
JulianJenner said:
Okay.
But we have no:
-system
-boot
-recovery (twrp)
-fastboot mode
(absolutely nothing)
Tapatalkkal küldve az én ONEPLUS A6003 eszközömről
Click to expand...
Click to collapse
Wait ur phone bricked or what?
wulan17 said:
Wait ur phone bricked or what?
Click to expand...
Click to collapse
Please read #6, #7, #8...
Phone is undead. Vibration and nothing more.
JulianJenner said:
Please read #6, #7, #8...
Phone is undead. Vibration and nothing more.
Click to expand...
Click to collapse
U need mi auth account to unbrick ur device
And read my comment clearly i give tutorial to root redmi 6a with miui pie not give tutorial to unbrick device
Yepp. I know.
Sent from my MI 6X using Tapatalk
wulan17 said:
U need mi auth account to unbrick ur device
Click to expand...
Click to collapse
Where can I find it?
xperneo said:
in the forum there are some people that charges $ 12-15 for flashing through an authorized Mi account and TeamViewer.
Click to expand...
Click to collapse
Please tell me, where can I find this people?
Im ready to pay 10 dollars. but where? and how ? help?
... I haven't found the right person for this job yet ...
Tapatalkkal küldve az én ONEPLUS A6003 eszközömről
i did unlocked bootloader, then i install twrp, patch magic, modify init.rc file to make it boot-on-charge. without any issues. i did it on stock 8, LOS 8 and 9.
i now use for permanent Android Auto in my car
Sent from my Redmi Note 7 using Tapatalk
Related
Hi,
i also brocked my Note 3...
After updating with SP Flash tools 1516 my phone does not show any sign of life...
I flashed the last chinese stable from xiaomi and SP flash finished with the green hook
Now the phone does not boot, the screen is black and if connected to the charger there is
no red light and i dont know if it charges at all
I can still repeat flashing the phone but to no avail. Connecting the phone to
usb while holding VOL +, Vol - and power there is "connecting and disconnecting"
sound from WIN7.
However Miflash does not recognize the phone anymore.
Could it be that there is a problem with the locked bootloader ?
I read some threads on Mi4 phones where they had to shorten some testpoints on the motherboard
to get the phone back to life, maybe there is a similar way for the Note 3?
I already did a lot of successfull flashing with other phones so i didnt expect any sort of problems....
Any help is really appreciated !!
Greetings
Joachim
Same problem here
Redmi Note 3 came with some unoffical multi language ROM preinstalled (7.00.11.00)
OTA did not work, downloading update onto the phone and updating via Update-App did not work either, so there was no other way than using SP Flashtool to get some official ROM on it
Downloaded official 7.0.19.0 and loaded it into SP Flashtool => Flashing went without any fault (green hook at the end) but phone doesnt do anything since then
You should untick the first option in flashtool (preloader). I had the same problem once. Here is a video which helped me and saved me device. Follow the instructions and you'll be ok. https://www.youtube.com/watch?v=A3TmXtOA0IA
arist1976 said:
You should untick the first option in flashtool (preloader). I had the same problem once. Here is a video which helped me and saved me device. Follow the instructions and you'll be ok. https://www.youtube.com/watch?v=A3TmXtOA0IA
Click to expand...
Click to collapse
It's work yes or no ? I have the same problem
same issue
i need ur help. My Redmi note 3g (Mediatek - Global rom) was stuck up at logo. When i tried flashing it using SP flash tool , i got error that "pmt changed for the rom it must be downloaded". Then i have seen some youtube videos and read forums . As per their instruction i have first forrmated using "Auto Format flash" and then did "Format all+ Download" . Now my phone is not starting.
No fastboot, no charging , No recoery mode. Only i am able to run same process again.
I am average user so dont know much about such process.. Can you guys plz help me what to do?
jalsa_100 said:
i need ur help. My Redmi note 3g (Mediatek - Global rom) was stuck up at logo. When i tried flashing it using SP flash tool , i got error that "pmt changed for the rom it must be downloaded". Then i have seen some youtube videos and read forums . As per their instruction i have first forrmated using "Auto Format flash" and then did "Format all+ Download" . Now my phone is not starting.
No fastboot, no charging , No recoery mode. Only i am able to run same process again.
I am average user so dont know much about such process.. Can you guys plz help me what to do?
Click to expand...
Click to collapse
It was a big mistake selecting "format all" option. Now everything inside your phone is deleted (including IMEI). Big problem. Who suggested you to do this?
arist1976 said:
It was a big mistake selecting "format all" option. Now everything inside your phone is deleted (including IMEI). Big problem. Who suggested you to do this?
Click to expand...
Click to collapse
i have seen some youtube videos and forums mentioning to do the same. what is the solution now?
arist1976 said:
It was a big mistake selecting "format all" option. Now everything inside your phone is deleted (including IMEI). Big problem. Who suggested you to do this?
Click to expand...
Click to collapse
jalsa_100 said:
i have seen some youtube videos and forums mentioning to do the same. what is the solution now?
Click to expand...
Click to collapse
I was in the same boat as you. The only way to revive my RN3 was to select format and download otherwise it would not turn on. I then experienced the no imei issue as you are. When I did was follow a guide which I got from en.miui.com under tips and tutorials for Redmi Note 3 where it says to permanent fix imei and worked. I never lose my imei now
help
Zehlek said:
I was in the same boat as you. The only way to revive my RN3 was to select format and download otherwise it would not turn on. I then experienced the no imei issue as you are. When I did was follow a guide which I got from en.miui.com under tips and tutorials for Redmi Note 3 where it says to permanent fix imei and worked. I never lose my imei now
Click to expand...
Click to collapse
What should i do now? will my RN3 will start again? Can u plz help?
jalsa_100 said:
What should i do now? will my RN3 will start again? Can u plz help?
Click to expand...
Click to collapse
Is it SD or MTK?
HELP
Zehlek said:
Is it SD or MTK?
Click to expand...
Click to collapse
MTK
jalsa_100 said:
MTK
Click to expand...
Click to collapse
This is what I did which worked for me
- First I downloaded so flash file
-Selected format and download in spflash
-It final booted up and I had lost Imei
-When it gets to Mi Account setup I had to select skip
-I followed THIS GUIDE
Zehlek said:
This is what I did which worked for me
- First I downloaded so flash file
-Selected format and download in spflash
-It final booted up and I had lost Imei
-When it gets to Mi Account setup I had to select skip
-I followed THIS GUIDE
Click to expand...
Click to collapse
Thanks for sharing info but its for RN3 whereas my phone is RN3G Redmi note 3G.
Hello
I tried to disable google apps on my redmi note 4 using shortcutmaker app now the phone is stuck on MI logo
My device is locked
can you please tell me how can i overcome this boot loop error
Try download or edl Mode.
Enviado do meu H60-L04 através de Tapatalk
Prolixo said:
Try download or edl Mode.
Enviado do meu H60-L04 através de Tapatalk
Click to expand...
Click to collapse
How can i get into edl mode, my device is locked .
i tried flashing with diy cable but when i release the button in cable, it says usb not recognized on pc
Got it fixed by flashing fastboot rom using DIY cable that i made myself
aaqib67 said:
Got it fixed by flashing fastboot rom using DIY cable that i made myself
Click to expand...
Click to collapse
hey ive got the same problem do you mind helping me i've tried to make a deep flash cable without succes :crying::crying:
donwalex said:
hey ive got the same problem do you mind helping me i've tried to make a deep flash cable without succes :crying::crying:
Click to expand...
Click to collapse
Bro i suggest you to go to service center if ur device is under warranty they will fix the issue in much better way rather than going with deep flash cables :silly:
donwalex said:
hey ive got the same problem do you mind helping me i've tried to make a deep flash cable without succes :crying::crying:
Click to expand...
Click to collapse
If the service Centre is available in your city then you should go there and they will fix it for you but if it's not available just like in my case then watch few videos on YouTube to make the deep flash cable and if you are too lazy to do it then Show the video to any electrician or someone who knows soldering. Good luck
Hello, i got a big problem and needed HELP!
Today i got my Note 4...
so i tryed to unlock the bootloader, bad thing did not logg in at the device.
i booted the mobile in fastboot mode and started the official unlock tool.
until 50% it went quite well then i got an error message:
couldn't verify device
current account is differnet from the account info on the device
so i tryed to boot again but was in a bootloop...
i tryed also flashing a new rom (nikel_global_images_7.4.14_20170414.0000.00_6.0_global_b5d5f15e0e.tgz) and again i got an error
"flash boot error"
hope somebody can help
p.s. sorry for my poor english
Following
Did you read this?
dao80 said:
...i tryed also flashing a new rom (nikel_global_images_7.4.14_20170414.0000.00_6.0_global_b5d5f15e0e.tgz) and again i got an error...
Click to expand...
Click to collapse
Are you sure you are using MTK Variant?
akil777 said:
Did you read this?
Are you sure you are using MTK Variant?
Click to expand...
Click to collapse
yes im sure, i tryed this already and still in bootloop
althoug it says download ok
dao80 said:
yes im sure, i tryed this already and still in bootloop
althoug it says download ok
Click to expand...
Click to collapse
Did you use Sp flash tool?, if yes You should tick all except preloader. You will have to wait 5-15mins for the phone to boot up.
akil777 said:
Did you use Sp flash tool?, if yes You should tick all except preloader. You will have to wait 5-15mins for the phone to boot up.
Click to expand...
Click to collapse
yes i used this tool, after rebooting the mi logo is on the screnn for about 7 secounds then the mobile boots again and again...
;(
dao80 said:
yes i used this tool, after rebooting the mi logo is on the screnn for about 7 secounds then the mobile boots again and again...
;(
Click to expand...
Click to collapse
I have never experienced that.. I think you should send it to your mobile repair center.. Be patient,, It might take few days. Don't panic,
akil777 said:
I have never experienced that.. I think you should send it to your mobile repair center.. Be patient,, It might take few days. Don't panic,
Click to expand...
Click to collapse
i m already looking for a mobile repair center here who can repair xiaomi mobiles...
but so fare all numbers i called are not in service anymore or dont repair xiaomi...
dao80 said:
i m already looking for a mobile repair center here who can repair xiaomi mobiles...
but so fare all numbers i called are not in service anymore or dont repair xiaomi...
Click to expand...
Click to collapse
check this http://en.miui.com/thread-491655-1-1.html
You tried putting phone in fast boot mode (volume down then power). Then just flash the stock firmware?
robjbw said:
You tried putting phone in fast boot mode (volume down then power). Then just flash the stock firmware?
Click to expand...
Click to collapse
yes i tried china and global
but only bootloop
but to be on the save side, where to i find a the stock rom (flashable with the miflashtool)?
dao80 said:
yes i tried china and global
but only bootloop
but to be on the save side, where to i find a the stock rom (flashable with the miflashtool)?
Click to expand...
Click to collapse
flash done with mi flash? If got error then try with deep flash cable. see yt tutorials
itsmedRb said:
flash done with mi flash? If got error then try with deep flash cable. see yt tutorials
Click to expand...
Click to collapse
deepflash is also possible for mtk devices?
robjbw said:
You tried putting phone in fast boot mode (volume down then power). Then just flash the stock firmware?
Click to expand...
Click to collapse
tried it again with the mi flash tool i got following error
80x80004005: FAILED (remote: download for partition 'boot' is not allowed
Hey Guys, i soveld the problem...
AND F**K it was a quite easy solution...
i tried so hard was crying and a kind of very desperate...
anyways i aslo wrot a mail to mi and they did not help at all...
they even say i should lock in at the device if im in a bootloop, kinda funny?
anyways so i drained the batterie and nearly about to give up this device....
BUT i give it one last try, plugt it in and booted it... it took a while but after a while i finaly was able to boot the Phone and set it up...
so this threat can be closed...
thank you guys for your help
When i flashed the Evolution X Rom to Stock rom It Got Failed And My Device Is Not Turning ON.
Whenever I Tried To Install stock Rom using mi flash tool It Is Saying "Cannot Recieve Hello Packet" & write time out,maybe device was disconnected Please Help ME To Fix
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
papsr6 said:
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
Click to expand...
Click to collapse
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
wetito said:
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
Click to expand...
Click to collapse
I Had Tried EDL flashing from Unlock Tool Flashing Done Perfectly But Formatting Failed..Is it a partition error ?.. The Display is not turning on.. No Signal Only The Signal is Entering EDL mode
wetito said:
Is not completly true... When the edl error "... Hello packet" appear is impossible. I also recived it when i tryed to make mia3-cce9 conversion. I retry many times but no success. Qualcomm port works, miflash connection works... But it's impossible to flash. I have searched every where on internet without succes. For me only fastboot flashing mode work. Not edl... I think this hello package is a software restriction of xiaomi. But i don't understand why some devices can bypass it and other fails
A question: you can enter in fastboot? I'm not sure you have try. Is the more simply solution. It's improbably that evolutionx had erase the bootloader... Connect phone to pc, then press power+vol- if you will see the xiaomy avatar.. you can recover the system. An advice for you: before flash a custom rom read with attention the guide. I suppose you haven't do this. And your modding level is low...
Click to expand...
Click to collapse
papsr6 said:
The device is off?
Try to hold volume down and up at the same time and connect the usb cable to see if going to EDL mode.
If going to EDL mode you can flash a stock rom from edl with miflash.
Click to expand...
Click to collapse
My Phone Is Now Like This :
hishamhsm said:
I Had Tried EDL flashing from Unlock Tool Flashing Done Perfectly But Formatting Failed..Is it a partition error ?.. The Display is not turning on.. No Signal Only The Signal is Entering EDL mode
Click to expand...
Click to collapse
What you wrote is not good... I don't know unloock tool. But before use this applications is necessary read carefully the instructions. It seems you didn't have do this. Good luck. Ps: if your phone boot into fastboot reflash stock via miflash... If you don't have made a big damage it will work. Very import is select the correct slot before flash... In my case i always select slot a to make a clean and safe installation
wetito said:
What you wrote is not good... I don't know unloock tool. But before use this applications is necessary read carefully the instructions. It seems you didn't have do this. Good luck. Ps: if your phone boot into fastboot reflash stock via miflash... If you don't have made a big damage it will work. Very import is select the correct slot before flash... In my case i always select slot a to make a clean and safe installation
Click to expand...
Click to collapse
is mi authorized account needed
hishamhsm said:
is mi authorized account needed
Click to expand...
Click to collapse
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
wetito said:
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
Click to expand...
Click to collapse
no fastboot , no charging
wetito said:
Probably... Mee to i found this... But via fastboot is not necessary. Only with edl cold be necessary
Click to expand...
Click to collapse
will you help me to flash my phone via teamviewer
Sorry if you have damage bootloader (so fastboot don't work), the only way is edl. But i don't know how to solve edl flash fail. You had ask to other user, or search with Google. Or i'm afraid for you... Buy new phone. For the future if you want modding... Do it carefully
wetito said:
Sorry if you have damage bootloader (so fastboot don't work), the only way is edl. But i don't know how to solve edl flash fail. You had ask to other user, or search with Google. Or i'm afraid for you... Buy new phone. For the future if you want modding... Do it carefully
Click to expand...
Click to collapse
Thanks Bro Thanks For Your Support,.... Love From Kerala , India
Good luck
Same thing happened to me then i went mi authorised service centre and they charged 179rs and now my phone is working fine
azeem_saifi0411 said:
Same thing happened to me then i went mi authorised service centre and they charged 179rs and now my phone is working fine
Click to expand...
Click to collapse
is that phone under warranty while it was bricked
hishamhsm said:
is that phone under warranty while it was bricked
Click to expand...
Click to collapse
Sorry no. You have the bootloader unlocked... If your restore via edl will fail, in my opinion the best choice is buy a new phone. I don't know in your country. considerating that motheborard is not damaged... But phone must be open... The minum cost of this repair i think could be 100 € (convert in your currency). On YouTube there are a lot of tutorial how to do by yourself... But i'm not shure you have all skills...
wetito said:
Sorry no. You have the bootloader unlocked... If your restore via edl will fail, in my opinion the best choice is buy a new phone. I don't know in your country. considerating that motheborard is not damaged... But phone must be open... The minum cost of this repair i think could be 100 € (convert in your currency). On YouTube there are a lot of tutorial how to do by yourself... But i'm not shure you have all skills...
Click to expand...
Click to collapse
I Have Given It to A repair shop. They told me that that is emmc/UFS chip issue. So they will reprogramme the chip fix it and give the phone to me... They Told that it should fix..
Anyway I'm from India
hishamhsm said:
I Have Given It to A repair shop. They told me that that is emmc/UFS chip issue. So they will reprogramme the chip fix it and give the phone to me... They Told that it should fix..
Anyway I'm from India
Click to expand...
Click to collapse
I suppose that was the problem. I hope the repair shop in india are cheapest than in italy for the future... Make Modding with care
wetito said:
I suppose that was the problem. I hope the repair shop in india are cheapest than in italy for the future... Make Modding with care
Click to expand...
Click to collapse
Repairing cost around 10dollars . In India repairing cost is low but the price of mobile phones and spare parts are too high due to tax.
Thank you so much for your help and support bro. Love From India❤❤
can someone please help hard bricked brand new moto edge nothing will do anything no matter what try black screen. i'll pay someone to help please!! thanks
ThirteenSeasons said:
can someone please help hard bricked brand new moto edge nothing will do anything no matter what try black screen. i'll pay someone to help please!! thanks
Click to expand...
Click to collapse
If you have a pc, see if it's in EDL Mode
Is my device in EDL Mode?
sd_shadow said:
If you have a pc, see if it's in EDL Mode
Is my device in EDL Mode?
Click to expand...
Click to collapse
it is so how do i fix please???!!1 i'll legit pay you whatever want lol
sd_shadow said:
If you have a pc, see if it's in EDL Mode
Is my device in EDL Mode?
Click to expand...
Click to collapse
it is how do i fix
ThirteenSeasons said:
it is so how do i fix please???!!1 i'll legit pay you whatever want lol
Click to expand...
Click to collapse
??
ThirteenSeasons said:
it is how do i fix
Click to expand...
Click to collapse
You have 2 possible options
1. You can wait several days for the battery to die, then connect to a wall charger.
It may boot normally, this is the safest thing to try.
2. Use a blankflash there is one available for XT2061(burton) devices
https://mirrors.lolinet.com/firmware/moto/burton/blankflash/
download the blankflash, unzip it and
run the blank-flash.bat
If the blankflash works, the device will reboot, you may need to reflash firmware with fastboot or LMSA
sd_shadow said:
You have 2 possible options
1. You can wait several days for the battery to die, then connect to a wall charger.
It may boot normally, this is the safest thing to try.
2. Use a blankflash there is one available for XT2061(burton) devices
https://mirrors.lolinet.com/firmware/moto/burton/blankflash/
download the blankflash, unzip it and
run the blank-flash.bat
If the blankflash works, the device will reboot, you may need to reflash firmware with fastboot or LMSA
Click to expand...
Click to collapse
I accidently flashed moto g power into it when it's edge +... What if neither of those fix it? It's been unplugged for days. Idk if the bttrys dead cause no screen... Do you think fixable ?
ThirteenSeasons said:
I accidently flashed moto g power into it when it's edge +... What if neither of those fix it? It's been unplugged for days. Idk if the bttrys dead cause no screen... Do you think fixable ?
Click to expand...
Click to collapse
Ok, that's info you should have shared first.
Letting the battery die won't help.
Your only option is blank flash, but no guarantee that it'll work.