Tired of the lack of possibility to turn off 'automatic light sensor', I have modified the original driver. The only difference is - I removed code that enables ALS.
Issues:
- sometimes screen wake ups with maximum backlight value and fades to desired value in seconds.
Manual installation:
- push ax8noals.ko to /system/lib/modules
- run the following command
Code:
insmod /system/lib/modules/ax8noals.ko
- set desired brightness.
Until you're sure that it works with your hardware, don't install it to hw_config.sh.
Make sure that module is inserted before lm3530 LMU configuration settings.
Code:
#insert new noALS module
insmod /system/lib/modules/ax8noals.ko
sleep 2
# lm3530 LMU configuration
dev=/sys/devices/platform/i2c-adapter/i2c-0/0-0036
echo als_off > $dev/mode # add this line if system overrides your mode
Release history
v002:
- restored how original modes works:
- i2c, pwm, i2c_pwm: modes without als,
- als, pwm_als, i2c_pwm_als, i2_als: modes with als- added two new modes:
- als_off - disables als in ALS enabled modes,
- auto - enables als in ALS enabled modes.
v001: just recompiled original driver with ALS disabled
Note:
It uses code to remove original driver from doixanh X8Gesture module.
Disclaimer
I'm not responsible if this module damages your lovely phone. Use it at your own risk!
thanks i guess i will need that one someday....
nice work dude...
Another moduler,ok then please,please,please make overvolt module for x8
as-mario said:
Another moduler,ok then please,please,please make overvolt module for x8
Click to expand...
Click to collapse
You wanna fry your phone? XD
Sent from my X8 using Tapatalk
as-mario said:
Another moduler,ok then please,please,please make overvolt module for x8
Click to expand...
Click to collapse
I guess this is not even possible with the current kernel cause Dx would have done that long ago!
Sent from my X8 using XDA Premium App
No one has managed to overvolt MSM7227 yet, I've googled about that already. So I doubt it's the kernel problem.
Blagus said:
No one has managed to overvolt MSM7227 yet, I've googled about that already. So I doubt it's the kernel problem.
Click to expand...
Click to collapse
Wat could be the proplem then?
Sent from my X8 using XDA Premium App
What could be the advantages and disadvantages of Overvolt and Undervolt in our Xperia X8.....I really don't understand what could be used for, please inform me.
as-mario said:
Another moduler,ok then please,please,please make overvolt module for x8
Click to expand...
Click to collapse
Why don't you make it yourself?
Please someone, tell me what could be the advantages and disadvantages of Overvolt and Undervolt, and what could be used for? Please inform me.
Koulis2000 said:
Please someone, tell me what could be the advantages and disadvantages of Overvolt and Undervolt, and what could be used for? Please inform me.
Click to expand...
Click to collapse
Overvolt can be used to make the phone more stabile at higher frequenses so if we whould have overvolt we whould probobly be able to overclock to 800MHz or more stabile. Undervolt can be used to save power and improve the battery.
Sent from my X8 using XDA Premium App
ponanovn said:
Overvolt can be used to make the phone more stabile at higher frequenses so if we whould have overvolt we whould probobly be able to overclock to 800MHz or more stabile. Undervolt can be used to save power and improve the battery.
Sent from my X8 using XDA Premium App
Click to expand...
Click to collapse
But Overvolt will increase the Temperature of the phone at crazy rate am I right?
Koulis2000 said:
But Overvolt will increase the Temperature of the phone at crazy rate am I right?
Click to expand...
Click to collapse
Not that crazy I guess
Sent from my X8 using XDA Premium App
Koulis2000 said:
But Overvolt will increase the Temperature of the phone at crazy rate am I right?
Click to expand...
Click to collapse
That depends on how much you overvolt, your phone can get overheated without overvolt also but it is easier to overheat it with overvolt.
EDIT: Off topic, sorry.
Sent from my X8 using XDA Premium App
skyboyextreme said:
Not that crazy I guess
Sent from my X8 using XDA Premium App
Click to expand...
Click to collapse
My standard OC is at 748 and when I set it at 76something it starting getting hot, guess that in 800 it will spraying flames from the 3.5 jack plug.
Koulis2000 said:
My standard OC is at 748 and when I set it at 76something it starting getting hot, guess that in 800 it will spraying flames from the 3.5 jack plug.
Click to expand...
Click to collapse
You are wrong, my friend can set his phone to max 826mhz without reboots or FLAMES!
this is not overvolt module thread. please respect the OP.
offence guys, what is the disadvantage with auto light sensor that you want to disable? @[email protected]
i hope you post it around feb when I want to throw to garbage my x8 coz of crazy brightness even though i turn it off. Now theres no problem with custom roms
Related
Should the Dalvik Just in Time compiler be activated or deactivated? I'm suing MiniCM Released by NobodyatAll. Some say it's better to have it off than on, but I dunno.
I have it on, everything works like a charm... just try both, and if you don't see any diffrence, toss a coin ;D
Sent from my X10mini using XDA Premium App
Quadrant score difference is approx +- 100
E.g quadrant with JIT on 987 .... quadrant with JIT off 1110
Sent from my X10mini using XDA App
what is exactly the function of JIT?
epaljr said:
what is exactly the function of JIT?
Click to expand...
Click to collapse
It's a Dalvik Just in Time Compiler.
http://en.wikipedia.org/wiki/Just-in-time_compilation
It boosts the runtime performance, something something.
its better with jit off.... you also save a lot of battery
how do u turn it on/off ?
eladmagen said:
how do u turn it on/off ?
Click to expand...
Click to collapse
go to settings>cryanogenmod settings>performance settings>UNCHECK the box against JIT!
shougo93 said:
its better with jit off.... you also save a lot of battery
Click to expand...
Click to collapse
But why do come up JIT ... May simply not have enough memory and can be decrease dalvik.vm.heapsize = 24. When i do not root phone test this moment, with 24M work best.
I am using gingercruzt 1.3 (I use the P500) and I saw some very good characteristics of this rom:
1. Do tweak more scrip than the other rom.
2. Options undervolt your computing power to work well with the best.
3. Option "use 16 bit transparency" to help smooth over but the picture may change significantly.
So why not use this to apply to the other rom, this is fairly or that.
khoa02061986 said:
I am using gingercruzt 1.3 (I use the P500) and I saw some very good characteristics of this rom:
1. Do tweak more scrip than the other rom.
2. Options undervolt your computing power to work well with the best.
3. Option "use 16 bit transparency" to help smooth over but the picture may change significantly.
So why not use this to apply to the other rom, this is fairly or that.
Click to expand...
Click to collapse
You can't undervolt a MSM7x27 chipset...
terratrix said:
You can't undervolt a MSM7x27 chipset...
Click to expand...
Click to collapse
But the custom of Ginger Cruzt is that you, in setting, gingercruzt setting, performance.
khoa02061986 said:
But the custom of Ginger Cruzt is that you, in setting, gingercruzt setting, performance.
Click to expand...
Click to collapse
No, that do not work actually, it only works with xperia x8, as this is a xperia x8 port over, so its just aesthetics. Any undervolting in our device is impossible.
terratrix said:
No, that do not work actually, it only works with xperia x8, as this is a xperia x8 port over, so its just aesthetics. Any undervolting in our device is impossible.
Click to expand...
Click to collapse
But x8 also has a msm7227 chipset,then how does it work there??
ashishv said:
But x8 also has a msm7227 chipset,then how does it work there??
Click to expand...
Click to collapse
I think it's because P500 have a different voltage set and kernel than in xperia x8
boykioy not so nice where you can have a certain utility, when you stick with that option, the machine is less clear energy
terratrix said:
I think it's because P500 have a different voltage set and kernel than in xperia x8
Click to expand...
Click to collapse
So if someone is able to make an undervolt kernel,it might work on our phone,right?
ashishv said:
So if someone is able to make an undervolt kernel,it might work on our phone,right?
Click to expand...
Click to collapse
well, if you can apply to every rom, it will open an "era" less energy to P500 android particular and general. kekekeke
As i saw in xperia x8 forum, undervolt didn't have a great effect on battery, and undervolting in our phones(eventhough impossilble) will affect stability even at 600MHZ
terratrix said:
As i saw in xperia x8 forum, undervolt didn't have a great effect on battery, and undervolting in our phones(eventhough impossilble) will affect stability even at 600MHZ
Click to expand...
Click to collapse
how to test the "stability" it? Check with any energy?
Besides, do you think about custom "use 16 bit transparency" ?
khoa02061986 said:
Besides, do you think about custom "use 16 bit transparency" ?
Click to expand...
Click to collapse
Well, it works, because i think Optimus One does not support 32bit framebuffer...
---------- Post added at 05:04 PM ---------- Previous post was at 05:04 PM ----------
khoa02061986 said:
how to test the "stability" it? Check with any energy?
Click to expand...
Click to collapse
Stability as in your won't get any random reboots, kernel panic etc
I find the immediate use gingercrust 1.3 quite well, wait a while longer to see the problem on that something was wrong, then I will change rom
Our kernel does noot support undervolt, the settings are there in the rom but it is not supported.
Other than that, it has many many tweaks, and as a resulkt the scrolling is smoother that any available rom and the responce is very very good.
Thanks
Sent from my LG-P500 using xda premium
i have a problem don't know if it's related to my custom kernel i use inteks v15 , my neo some times randomly sets it's cpu maximum frequancy to as little as 122mhz only !!
max freq = 122mhz
min freq = 122mhz
and it happens randomly i mean RANDOM !! the device just becomes so laggy even the simplest stuff become laggy and i have to reset the maximum allowed cpu frequancy again to 1401mhz using sexperia to make the device act normal again !
hope some one can clear this up for me......
which kernel you use?
electrash said:
which kernel you use?
Click to expand...
Click to collapse
inteks v15 i first noticed this after installing launcher pro but i doubt it has anything to do with this cpu throttling problem
try to unistal that app :/
Maybe you are using 2 similiar cpu frequency changing app.
Uninstall all cpu apps and clear data all those apps.
Sent via my FXP 046 MT15i®
taaviu said:
Maybe you are using 2 similiar cpu frequency changing app.
Uninstall all cpu apps and clear data all those apps.
Sent via my FXP 046 MT15i®
Click to expand...
Click to collapse
Same here, but I think that taaviu is right. I have ROM Toolbox and CPU Tuner installed, both can set the cpu.
sdk16420 said:
Same here, but I think that taaviu is right. I have ROM Toolbox and CPU Tuner installed, both can set the cpu.
Click to expand...
Click to collapse
That's my point.
I use cm7..there is built-in already cpu setting and when I use setcpu and 2 more cpu apps, then I get terrible laggy phone.
Sent via my FXP 046 MT15i®
sdk16420 said:
Same here, but I think that taaviu is right. I have ROM Toolbox and CPU Tuner installed, both can set the cpu.
Click to expand...
Click to collapse
does your phone throttles it's max frequency to 122mhz automatically and randomly too ?
also i only got setxperia , i.e no other cpu controlling apps , i may have installed setcpu before but i deleted it long ago before i start using setxperia !!
what do you think ? what could be the cause of this maybe some one can help us more ?
thanks all !
You don't lose anything if you uninstall setxperia.
And if problem after that dissapears...
Sent via my FXP 046 MT15i®
Here this has happened to me also
So there all right uninstall all apps that change CPU. And if any use just setcpu
If it's happens just a few times then no lasting damage just the fact it may not wake up for a bit but hitting power button fast sorts that just dont set these apps to run at boot and you should have no bother sorry just seen ya post n though ad say
Peace
Sent from my MT15i using xda premium
taaviu said:
That's my point.
I use cm7..there is built-in already cpu setting and when I use setcpu and 2 more cpu apps, then I get terrible laggy phone.
Sent via my FXP 046 MT15i®
Click to expand...
Click to collapse
i use FXP047 ... do we already have a cpu controlling app? where and what? i just installed set xperia...
chacho_2me said:
i use FXP047 ... do we already have a cpu controlling app? where and what? i just installed set xperia...
Click to expand...
Click to collapse
Under cynogen settings - perfomance - cpu settings.
Sent from my MT15i using Tapatalk
taaviu said:
Under cynogen settings - perfomance - cpu settings.
Sent from my MT15i using Tapatalk
Click to expand...
Click to collapse
hahaha..usually this part i dont touch..but now i did..thanks dude... hmmm.. any one here knows how to tweak it? like more power means more battery consumption? still.. i did install a game called fruit ninja..but at 1.4Ghz..still little bit lagging after few seconds of gaming...huhuhu...
chacho_2me said:
still.. i did install a game called fruit ninja..but at 1.4Ghz..still little bit lagging after few seconds of gaming...huhuhu...
Click to expand...
Click to collapse
This sounds like memory problem.
1,4Ghz is enough for playing.
What governor your using?
Sent from my MT15i using Tapatalk
i tried the ondemand and the smartass... and i still have the interactive and scarry that i still did not used.. about their differences on each governor, im not really quite sure... but hey..memory problem? hmm...so you mean to say that xperia neo should be enough to play this game? if yes..whats the problem with my phone?! huhuhu... i d have super box to free memory and cache mate forroot caches..hmmm... any way to help me dude?
@taaviu.. bdw, i did a fresh flash of fxp047.. still the same... cannot really play this game... if really memory problem..how to solve dude..any help please.. looks like if i cannot play this game..maybe other HD games .. I cannot play too?
Did you tried another HD games?
Set you cpu 500-1400 and governor ondemand and try then...
Sent from my MT15i using Tapatalk
hmmm...any hard memory game you can test for me dude?
chacho_2me said:
hmmm...any hard memory game you can test for me dude?
Click to expand...
Click to collapse
Im not big fan for games but iv tryed asphalt and nova. They played no problems even with stock.
Sent from my MT15i using Tapatalk
Please click one of the Quick Reply icons in the posts above to activate Quick Reply.
---------- Post added at 03:06 PM ---------- Previous post was at 03:05 PM ----------
ok..hope its about the app problem and not hardware..how about you try this game dude..little bit addicting..just for comparison sake... thanks dude
I saw some kernel wich is able to me to get 1228Mhz.But the default is 988Mhz sooo +240Mhz not a big thrust...So are there any way to get about 1,6Ghz or something like that?! I dont rly care about battery life! I have a Samsung i5800 (Galaxy3) and its CPU on default as i can rembember 688Mhz ... i use it on 1,4ghz...and theres no any overheat!So i think i cant fry the cpu!So i want to overclock my X10i...btw are there any way to overclock the GPU (Adreno 200) too?
Odp: How can i Overclock my X10i?
Metaton said:
I saw some kernel wich is able to me to get 1228Mhz.But the default is 988Mhz sooo +240Mhz not a big thrust...So are there any way to get about 1,6Ghz or something like that?! I dont rly care about battery life! I have a Samsung i5800 (Galaxy3) and its CPU on default as i can rembember 688Mhz ... i use it on 1,4ghz...and theres no any overheat!So i think i cant fry the cpu!So i want to overclock my X10i...btw are there any way to overclock the GPU (Adreno 200) too?
Click to expand...
Click to collapse
Haha, not possible. Set Your CPU to 1228 and You will see what happens.
Sent from my GT-I9100 using xda app-developers app
jakuburban said:
Haha, not possible. Set Your CPU to 1228 and You will see what happens.
Sent from my GT-I9100 using xda app-developers app
Click to expand...
Click to collapse
Its possible!--" I saw someone have 1401Mhz CPU speed....
Try go search all X10 kernels... Look at all the kernels' functions / features...
You might find out your ideal kernel and overclock your X10i to 1.4Ghz...
But honestly, you don't need so fast speed on this phone...
Sent from my GT-N7100 using xda premium
If the led turns white and the phone reboots, then the frequency is to high.
Highest I've seen was 1228 but not many chips can run that fast for long.
I stay at a stable 1190.
From Jaramie's X10a
Friends,
Help me, I am using Xperia Ray.
How to Configure CPU Control in my Ray.?
Is there any way to improve performance of phone using CPU control?
Which is best min Frequency and max Frequency for xperia Ray.
Thanks.
aravin said:
Friends,
Help me, I am using Xperia Ray.
How to Configure CPU Control in my Ray.?
Is there any way to improve performance of phone using CPU control?
Which is best min Frequency and max Frequency for xperia Ray.
Thanks.
Click to expand...
Click to collapse
hope u r already rooted..if not follow any rooting procedures in general tips and tricks forum..(one click root method was very successful in my wT19i,thanks to senior Nabeel :good
after rooting u can download setCPU or no frills cpu from playstore, to control ur CPU speeed..
very very detailed and easy descriptions regarding cpu control are already in those pages..so just check it out and dont wait simply till some experts reply to ur post..:good:
:good:
aravin said:
Friends,
Help me, I am using Xperia Ray.
How to Configure CPU Control in my Ray.?
Is there any way to improve performance of phone using CPU control?
Which is best min Frequency and max Frequency for xperia Ray.
Thanks.
Click to expand...
Click to collapse
I use Xperia Ray and
For rooting:
I used eRoot, you literally connect your phone to PC and pres ROOT
Before that you have to enable USB Debugging in Settings->Developer Options.
After four green circles get checked your phone is rooted
For CPU control:
I installed Custom ROM and there i have "no frills CPU control" installed. I don't recommend you to do overclocking or do anything with your processor because you can brick and mess up your device if you don't know what you'r doing.
Also, man already answered, you can download do frills from playstore
If i helped you, please don't forget to hit Thanks button
Cheers
Google link for eRoot, I'm still not able to post links
If you want to decrease lag raise the minimum frequency. Overclocking does absolutely nothing except making your phone hotter and processor life shorter
Sent from my LT18i using xda premium
tangosierra_ said:
If you want to decrease lag raise the minimum frequency. Overclocking does absolutely nothing except making your phone hotter and processor life shorter
Sent from my LT18i using xda premium
Click to expand...
Click to collapse
With overclock you are not 100% right with 1 ghz oc on ics some times i get scroll lagg and apps opens slower and with 1,4 ghz oc phone works perfect.
Ainster said:
With overclock you are not 100% right with 1 ghz oc on ics some times i get scroll lagg and apps opens slower and with 1,4 ghz oc phone works perfect.
Click to expand...
Click to collapse
The benefits of overclocking are still minimal.
Sent from my LT18i using xda premium
if you just want to reduce the lag , use SeederEntropy app , It's AWESOME !
*requires Root Permissions*
Hope It'll help
aravin said:
Friends,
Help me, I am using Xperia Ray.
How to Configure CPU Control in my Ray.?
Is there any way to improve performance of phone using CPU control?
Which is best min Frequency and max Frequency for xperia Ray.
Thanks.
Click to expand...
Click to collapse
CpU control lets u control ur phone cpu and its frequency and volatage.
increasing max freq. will increase speed but consume more battery.and risk of burning is also noteable.
so set it after doing research on ur cpu and itr limit.
and u need to be rooted and have a kernel to accses cpu
im using stock kernel. Can i overclock without flash custom kernel?
V4mpjr3 said:
im using stock kernel. Can i overclock without flash custom kernel?
Click to expand...
Click to collapse
No.
Sent from my Xperia Arc S using xda premium