I have a Jabra 350BT headset and a newly purchased Cingular 8525. I have installed Microsoft Voice Command on the phone, but the headset does not do anything when the button is pressed. I would like to enable the Voice Command.
Has anyone developed a way to get this to work with the 8525?
Thanks!
By the way, I have Microsoft Voice Command 1.6.
Disregard this post. I found the thread about the BT headset hack.
Related
Hi, i have the Underground WM6 ROM, and installed the Cyberon Voice Dialer 1.1 (the some that come with my WM5 from factor room), and when i press the the headset, to say a voice command, just the phone (with WM6) show my the dial pad, but not the windows from Cyberon to say the command, early when i used the WM5 Room, that work fine.
And another little cuestion, on WM5 i installed a soft that permit redirct all the audio from the device acroos the bt audio to the bt headset, on WM6 this soft works but (as ex.) when i open de PocketMusic, o WM Player, works fine, but when i close these software (the players), close also the redirection of the audio to the bt headset, some one know some trick to it do not pass again ? or works as WM5 room.
Thank's a lot.
PD; I see o some post, some file .cab that permit that when ones press the bt headset works the Cyberon, but i lost these post.
Ok so I have a Motorola H3 headset and am trying to use it with my X01HT. I have it paired up and it brings it up as a hands free device. I have LSVW WM6(4/08) w/ new A2DP driver. Ok anyways, I could listen to music on the headset when it was paired with my Compaq H6315 yet it won't work with the X01HT. Does anyone know of a possible fix?
I have the same question that is X01HT support A2DP profile? I am preparing to buy a headset.
Well the thing is, if I push the button on my headset it opens the voice shortcut program, and if I have WMP in the background playing a song it will switch from speaker to headset for about 2 seconds and then go back to the speaker. This tells me it should be able to stream music to the headset.
Hi,
is there possibility to use an headset to set a voice command.
Are there any exeperince.
Greets Fraggy
Sort of!
HTC have changed the Bluetooth stack and it's causing problems, people here are looking at it, but I suspect we won't see a fix till we get some cooked ROMS.
If you press and hold the send key on the phone you should hear the familiar voice command two tone in your headset and can then speak the command, I'm using this with my car kit to initiate calls successfully. It does not appear to be possible to trigger VC from the headset right now.
Hope that helps,
Gordon
same problem for me with volume control: my BT stereo headset does not have volume control keys, so I can only use the keys on the phone. this was smoothly working with TP1 (Raphael). now it does not work AT ALL with TP2 :-(
could it be possible to deactivate the widcomm stack so we can use M$ stack
I'm just checking if this will work
deleting...
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ControlPanel\Overrides]
"Bluetooth"="\Windows\BTConfigCE.cpl"
[HKEY_LOCAL_MACHINE\ControlPanel\Bluetooth]
"Redirect"="BTConfigCE.cpl"
ok didn't work but now i have windows mobile controlpanel too
I have owned several phones all had Microsoft Voice Command 1.6 installed. I fell in love with it. I have it installed on my TG01, however all the announcements and voice commands route through the device and not the BT headset. Once the call is being made it goes through the headset.
Thoughts?
Has anyone successfully used a bluetooth headset with Microsoft Voice Command with a stock 1.66 ROM? When I press the headset button, the voice command program initiates but all audio in/out happens on the handset microphone/speaker and not the headset. I have read where the widcomm bluetooth stack is to blame. I have also heard that some custom ROMs work ok.
I have tried the MSVC patcher to 28008 on top of msvc 1.6.21725 but it has not helped.