I'm searching for parts to fix my Galaxy View. It needs a charging receiver and wire harness going to the first connection right after the plug-in located on the side. The wire harness needed is not much more than 1/2 inch long. The wires are so small, replacing them any other way than with OEM impossible. Until I get the parts I'm stuck using an G. tab with a 10.4inch screen.
If anyone knows of a website that sells tablet parts. Please post the links or send a message
Thank You
there is a listing for internals only for galaxy view on ebay.
am i allowed to post link ? not sure..
mrbogusbaxter said:
there is a listing for internals only for galaxy view on ebay.
am i allowed to post link ? not sure..
Click to expand...
Click to collapse
Sorry been building new house and moved fo temp digs. I'm still in need of parts link on ebay. Send it in a PM if uncomfortable posting link openly.
Thanks
Related
Need help!!!
Smashed my LCD and orded a replacement from HK. The part number they sent me was 60H00037-00M. After installing it, all I get is a white screen. Sent it back and recieved another one with the same number and again the same deal!!!
The part number Im chasing is 60H00056-00m or TX0704APAA1. I think it is a mfg by Hitachi.
I cant find anything with this part number on the net and was wondering if anyone knows if there is an equivalent that could be used insted.
Mal..
Are you sure that your connections are secure and lined up properly? I replaced the screen on my 8525 and the ribbon cable was not connected properly the first go round. It is the one with the tiny screws.
teknics said:
Are you sure that your connections are secure and lined up properly? I replaced the screen on my 8525 and the ribbon cable was not connected properly the first go round. It is the one with the tiny screws.
Click to expand...
Click to collapse
Teknics, are yoy refering to the two incy wincy screws that fasten the ribbon to the d-pad at the bottom?
Mal..
Yes that cable, but also make sure the ribbon cable that slides into the locking connector on the main board is in properly also.
HK?????
hi all
i have been looking for a replacement rear speaker and a front facing camera for my phone and so far the only leads i have been able to get is to look on ebay for someone selling their damaged phone for parts. you mentioned a HK in your first post is that a place to buy Hermes spare parts and if so is there a minimum amount that you have to buy?
sllabymkcus said:
hi all
i have been looking for a replacement rear speaker and a front facing camera for my phone and so far the only leads i have been able to get is to look on ebay for someone selling their damaged phone for parts. you mentioned a HK in your first post is that a place to buy Hermes spare parts and if so is there a minimum amount that you have to buy?
Click to expand...
Click to collapse
HK refers to Hong Kong you can purchase screens and digitizers that i know of but as far as small inexpinsive electronics i think your sol. just out of curiousity did you manage to blow the speakers or what? i have played some pretty loud music through my hermes using mortplayer and have not managed to blow them yet.
I have 60H00056-00m or TX0704APAA1 LCD.
msn:[email protected]
I am looking for a TX0704APAA1 for my HTC Tytn.
Apparantly this is the Hitachi model other models are also available on ebay (Samsung and Toppoly). As I understand Samsung and Toppoly are not compatible with one another apparently they use different controllers.
As for the Hitachi I have know idea whether it is compatible with Samsung or Toppoly, which is why I am on my quest after the Hitachi...
Anyone know where I can get one?
I think this one might work.
http://cnn.cn/shop/8525tytn-screen-p-1704.html?osCsid=37d6ea546d0b93a035876bf59f229d3b
The 60h00032 or 60h00037 did not work on my dopod 838 pro.. I just got a white screen.
I'm hoping someone can help me out here.. For some reason the infrared port cover on the bottom of my Hermes is missing. It's the black plastic piece thats on the left of the soft-reset button. Anyone happen to know where I can purchase a new one? Dust, etc. gets into it and it may cause problems.
Anyone know where to get one?
a broken 8525 or tytn or any other family member on ebay? This woudl benefit because you have other pieces as spares just incase.
Hey, i would even send you a few dollars for the little black round plug that covers the antenna port on the back of the phone (I'm currently using a black pencil eraser).
you could also buy a replacement OEM case from the company that has been linked on this forum a few times.
ryaske said:
a broken 8525 or tytn or any other family member on ebay? This woudl benefit because you have other pieces as spares just incase.
Hey, i would even send you a few dollars for the little black round plug that covers the antenna port on the back of the phone (I'm currently using a black pencil eraser).
you could also buy a replacement OEM case from the company that has been linked on this forum a few times.
Click to expand...
Click to collapse
Hmm very good idea. I didn't even think about that. Thank you for the advice. I will let you know if I get one
Hi, is there any chance to get Topaz disassembly guide?
THX
Edit: Dont need it anymore, I have done it, not difficult at all (similar to Nokia phones). HTC made Topaz very easy to disassembly.
I was cleaning part between digitizer and LCD from dust with antistaic brush and compressed air.
There are just 3 connectors to disconnect mainboard (digitizer, phone receiver and LCD), to get to the LCD. No coaxial cables to connect GPS and bluetooth antenna (all just by touch connectors to the black plastic top back part), Chipset is covered by metal plate, cant see it.
LCD: S/N: 1EJV093Q000069
P/N: 60H00209-00M S508
Can I request you get some high res photos of the PCB/LCD and/or record the ic part numbers while you've got it apart? It would be really useful to know for Linux/Android development.
Can you post what kind of gps chipset is buildin ?
Thanks in advance
Daniel
Thanks for the photos! Would you be able to post a higher res version of the 3rd one or simply scribe what is written on the back of the LCD. I'm hoping the serial number might give an indication of the chipset used in the LCD.
cheers!tsy
So you can sure tell us if the front frame is really metal or plastic ?
Its metal body iside of plastic housing.
Great job !
Thanx
some instructions or tips of how you disassembled it would be nice
i unscrewed my diamond2, and i cannot find a way to disassemble it..
help!
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
i found a htc service manual for diamond 2 that was leaked
not sure if i can post it here..
it explains how to disassemble the device
EDIT: I am so sorry, the leaked document is the user manual, it is incorrectly posted as the service manual in many sites. sorry
post it! what's the worst they can do... tell you to remove it?
PhilipL said:
Hi
Nice work and photos.
One problem that has been reported, and I assume it was something you suffered from, is dust entering through the volume rocker and finding it's way onto the LCD display.
This seems rather an oversight by HTC as usually the LCD panel would have some form of seal or bezel (sticky or foam) to stop dust. Does the LCD panel have anything like this at all?
Regards
Phil
Click to expand...
Click to collapse
Look here:
http://forum.xda-developers.com/showthread.php?t=520795&highlight=solution%21%21%21
Sticky? New Thread? & Help
I think we either need to sticky this, or make a new thread that encompasses all disassembly / dust leak information about the topaz.
I still cannot disassemble my device, i wish someone could help :/
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Guinea.Pig said:
Disassembling the Diamond 2 is really simple.
Remove the 4 T5 screws at the four corner
Remove the small plastic cover below the battery (might be optional)
Pop the main plastic body off the face piece (I use a really small flat screw driver) Starting from the top of the device
Remove the 3 connection then pop the main board
Remove the 4 hardware buttons then remove the LCD screen
I'll try to take some pictures when the new LCD screen arrives...
Click to expand...
Click to collapse
Thanks for the steps. I just yesterday disassembled my TD2, but didn't dare remove the connections on the mainboard. The one on top left (see your pic mainboard.jpg) is no issue, but the other ones are tricky...or at least I thought they are. I couldn't figure out how to exactly remove those connectors. Could you maybe give some steps or info on how to remove those connectors? Thanks again for your help.
disassembly
thanks for the update . ill try and post pictures up when possible.
I am interested in this too, I have dropped mine a couple of times and am looking to replace the housing (although I have already been ripped off once by buying a repaired one on ebay).
So any idea where I can get a legitimate full housing and a guide to moving the guts from one to another?
Cheers,
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Awesome
stormyuk said:
Found this:
http://www.pdacenter.ru/razborka/htc-touch-diamond2/
Now I just need to find a genuine and complete housing.
Click to expand...
Click to collapse
Thanks for your contribution stormyuk !
You can find housings on ebay, though most don't come with the buttons.
I bought one and its practically impossible to distinguish any differences,
Buy from kr-net on ebay its the seller that sold me my housing
Sorry for my poor english.
I have to replace back hard cover (and aluminium frame) of my TF101 but I don't know where to buy it, anyone can help me?
h**p://m.zdnet.com/photos/cracking-open-the-asus-eee-pad-transformer-tf101/6272908?seq=12
Thanks in advance
The quality of construction of these parts are very poor (the joint parts break themeselve so easily) so I'm happy if there is other brand (not asus) that produce them
Try here
http://www.asusparts.eu/index.php?cPath=66920_222155_222301_222308
Thanks,
it's exactly I was looking for... but 50,44 euros for the alluminium frame are a theft!
Most TF's that are unfortunate enough to suffer some kind of trauma ends up with a broken or cracked screen. I'm surprised you can't find a replacement screen anywhere... at all.
goodintentions said:
Most TF's that are unfortunate enough to suffer some kind of trauma ends up with a broken or cracked screen. I'm surprised you can't find a replacement screen anywhere... at all.
Click to expand...
Click to collapse
You can get the LCD screen here.
pbtran said:
You can get the LCD screen here.
Click to expand...
Click to collapse
It's the glass digitizer that's the problem getting.
baseballfanz said:
It's the glass digitizer that's the problem getting.
Click to expand...
Click to collapse
and thats what i need for one of my TF, glass intact but under it is cracked
Has anyone found a cheaper alternative for the bezel? I figured it would be like 10 bucks when I tore mine off out of frustration over the sticky power button... now the back is falling off lol.
Also want to buy the bezel.
C'mon, china brothers, start to make them! You will have million orders!
on Asusparts.eu with shiping it costs 71 Eur. ... Almost $100 for cheap aluminium frame ... Will their bezel do BJ ?
As of lately, is there anyone who has found a site in the USA which sells the parts? Don't really want to order my part from Sweden... I need a Power/Volume daughter board, its about $89 shipped from sweden... really want it sooner than 5-6 weeks.
Need some help to find 40-Pin Female socket for my tablet
Dear All:
I do have a problem with the female socket in the Asus EEE TF101
in first I thought that the problem in the charging cable and I replace it but looking into the female connector in the bottom of the tablet I could see some burn inside the socket
need to but this female socket
can any one help me with where to find this part and part no if possible
Thanks
parts4repair dot com
ran across this place with screen+digitizer $40 and LCD $40
thought id post it up
sameh71 said:
Dear All:
I do have a problem with the female socket in the Asus EEE TF101
in first I thought that the problem in the charging cable and I replace it but looking into the female connector in the bottom of the tablet I could see some burn inside the socket
need to but this female socket
can any one help me with where to find this part and part no if possible
Thanks
Click to expand...
Click to collapse
search on ebay my friend.
Did you try alibaba? It's a Chinese website where you can sell and buy parts.
Sent from my HTC Vision using xda premium
I actually oredered the colume ctrl pcb from auasparts.eu ... 4-8 weeks to the USA but for $49US I have my part. Got the tablet for free so no complaints here lol
Posted using XDA Premium from my Galaxy Note 2
Mod Edit links removed
Thank you, do you have USB plug charge board?
jeallybean said:
Thank you, do you have USB plug charge board?
Click to expand...
Click to collapse
Thx for like. the replace parts of K3 Note is rare, i don't see USB plus charge board in stock; while i found, i would add.
Due to my girlfriend's careless, her k3 note had dropped, and the top glass had cracked, anyone know where to buy a new one? very thx.
Have anyone tried to buy one screen from the seller? Im not found of forking out some bucks and then get so called original parts that are more or less junk.
Tomas Harris said:
Due to my girlfriend's careless, her k3 note had dropped, and the top glass had cracked, anyone know where to buy a new one? very thx.
Click to expand...
Click to collapse
hello, don't see the top glass of K3 note, maybe you need buy K3 note lcd screen.
---------- Post added at 09:48 AM ---------- Previous post was at 09:45 AM ----------
kongha said:
Have anyone tried to buy one screen from the seller? Im not found of forking out some bucks and then get so called original parts that are more or less junk.
Click to expand...
Click to collapse
i had bought a battery for my K3 note phone, it uses well, and delivery fast.
WHo knows where to buy the screen?