Related
How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!
hey))) as promised, the Soft-SPL and Hard-SPL
1. Soft SPL - loaded to ram temporarily, erased after reboot, use it to flash HardSPL or tested working roms.
2. Hard SPL - A version which is flashed to rom.
So, what`s this?
1. Based on oxygen spl, but
1. Doesn`t check CID
2. KeyCard security is reset
3. Allows to flash unsigned (custom) nbh files.
http://rapidshare.com/files/65732449/hspl.7z.html
Instructions:
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen
2. Connect USB to pc
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
p.s. sorry, have problems with wm6 - no info when i`ll finish it
Good Jobs :d
THANX SPV3DEV foor tool . WM6 for tis device ?
THANK YOU GREAT JOB. not tested yet. but thanks for the efforts.
how is WM6 comming as you promised?
sp3dev,
Thanks I have CID unlocked my phone.
Please I need to SIM unlock it.
how I can do it?
Please help.
Doesn't work for me.
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
You passed in boot mode? Long push camera and short power.
No...I didn't pass. Phone has white screen, when I run RomUpdateutility.exe before flashing shows me error.
Have ideo when your WM6 rom will be finish ?
Thx for the tool , great job .
wm6
HI. Please Guide coking rom for Htc S310? Thanx
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
I've this problem too. Running windows vista aswell. Anyone found a solution?
RUU on vista
the solution is here:
http://www.modaco.com/content/Windo...U-on-Vista-It-can-be-done-the-ultimate-guide/
Hello all
my phone is fully unlocked
i soft-spl my orange c100(htc 310) and when i tried to hard-spl it just crashed wile writing the new spl
now i am stuck at tri-color boot screen
Does somebody have orange c100 romania rom?
Thanks
Maybe you will help me...
sp3dev said:
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
[/QUOTE=sp3dev]
Hello!
Maybe you Sir have an official Oxygene ROM image? Maybe you dumped it for yourself before all thos updates? I am extremally looking for it Please let me know if you could send it or upload somewhere.
Best greetings,
RA
Click to expand...
Click to collapse
Hi,
Where do I place hard spl?
When pressing this I first press camera and then open spl.ink ? Or is there another way I should do this?
i am from romania and i have spv c100.
if you could tell me how to back-up my rom i will help you.
hi SP3DEV
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
charlietruong said:
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
Click to expand...
Click to collapse
same problem.. any solution?
Cease & Desist!
Hard-SPL is *MY* trademark, I never said you could use it.
PSYCHE!
just kidding, but tell me sp3dev, when you disasm the SPL; are you actually rebasing the file, or just going at it by trial and error... because it shouldn't take more than 5 minutes to hack up a Hard-SPL and SSPL.
Also... really you should only call it Hard-SPL if it prevents itself from being overwritten, otherwise it's just a USPL... not that I particularly mind.
Hi,
I've read and reread the thread at http://forum.xda-developers.com/showthread.php?t=350033 i.e. New WM6 Upgrade Guide.
Just a few questions:
1. After step 2 i.e. HardSPL is complete, what should be the status of the prophet? I mean.. at the end, would it soft reset? hard reset? the screen will remain blank? tri color? How would I know the step is completed successfully?
2. Step 5: Flash the nk.nbf. Ok.. now how should the prophet be connected? Will the prophet be in a wm5/6 setup stage, and a guest connection would have to be made thru activesynch, just like the previous process? What state would the prophet be in from previous step, and how and when to run the ROMUpdateUtility_NV_G3.exe? It is understood that my nk.nbf is in the same directory.
TIA.
J_Kirk said:
Hi,
I've read and reread the thread at http://forum.xda-developers.com/showthread.php?t=350033 i.e. New WM6 Upgrade Guide.
Just a few questions:
1. After step 2 i.e. HardSPL is complete, what should be the status of the prophet? I mean.. at the end, would it soft reset? hard reset? the screen will remain blank? tri color? How would I know the step is completed successfully?
2. Step 5: Flash the nk.nbf. Ok.. now how should the prophet be connected? Will the prophet be in a wm5/6 setup stage, and a guest connection would have to be made thru activesynch, just like the previous process? What state would the prophet be in from previous step, and how and when to run the ROMUpdateUtility_NV_G3.exe? It is understood that my nk.nbf is in the same directory.
TIA.
Click to expand...
Click to collapse
1. look the same (nothing change), only the digits was being changed while rebooting...
2. USB cable to connect, you can let it be in guess connection with the activesync or if problems occur, have a look to post 1 in my thread ( in my signature) for your reference..
Good luck....
again..... master rondol1 provides detailed answers, look below, enjoy~~~~~
J_Kirk said:
Hi,
I've read and reread the thread at http://forum.xda-developers.com/showthread.php?t=350033 i.e. New WM6 Upgrade Guide.
Just a few questions:
1. After step 2 i.e. HardSPL is complete, what should be the status of the prophet? I mean.. at the end, would it soft reset? hard reset? the screen will remain blank? tri color? How would I know the step is completed successfully?
2. Step 5: Flash the nk.nbf. Ok.. now how should the prophet be connected? Will the prophet be in a wm5/6 setup stage, and a guest connection would have to be made thru activesynch, just like the previous process? What state would the prophet be in from previous step, and how and when to run the ROMUpdateUtility_NV_G3.exe? It is understood that my nk.nbf is in the same directory.
TIA.
Click to expand...
Click to collapse
1. Your Prophet will restart to the same OS as you had before. There is no change other then the SPL replaced. You can check this on the second startup-screen, the one with the red informationtext. If things went fine, you should read: SPL 2.G3.4PDA or SPL 2.G4.4PDA. If not, don't continue flashing but try to install HardSPL again.
2. As the OS is still the same you used before, just connect your PPC using an USB cable. No need to connect in guest mode or anything different. When made sure that HardSPL is installed correct, the Prophet doesn't have to be in a special state. You have downloaded the RUU according to your devicetype G3 or G4. Download the nk.nbf ROM file of your choice and place it in the same folder with the RUU. Now just run the RUU and be patient. It seems to stop several time, but just don't react as long as you don't get an error. At the and the RUU will report it is finished and your Prophet will restart.
rondol1 said:
1. Your Prophet will restart to the same OS as you had before. There is no change other then the SPL replaced. You can check this on the second startup-screen, the one with the red informationtext. If things went fine, you should read: SPL 2.G3.4PDA or SPL 2.G4.4PDA. If not, don't continue flashing but try to install HardSPL again.
2. As the OS is still the same you used before, just connect your PPC using an USB cable. No need to connect in guest mode or anything different. When made sure that HardSPL is installed correct, the Prophet doesn't have to be in a special state. You have downloaded the RUU according to your devicetype G3 or G4. Download the nk.nbf ROM file of your choice and place it in the same folder with the RUU. Now just run the RUU and be patient. It seems to stop several time, but just don't react as long as you don't get an error. At the and the RUU will report it is finished and your Prophet will restart.
Click to expand...
Click to collapse
Thanks very much, rondol1 !!
dioxda2 said:
Thanks very much, rondol1 !!
Click to expand...
Click to collapse
Hahaha, why is it that we anwer the same questions at the same time so often??!
Thanks a lot rondol1 and dioxda2! your answers are just what i needed..
Ok a brief followup.. after downloading the update package from http://forum.xda-developers.com/showthread.php?t=350033&highlight=hard+spl and applying the G3 version of HardSPL, I see absolutely NO change on my prophet. The boot up shows SPL 2.20.0000 and not SPL 2.G3.4PDA as mentioned. I've tried it twice with same result.
Any suggestions?
J_Kirk said:
Ok a brief followup.. after downloading the update package from http://forum.xda-developers.com/showthread.php?t=350033&highlight=hard+spl and applying the G3 version of HardSPL, I see absolutely NO change on my prophet. The boot up shows SPL 2.20.0000 and not SPL 2.G3.4PDA as mentioned. I've tried it twice with same result.
Any suggestions?
Click to expand...
Click to collapse
did you try THIS TOOL on my Thread?
After Hardspl,
Try this "one step Jumpspl+Korand3.1(WM6.1)" tool (uploading), quite convenient.. to try this rom. ( clean, fast and stable)
I was trying to make upgrade from wm5 to wm6,and was looking in tutorial xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide. First,I found a Upgrade_HardSPL_G4.rar, and did what was said in tutorial,copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,Execute the SPL.lnk IN THE DEVICE, then you see Prophet in all bright or white screen,Execute the ROMUpdateUtility_NV_G4 (I have a g4 device) to upgrade hardspl. I got message that my update utility was old and that I need new. Then I restarted device,just run ROMUpdateUtility_NV_G4 from the hardspl folder and instalation went smooth,pda restarted and worked well. Then I went back on xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide,found this sentence: ''Step 3 and 4 are necessary only if the WM6 rom you have downloaded instead of nk.nbf has os.nb file and the ExtROM folder'', and as I downloaded wm61_korand_3_1.rar that contains only nk.nbf file,I put it in Update_Package\Update Utilities,and run ROMUpdateUtility_NV_G4 fron that folder. The instalation finished and pda booted in bootloader. After that I tried flashing Shadow My Edition 2,no DualSIM,and followed the instructions to recover pda from wiki/ prophet recovery(downloaded PDAMobiz_Prophet_WM6_V1.00_Step1),everything was the same,always bootloader. Is there a help for my prophet? Could someone give me a step by step istruction how to bring it to life? Any help is welcome. Thanks
What is the IPL/SPL displayed?
Are you sure your device is a G4?
Try a hard reset.
Try this again: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
IPL 2.58.0001
SPL 2.58.0001
I'm sure that my device is g4. Did a hard reset and it went to bootloader again. Is there a hope? I will try http://wiki.xda-developers.com/index...ophet_recovery, but I noticed that when I run RUU and after verificatio informations on my pda it shows image version :_____________(blank),,then I click update,and then it shows
From:
image version :
To:
image version :
there is no numbers.
If you can enter bootloader, the device is recoverable.
HardSPL???
nikolah said:
I was trying to make upgrade from wm5 to wm6,and was looking in tutorial xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide. First,I found a Upgrade_HardSPL_G4.rar, and did what was said in tutorial,copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,Execute the SPL.lnk IN THE DEVICE, then you see Prophet in all bright or white screen,Execute the ROMUpdateUtility_NV_G4 (I have a g4 device) to upgrade hardspl. I got message that my update utility was old and that I need new. Then I restarted device,just run ROMUpdateUtility_NV_G4 from the hardspl folder and instalation went smooth,pda restarted and worked well. Then I went back on xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide,found this sentence: ''Step 3 and 4 are necessary only if the WM6 rom you have downloaded instead of nk.nbf has os.nb file and the ExtROM folder'', and as I downloaded wm61_korand_3_1.rar that contains only nk.nbf file,I put it in Update_Package\Update Utilities,and run ROMUpdateUtility_NV_G4 fron that folder. The instalation finished and pda booted in bootloader. After that I tried flashing Shadow My Edition 2,no DualSIM,and followed the instructions to recover pda from wiki/ prophet recovery(downloaded PDAMobiz_Prophet_WM6_V1.00_Step1),everything was the same,always bootloader. Is there a help for my prophet? Could someone give me a step by step istruction how to bring it to life? Any help is welcome. Thanks
Click to expand...
Click to collapse
would you mind to read me thread?
dioxda2,I read your thread. and I will now try a other hardspl that you linked there. Was that the remark you wanted me to come to my notice?
Same Issue
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
georgexavier said:
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
Click to expand...
Click to collapse
there are sucessful cases , please read my post or.... are you using Vista?
If so, you need other solution. (not with me ... sorry ~~ )
georgexavier said:
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
Click to expand...
Click to collapse
What is the SPL of your device?
When recovering to WM5 you better NOT use the Mobis step 1. Any other step 1 or NVID will be fine. The Mobis ROM is too manipulated for flashing their own WM6 ROM. It will give all kinds of problems when it is used for other purposes.
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
nikolah said:
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
Click to expand...
Click to collapse
see my thread la~~~~
dioxda2,I have read your thread. This is what I know at the moment,and what I think it should be done (correct me if I make any mistake):
-my pda boots in bootloader mode
-it shows on screen IPL:2.58.0001, SPL:2.58.0001
-it's G4 model
-it has no hardspl on it
First one wild shot:
1. Download this jumpspl http://forum.xda-developers.com/showthread.php?t=329147
2.follow the instructions,and instead nk.nbf file from desired rom I put a nk.nbf file found in hardspl rar archive to the SoftSPL folder ,and hopefully flash hrdspl.
3.from bootloader flash any desired wm6 rom with RUU
Second solution:
1.download PVTemp
2.try to flash it from bootloader
3.if it's ok,then on to the next step like on your page one for old method.
Is there something else,diferent way to do this from bootloader?
Thanks for all help
In bootloader, try to flash this: ftp://xda:[email protected]/RUU_Prophet_220734_2207114_024721_NVID.exe
nikolah said:
dioxda2,I have read your thread. This is what I know at the moment,and what I think it should be done (correct me if I make any mistake):
-my pda boots in bootloader mode
-it shows on screen IPL:2.58.0001, SPL:2.58.0001
-it's G4 model
-it has no hardspl on it
First one wild shot:
1. Download this jumpspl http://forum.xda-developers.com/showthread.php?t=329147
2.follow the instructions,and instead nk.nbf file from desired rom I put a nk.nbf file found in hardspl rar archive to the SoftSPL folder ,and hopefully flash hrdspl.
3.from bootloader flash any desired wm6 rom with RUU
Second solution:
1.download PVTemp
2.try to flash it from bootloader
3.if it's ok,then on to the next step like on your page one for old method.
Is there something else,diferent way to do this from bootloader?
Thanks for all help
Click to expand...
Click to collapse
Hi there ~~~~ tell you what~~ ^_^
1. there are 2 ways to upgrade
a. " New " Method.
b. " Old" method.
2. for more update rom flashing.... better have you device hardSPL.
then you can go by 3 means to flash....
1. straight upgrade that is: connect to PC via activesync, activate RUU right ahead ( I don't like this method as sometimes will stuck @ bootloader,
2. copy the 3 files from the jumpspl to the prophet's root directory then activate manually...
3. force bootloader ( by manually buttons combination and not reboot in 3 color hang )...
then 2 and 3 is fine, ( 3 is more convenience though), you should see " USB " at the bottom prophet screen if you did things right. ^_^,
then flash...... ^_^
This is my [size=+2]little handmade tool [/size], a combination tool with Taiwan Cook - YouZii and XDA cook - Korand,
just unzip, execute the " UPGRADE.cmd " , the some on screen clicks, wait and done. !!!
Don't forget to hardSPL before so. OK?
Enjoy ~~~
A Batch flashing tool and Korands clean rom 3.1... Check it out ! ^_^
P.S. Connection Error? Please try again ~~ ^_^
nikolah said:
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
Click to expand...
Click to collapse
You will find it here:
ftp://ftp.xda-developers.com/Uploads/Prophet/Prophet-roms/
So, after first succesefull flash of my tytn I took friends mda vario 2 to do the same. And bricked it!!!
Because of first unsuccesefull flash when I downloaded RUU_inside.nbh file into HardSPL7 directory. So, I connected vario and started RUU_wrapper. BUT in a next few seconds I realised that I am upgrading ROM instead of HARDSPL-ing File inside was from DopodAsia WWE.
Upgrade stared, in a 30minutes it stucked in 24% and I disoconnected PDA. After that it stucked in bootloader! SPL 2.03!
I tried to do HardSPL after-no help. I tried to install ATT Stripped ROM- error on 1%. I downloaded official WM 5.0 GER - no help again.
Few more attempts of flashing HARDSPL, and ROM-s via RUU-wrapper didnt help eather. THEN JUST SOFTRESET: I saw dopod bootsplash screen, and windows started normally!!! I couldnt believe, because I was prepparing to do that complicated procedure of unbricking.
After starting windows I just did HARDSPL and ATT stripped ROM: All OK UNLESS GSM!
Is it possible to fix??
To +Que PPC and boog321: thanks to earlier advices!
OK! I flashed RADIO ROM 1.56.70- IT WORKS!
Guys who are making this software are fenomennal
hahaha!!!!! Nice experince man!!!
Well i think we all has to thank to Olipro! POF! and many old XDA members that makes this posible!!!
Keep it up.... and for the enxt device please... read eveything two or three times! hahaha and please don overwrite files... its better to make new folders!
Keep it up!
haha, thanks Que...
I was in a hurry, so I just connected PDA and start wrapper. I shocked when a I saw wrong .nbh file, but it was too late. But luckely it looks like new ROM was partly OK and I was able to start WM, then flash HardSPL and WM correctly.
Both hermes are working fine.
P.S. I would like someone to put simple guide for people who only want to change their ROM to simple WWE, and have some experience.
1. Download HardSPL7 and unzip to folder on PC
2. Download ATT ROM and unzip to different folder on PC
3. Connect via ActiveSync
4. Start RUU wrapper from HardSPL folder and follow instructions
5. See if you flashed correctely (in a bootloader must be 2.10.01olipro in SPL)
6. If its OK than reset, start WM on PC, connect via ASync and start RUU-wrapper FROM ATT ROM folder, choose autodetect or SPL you have seen in bootloader screen - accept everything....Wait for 10min and enjoy in ENG ROM!
Thanks Oli, Pof and all others of course!