Related
Hi, looking for advice on how to fix if possible a M3100 with failed phone functions. Started when 3G went down in area, swithced to GSM worked for a while then lost signal completely, tried hard reset to fix but during setup i tried to set a pin for the phone element of the device as prompted to do so, on re boot the pin screen showed but neither touch screen or keyboard would allow me to enter it so i re- booted and same thing happened a number of times. Tried hard re set and device works except phone, no signal and doesnt recognise sim as present, cannot enter phone menu through any route. My sim works perfectly in my old phone. Is this hardware or software, phone functions failed before hard re set? would un locking fix this or does it need to go back to HTC?
Any advice appreciated
What do you see in the boot screen when soft-reseting?
You should see in red letters your radio version next to an "R" in the bottom-right part of the screen.
On boot up i see the following in red at the bottom of the screen:
M05
S04
B05
D 1.23
NO GSM
"NO GSM" shows that radio rom is probably screwed.
Go into bootloader and run the commands "rtask 1" and "rtask 0" in mtty. This will try to turn on the radio and reset it.
Also see the output of commands "checkimage" (should give you a radio image CRC checksum) and "info 8" to see that your flash is intact.
If the process above does not fix the problem you should better go for a replacement with Orange... or if it is not possible wait until they release a ROM upgrade and see if it fixes the problem.
Do not flash any other rom if you pretend to return the unit.
Info 8 shows all blocks reversed
rtask 1 has no effect
Check image shows results for all except radio image crc showing wait interpreter time out
The unit is an e-bay special so cannot return it, wil flashing rom with non ornage version fix this problem? or must it be orange to work properly with network services?
Thanks
I don't know if flashing would fix it, but if you have no warranty then go for it. It doesn't need to be an Orange rom, you'll get the Vender ID error if the flashed rom doesn't match your CID, but just follow the instructions on the wiki...
LC said:
The unit is an e-bay special so cannot return it, wil flashing rom with non ornage version fix this problem? or must it be orange to work properly with network services?
Thanks
Click to expand...
Click to collapse
Au contraire, book it in at
http://service.htceurope.com/
it is based on seriel number you don't need no stinkin' paperwork....
I have bought from eBay and sent back under warranty many times ;-)
Just don't flash a dopod rom on there just yet as then they'll know...
Richard
Thanks for the help and advice, will send it to HTC
LC said:
Thanks for the help and advice, will send it to HTC
Click to expand...
Click to collapse
If you do end up being charged for a 'bad flash' etc the most it will cost you is about £30. Better than a non-working device.
Richard
i unlock G4 Wizard with this method. and after i flash it with a turkish rom file. it's success and very well working without sim card.
Bu when i insert a sim to wizard, it has locked the ppc. and after i flash it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.
and after the ppc is open but stuck on opening screen. i try to master reset it but i can't. and after i remove the battery and detach the sim.
now the ppc can't open. i try to get it to bootloader mode but i can't. when i press master reset & camera button, nothing happens.
i try different button combinations but it can't open.
edit:
i flash it with RUU MUN program
please help
Oh my god...
Flashing Hard SPL to your device does not mean you can flash any ROM you want. You can only flash ROMs that doesn't have IPL and SPL.
Since CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE (Button's ROM) includes IPL and SPL 1.01, you most likely bricked your device.
in this case what can i do?
can i change the flash of the phone? if yes, hoc much does it?
Help Me I Did The Same
I Have The Same Problem If Theres A Solution Please Help Me!!!...
AYALA445 said:
I Have The Same Problem If Theres A Solution Please Help Me!!!...
Click to expand...
Click to collapse
Alas!
If there cud be a solution,but sorry,its a 'BRICK'.There's no solution except to sell it as parts.
If you are in China, there are places that can replace the flash chip for you. Outside China, there seems nobody do this kind of repair...
Hi
Iam new to this site.
I had downloded HTC_Hermes_SIM_CID_Unlock_v3a and installed AUTO_Unlock_v3a. Now iam able to use new SIM.
But after puting a new SIM withing 10 seconds USIM message is coming. Friends kindly tell me how slove it.
HERM200
IPL-SSPL by Des
SPL-1.09.ds
Expecting your kind advice
sati
cnsathya said:
Hi
Iam new to this site.
I had downloded HTC_Hermes_SIM_CID_Unlock_v3a and installed AUTO_Unlock_v3a. Now iam able to use new SIM.
But after puting a new SIM withing 10 seconds USIM message is coming. Friends kindly tell me how slove it.
HERM200
IPL-SSPL by Des
SPL-1.09.ds
Expecting your kind advice
sati
Click to expand...
Click to collapse
Unfortunatly the Softbank hermes cannot be unlocked after a certain point:
pof said:
..It can be used in all HTC Hermes devices, no matter which bootloader version the device is running.
NOTE: For x01ht post April devices, see this thread....
Click to expand...
Click to collapse
pof said:
...This process is ONLY valid for new devices which have never turned on or let the SoftBank Extended ROM install.
If you have already let the ExtROM install you CAN'T sim-unlock it.
Click to expand...
Click to collapse
sounds like you have let the device install the ext_rom when you first turned it on, unfortunatly you cannot unlock it to use any sim card.
But you can do it with IMEI Check, you just cannot change radio version afterwards, but on newer version of X01HT it's 1.46 radio, so it's quite ok I think.
mrvanx said:
Unfortunatly the Softbank hermes cannot be unlocked after a certain point:
sounds like you have let the device install the ext_rom when you first turned it on, unfortunatly you cannot unlock it to use any sim card.
Click to expand...
Click to collapse
So if i upgrade to the latest radio rom,it still can't be solved??
how about if we change the EXtRom?
Success
My job done.
I have flash n unlock it.
With this JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship.exe
see this link http://forum.xda-developers.com/showthread.php?t=281617&page=24&highlight=X01HT+rom+english+version
but make my cooking rom.(maybe u can say i just choice some part from the other rom)
i use NBHtool to make my own
1.extract JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship.exe and HTC_Hermes_SIM_CID_Unlock_v3a (winrar)
2.decompile nbh file (HERMIMG_CDL_1.31.305.2_SHIP.nbh) and (HermesUnlocker_v3a.nbh)
3.Compile again but
IPL.nb; SPL.nd and RAdio rom use extracted from HermesUnlocker_v3a.nbh
4. PrimarySplash.nb ; SecondarySplash.nb ; windows(OS) i take the orginal JASJAM rom
5.ExtRom i take from extracted from the orginal rom (RUU_X01HT_1.33.761.4_1.14.00.10) ----> and this is my mistake.
I test with ExtRom from JASJAM ----> it work.great!
So i just take all except IPL.nb ; SPL.nb and Radio rom ---> extract from HermesUnlocker_v3a.nbh
After that the Compile file copy to folder that u extract JASJAM rom but delete the HERMIMG_CDL_1.31.305.2_SHIP.nbh file.
5.conect your softbank.
copy SSPL-HERM.exe to your Softbank then run it(from your PDA off course)
note : If screen USIM show always just reset it,after desktop show up,in 10 sec before USIM screen,open explorer then run it.
U'll see 3 color background (i think u know it)
6.flash it.
7.Just follow the instruction,but when it ask to choice an operator region,i just cancel it.(i did'nt tried if i choice it.i think i dont need it)
After that enjoy it.
but the problem is u cant use 3G
see the other thread to solve it.
hi... Learning.....
may i ask what ur x01ht was?
is it before april or post april?
I have this message coming up on a Japanese language version X01HT. I don't think it's been unlocked. Will these instructions work on my phone?
EDIT: I followed the instructions above on my phone, and they worked perfect!!! Thanks!
how can I tell if my phone is "post april"?
USIM Message GONE!!!!
Hello cnsathya,
Not sure if you still have the problem. I just got my x01ht Hermes yesterday and I worked on it today to unlock it. I used pof's (THANK YOU SOOOO MUCH) unlocker v3 but still USIM showed then later put my t-mobile sim and re-ran the unlock software but after 10 sec I still got the USIM message. I moved SB_USIM.cab to the phone and ran it before the USIM message came but nothing seemed to change. But I could then use my sim and receive calls so I flashed the PIMPING IS BACK v3 ROM by jasjammin and it now works perfectly and no more USIM. I had an old x01ht but cracked the screen so bought this one. Let me know if you need more information or have questions. Thank You,
Pr4tik
learnig said:
My job done.
I have flash n unlock it.
With this JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship.exe
see this link http://forum.xda-developers.com/showthread.php?t=281617&page=24&highlight=X01HT+rom+english+version
but make my cooking rom.(maybe u can say i just choice some part from the other rom)
i use NBHtool to make my own
1.extract JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship.exe and HTC_Hermes_SIM_CID_Unlock_v3a (winrar)
2.decompile nbh file (HERMIMG_CDL_1.31.305.2_SHIP.nbh) and (HermesUnlocker_v3a.nbh)
3.Compile again but
IPL.nb; SPL.nd and RAdio rom use extracted from HermesUnlocker_v3a.nbh
4. PrimarySplash.nb ; SecondarySplash.nb ; windows(OS) i take the orginal JASJAM rom
5.ExtRom i take from extracted from the orginal rom (RUU_X01HT_1.33.761.4_1.14.00.10) ----> and this is my mistake.
I test with ExtRom from JASJAM ----> it work.great!
So i just take all except IPL.nb ; SPL.nb and Radio rom ---> extract from HermesUnlocker_v3a.nbh
After that the Compile file copy to folder that u extract JASJAM rom but delete the HERMIMG_CDL_1.31.305.2_SHIP.nbh file.
5.conect your softbank.
copy SSPL-HERM.exe to your Softbank then run it(from your PDA off course)
note : If screen USIM show always just reset it,after desktop show up,in 10 sec before USIM screen,open explorer then run it.
U'll see 3 color background (i think u know it)
6.flash it.
7.Just follow the instruction,but when it ask to choice an operator region,i just cancel it.(i did'nt tried if i choice it.i think i dont need it)
After that enjoy it.
but the problem is u cant use 3G
see the other thread to solve it.
Click to expand...
Click to collapse
JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship .exe <<< the page can not be found... does anyone help to upload please...
Is it ?
http://rapidshare.com/files/17336753/JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship.exe
It was listed here http://mobi.pdafans.com/viewthread.php?tid=275408&extra=page=3&filter=type&typeid=178
bayupraya said:
JASJAM_wwe_1.31.305.2_1.31.305.104_1.21.31.10_ship .exe <<< the page can not be found... does anyone help to upload please...
Click to expand...
Click to collapse
This is a very old thread and I beg your pardon for bumping it, but I am looking for a thread which can help me solve my problem for like 15 hours now and this is the closest answer I got. My issue is similar to this, only mine is X05ht or the Touch Pro device. Similar Softbank carrier and yes similar USIM message issue.
Anyone can help me point to the right direction of solving my issue like the threadmaker solved hers/his on this thread? Please?
HTC xo1ht
Iam new to this site.
I had downloded HTC_Hermes_SIM_CID_Unlock_v3a and installed AUTO_Unlock_v3a. Now iam able to use new SIM.
But after puting a new SIM withing 10 seconds USIM message is coming. Friends kindly tell me how slove it.
got a niki200, what was flashed badly by someone, and he said, the flash was stopped at 9x%... now the device swithes on only at bootloader scree, what is:
------------------------
NIKI200
SPL-1.21.0000
CPLD-4
Upgrade ROM code error
Please try again
------------------------
I can't upgrade with any RUU, all of them stops at 0% and reports that device needs recovery.... after recovery steps, problem still persist.
If I use "factory" RUU with any carriers rom RUU reports bad vendor ID after 1% (I think it's becouse the person who tried to flash before me doesn't made CID unlock first).
Anyone knows how to repair this problem? Device was originally TMO-HU branded.
Thanx
used mtty to send command "boot", command runs, but device remains in bootloader screen... anyone can help me?
maybe device is German TMO branded originally, not TMO-HU one
after talking to the person, who has bricked the device, it turns out, that he forgot to hardspl the bootloader, so now the original 1.21.0000 is still in the device, and he has flashed with some pathed radio rom for supercid unlocking (without hardspl first)... is there any way to flash back some working radio rom and unbrick it? Device doesn't accept radio rom flashing , but I will try with all the available versions, maybe some of them will work...
gyuszko - you phone is locked, so the only way - flash original rom.
For example. My niki have come from Thailand, but i use it in China. Once, i have bricked it, and the only way that have helped me - flashing original Thailand rom
(It works fine on unbranded phones, but i think branded can be unbricked by same way )
thanx for your answer, I searched a lot, but haven't forund original rom for it... even registered at htc-club and entered device's serial, but no luck, no sw update for this device
What is original sn of you rom?
There is one branded (SignTel) rom:
ROM version: 1.31.871.14
ROM date: 11/29//07
Radio version: 1.58.16.27
Protocol version: 25.61.30.03H
P.S. Did you ask TMO-HU about it?
s/n: HT818Gxxxxxx
yes, TMO-HU branded
I mean what version of rom is yours original, not sn of device
And did you ask operators service for rom?
I don't know the original version, 'coz someone else bricked the device...
Try this one http://rapidshare.com/files/1522292...14_Radio_Nike_1.58.16.27_signed_Ship.zip.html
It's not T-mobile, but is branded WWE
hi gyuszko,
if understud, we have the same problem.
surfing on this forum, i've read it:
Elf SD Card flashing
This page describes how to upgrade your Elf ROM using an SD Card. This is useful for:
Linux and Mac users: you don't need windows to upgrade the ROM
ELF0IMG.nbh on a FAT32 filesystem
Empty (erase the contents) of your microSD card from the Windows Mobile file explorer or format it from your computer using a card reader (in some cases format doesn't work).
Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
Rename the .NBH file to ELF0IMG.nbh and copy it to the root folder of your microSD card.
With microSD card inserted on the phone, start the bootloader (The bootloader is invoked by hold down the camera button and reset device with the stylus).
confirm flashing on screen by pressing the power button (or the volume slider down).
Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
SuperCID devices are able to flash any NBH image using this method.
Click to expand...
Click to collapse
now, i've try on my touch dual (niki100), bat i don't know how i mast to nomine the rom file for our smartphone....
have you any idea?
Festermax.
Szia!
Lesz megoldásom 1-2nap múlva :-d
Írok majd
sőt adok linket
red6 said:
Szia!
Lesz megoldásom 1-2nap múlva :-d
Írok majd
sőt adok linket
Click to expand...
Click to collapse
SZia,
engem is érdekelne, mert próbálkoztam update-lni, de...error van.
Szia! H!
Sok sikert!
http://rapidshare.com/files/272691817/NikiT07.rar.html
Niki200
T-mobile HU
Original Rom
http://rapidshare.com/files/272691817/NikiT07.rar.html
Tutti hogy Niki 200-on nem megy a Niki100-as törés!
De ezzel legalább vissza lehet állítani!
Ha valakinek van valami megoldása a Niki 20-hoz, az írjon.
This supercid crack wont run on the Niki 200, but it will only run on the Niki 100.
But its a sure thing to recover it.
If anyone has any solution for the Niki 200 supoercid crack, please om me.
Hi.
I tried to find this on the forum and wiki, but i couldn't, so i want to ask.
I got a used Softbank X01HT, and seller said it was unlocked, but when i put in my sim i can do things for about 30 seconds, and then there comes a U-SIM screen and it asks me to enter something, i guess ( It's in japanese ).
How can i get this to go away? Is it even unlocked?
ROM: 1.33.761.4
Radio: 1.16.00.00
When i make call to phone i does to through and people can all even though U-SIM screen is there, and when people call, it is possible to go to the menues and such.. But when they hang up it goes back to U-SIM screen.
Please help
I have already read the Post april X01HT thread, though it is not relevant in this case because this is model from 2006.
Thank you
this is SIM unlocked phone (radio version 1.16.00), but your Windows Mobile ROM is the original SoftBank Japanese version that enforces USIM message...
You can flash to some other Windows Mobile ROM, but make sure you check Hard-SPL thread first (sticky in Hermes upgrading etc)
Hi thank you again!
I read something like that in the SIM unlock thread.
So i just need to install Hard-SPL and then flash a ROM?
Do i also need to do CID unlock? (http://forum.xda-developers.com/showthread.php?t=293665)
I would like to be able to write japanese with the phone, so is that possible if i flash? I saw a thread about installing japanese input/output support, is that possible to install on every rom?
And can you reccomend a rom or post link to ROM you think i should install?
THANK YOU! can't wait to start using it.
Now i just tried the Hard-SPL thing. But i get Update error 260 saying my device is not connected. I have ActiveSync 4.5 open and i have synced..
so i don't know.
I don't know if it has anything to do with the USIM screen being on all the time?
I see Active sync closing down as soon as it starts updating.. but then it can't update, right?
easiest way is to use SoftBank SIM for flashing everything, that way you avoid USIM message...
if you dont have SoftBank SIM available, search for welcome.exe on this forum.
SoftBank put a software SimLock in the ROM which can be removed with welcome.exe from imei-check unlocker. (http://www.imei-check.co.uk/m3100unlock.php) Start it up with you phone connected to USB and ActiveSync enabled... After the program asks for some password file, just close it! (close dos prompt window)
About Japanese IME (kanji & kanna input), i prefer flashing some newer English WM6 ROM + installing separate Japanese IME from cab. Old SoftBank's ROM is very slow and limited...
Super CID is just there if you flash HardSPL....
HI, thank you!
I found out that the USIM screen goes away if you just press on the signal bar and say that you don't want to receive signal.. den i can ue it.. And then i could do the Hard-SPL which i did with no problem. thank you!
Ah so if i just download that program and close it down at that time the USIM screen with never come again?
Yea i want to flash it to newer. But i'm not sure which one because i've heard a lot of people broken their phone :/
could to give me a link to a few "good" English WM6 ones?, though i there is probablt many.
i will try out the imei-check thing now ^_^!
Once you flash HardSPL; when you want to flash only Windows Mobile ROM only you dont have to worry about bricking (destroying) your phone. Only flashing different radio could be dangerous.
For the version, you have to find out yourself, there are so many... Check Hermes Mobile 6 threads, there are even some special Japanese cooked ROMs if i remember correctly. Also check user signatures for what versions are different people using...
thanks so much! i managed to get the USIM screen gone with your help.
Ahh i see, but install new version wont it also change the radio? wasn't that dangerous?(sorry if i ask dumb question)
so if i chose this for example: http://forum.xda-developers.com/showthread.php?t=359458 i can still make it with Japanese IME?
i think i will try hehe!
that link you provided is Schap's WM6 Pro 4.31 ROM... It is one of the most stable out in the wild, and it comes without radio, so flashing that one should be safe.
Oh ok thank you! then i will try this.
Last question before i do anything
This that ROM it is still possible to do the Japanese IME thing?
I found this thread
http://forum.xda-developers.com/showthread.php?t=298919
It explains something of getting japanese on phone, was this what you meant by japanese IME? or is there an other method, if yes, please telle me/ give link.
Now time to have your Hermes speak Japanese
Japanese fonts
Use the excellent work from Asukal, that you can find here:
http://www.asukal.jp/WM5/LetsJapanNo5.zip
I did have a problem with it: once I executed it, I could not sync with my Exchange server (Quite a pain for my push email account...)
Asukal found the solution: edit the registry, and change
[HKEY_LOCAL_MACHINE\Software\Mobem\CE-Star] "MyNLS" = "\windows\wince.nls"
Japanese input
Not using for myself, but these work perfectly (I tried):
http://www.asukal.jp/WM5/BagojsINPUT.zip
*** EDIT
If you prefer a Japanese input without the annoying "Floating bar", ie just the same input way as your original WM5 Softbank ROM, just downlaod and install the "MS IME31 J" link from Asukal's page:
http://hn801.hkes.com/Data/SIP/IME_31J_QVGA_F.zip
Click to expand...
Click to collapse
THANK YOU!
That solution you mention should work fine, but newer solution is available. Check http://forum.xda-developers.com/showthread.php?t=445550
Hi! THank you very much! i was finally able to flash the ROM!!
And i have installed the Japanese fonts and Input thing!
It works. but after install i can not sign onto MSN Live Messenger. Is there anyway to fix this problem?Maybe i should change something in Regedit?? Or should i uninstall the fonts again? :/
It gives me this message: There's a Connectivity problem. Make sure you're in an area with good reception and try again.
I have tried over and over and WIFI is up and working..
So any answer i would be so greatful and finally be able to use the phone like i dreamed of !
Thank you.
sorry, i dont use msn, i have no clue about it...
明けましておめでとう。
Ok thank you anyway!!
明けましておめでとう〜
良い年でありますように♪o(^-^)o