I have the tablet for a couple of weeks now and the plastic cap on the micro usb charging port has a bent in the middle and wouldn't
close the hole tight any more.
Is it possible to replace the cap without sending the tablet to a service station ?
I have the issue on the charging port as well, let me know what you find out
kalda01 said:
I have the tablet for a couple of weeks now and the plastic cap on the micro usb charging port has a bent in the middle and wouldn't
close the hole tight any more.
Is it possible to replace the cap without sending the tablet to a service station ?
Click to expand...
Click to collapse
I sent mine to Texas after receiving RMA#. I've been waiting over 3 weeks to have it fixed. Tried to buy the cap but could not find it anywhere. I have only found port cover for Xperia phone Z but wasn't sure if they match those on the tablet. Anyway it is fixed now and recently I bought a cradle and it works great. I think it is a must to avoid damaging those covers. Pricey but I think it looks good, functions properly and it is great for watching movies, playing games and typing.
Bottom line send the tablet back to Sony and in the same time get a cradle and you will not have any issues with the tablet's waterproof tabs.
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
xlow78 said:
I sent mine to Texas after receiving RMA#. I've been waiting over 3 weeks to have it fixed. Tried to buy the cap but could not find it anywhere. I have only found port cover for Xperia phone Z but wasn't sure if they match those on the tablet. Anyway it is fixed now and recently I bought a cradle and it works great. I think it is a must to avoid damaging those covers. Pricey but I think it looks good, functions properly and it is great for watching movies, playing games and typing.
Bottom line send the tablet back to Sony and in the same time get a cradle and you will not have any issues with the tablet's waterproof tabs.
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Thanks. I am sure the cradle is the best solution but not very practical when traveling and charging on the road on trains or air plains.
the cap must have a design flow if it breaks only after a couple of weeks.
Agreed. It was not the greatest engineering marvel. Cradle is in fact very thin and it fits the tablet very snug so I don't see any problem of taking it with me when I go. The threaded plug port with an o-ring would have been much better solution than that cheesy tab. But then again not many people would have bought a cradle. It is a good product but like most electronics it has its flows. My advice try not to open those tabs too often or better avoid opening them altogether. They will last forever. Bluetooth headphones, cradle, WiFi can easily facilitate it.
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
I would prefer that Sony replaced these, but they told me that when the tiny piece of plastic bends and breaks that it's considered physical damage. I find that odd that a main selling point is its resistance to damage but the part that protects from damage breaks off with normal use. I had to settle for replacement covers I found on ebay.
badwiring said:
I would prefer that Sony replaced these, but they told me that when the tiny piece of plastic bends and breaks that it's considered physical damage. I find that odd that a main selling point is its resistance to damage but the part that protects from damage breaks off with normal use. I had to settle for replacement covers I found on ebay.
Click to expand...
Click to collapse
I also bought one from ebay but i have no idea how to replace it. did you already replace it and if so how ?
I had this situation that the cap got bend because I forgot to put it back after closing the tablet cover over it. I was able to bend it a bit the other side and also notice the little pin needed to be straighten so that it will fit back in place. This is when I notice the hole next to the usb to be used when the cap is open you insert the cap pin in it.
badwiring said:
I would prefer that Sony replaced these, but they told me that when the tiny piece of plastic bends and breaks that it's considered physical damage. I find that odd that a main selling point is its resistance to damage but the part that protects from damage breaks off with normal use. I had to settle for replacement covers I found on ebay.
Click to expand...
Click to collapse
MikeViller said:
I had this situation that the cap got bend because I forgot to put it back after closing the tablet cover over it. I was able to bend it a bit the other side and also notice the little pin needed to be straighten so that it will fit back in place. This is when I notice the hole next to the usb to be used when the cap is open you insert the cap pin in it.
Click to expand...
Click to collapse
i noticed that a while ago but when i searched for that hole on the internet it said it was to vacuum seal it or something so i decided to not put it in there. but did you find a way to remove the cap ?
them4tti said:
i noticed that a while ago but when i searched for that hole on the internet it said it was to vacuum seal it or something so i decided to not put it in there. but did you find a way to remove the cap ?
Click to expand...
Click to collapse
no there's not need for me to remove it close perfectly .... but if you take the manual it says hole for cover
You need to remove the back panel first. There is a video on yt. Seems easy to do it.BTW where did you get those tabs??? Can you send a link?
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
I don't know if that could work as a replacement part: something that looks like the current part, but with an extra rubber plug that would fit inside the mini usb port to hold it in place...
Seems like I now have a reason to get a 3D printer :S
**EDIT***
I remembered something I saw a few years back, is called Sugru, a moldable rubber that cures and can be used for almost anything. Search them out on Google.
xlow78 said:
You need to remove the back panel first. There is a video on yt. Seems easy to do it.BTW where did you get those tabs??? Can you send a link?
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
Click to expand...
Click to collapse
well the problem with removing the back is that it is not waterproof any more when you put it back on
here is a link from where i got mine : battery-cover.de/product_info.php?info=p102_abdeckung-usb-anschluss-tablet-z-weiss-black.html
Btw are you talking a bout a video of replacing the cap or a video about dissabling the tablet ?
From what I've seen the tab cover has a "nipple" which can be squeezed and pushed through the hole (from the inside of the tablet). I don't think it is easily or even possible to do it from the outside. Besides I think the back panel acts like a gasket and seals the inside so I don't understand why would the tablet lose its waterproof capability. Do you have any bad experience?? Besides I don't see why could not you smear very fine silicon layer around the mating parts and make it 100% waterproof! Disassembly is here: http://m.youtube.com/watch?v=zczfTnBFqtA
Good luck and let us know how did you make out.
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
Caps:
black
black
white
The price ofc. is terrible for so small thing.
It is a pure rip off. Piece of plastic and rubber priced like silver! Even more reasons now to buy the cradle. Too bad you can't use it for USB transfer. It is a big design flaw and I have no idea why did Sony make such cheap and lousy part!
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
.
i decided i am going to send it to sony. this is because my screen started acting weird and i hope they can replace the cover to.
kalda01 said:
I have the tablet for a couple of weeks now and the plastic cap on the micro usb charging port has a bent in the middle and wouldn't
close the hole tight any more.
Is it possible to replace the cap without sending the tablet to a service station ?
Click to expand...
Click to collapse
Search for "USB Cap USB Side Cap Sony Xperia Tablet Z" on ebay, a seller from spain has them, not cheap ($17 usd including shipping), but at least somewhere to find it.
I broke mine and about to order it, what I wonder is how do I remove the still attached plastic part without opening the entire thing...
can anyone provide a link to instructions or video how to replace audio jack port cover? Thanks in advance
Apo11on said:
can anyone provide a link to instructions or video how to replace audio jack port cover? Thanks in advance
Click to expand...
Click to collapse
I've found this
witrigs.com/blog/in-this-way-you-will-replace-sony-xperia-z1-sim-card-sd-card-usb-cover-flap-easily/
I think it's similar
Related
Anyone knows where to get a replacement? I think it's what it's called. It's the small plastic cap on top of the phone over the cable socket. Lost mine at some point...
There is probably no replacement for this. Either live with it or replace the whole housing.
http://www.dealextreme.com/details.dx/sku.37131
New Case for Cheap!
stgeorge88 said:
Anyone knows where to get a replacement? I think it's what it's called. It's the small plastic cap on top of the phone over the cable socket. Lost mine at some point...
Click to expand...
Click to collapse
Same situation here.. your best bet is this....
http://www.dealextreme.com/details.dx/sku.37130
Pricy~
Thanks for you all. I'll keep looking and keep you guys posted
Sent from my X10i using XDA App
Why would you replace an entire case for a lost dust cap?
I'd be very happy if that thing fell off. Makes it impossible to plug charger in in the dark or with one hand!
Sent from my X10i using XDA App
Punnisher_42 said:
I'd be very happy if that thing fell off. Makes it impossible to plug charger in in the dark or with one hand!
Sent from my X10i using XDA App
Click to expand...
Click to collapse
You mean they last more that two days then It is so much easier to connect the cable without it - shame there isn't a thing to fill the holes it leaves behind though (aside from the USB one that is).
Go to a site called "netimes.com" and type "micro usb" into there search box .I.ve ordered a pair already, will let you know what they're like when they arrive.
Fahrvergnugen said:
http://www.dealextreme.com/details.dx/sku.37131
New Case for Cheap!
Click to expand...
Click to collapse
The black casing does not show the dust cap, whereas the white casing does...
Yup, true genius engineering design went into that usb connector. (Same guy tested the in-call volume in a sound proof room).
What?!?! Put the connector at the bottom and be like everyone else?? No X10 owner would want to put the device into a docking stand. That would just be foolish.
My previous phone, an HTC Cruise, has the connection at the bottom with no cover. In more than a year of being in my shirt pocket on a daily basis the mini-usb never got any dust in it. At least not enough to ever prevent a good usb connection.
I've had my Rezound for just over two weeks and the MHL port housing is loose! I can literally flick the rectangle shaped black housing around with my finger
I purchased through Amazon as part of the Penny Pincher sale. Anyone else have this issue? I'm debating whether I should do a warranty exchange. When my phone vibrates it makes a loud noise due to this and I'm afraid it might get worse in the future.
Live with it or exchange?
gsiax100 said:
I've had my Rezound for just over two weeks and the MHL port housing is loose! I can literally flick the rectangle shaped black housing around with my finger
I purchased through Amazon as part of the Penny Pincher sale. Anyone else have this issue? I'm debating whether I should do a warranty exchange. When my phone vibrates it makes a loud noise due to this and I'm afraid it might get worse in the future.
Live with it or exchange?
Click to expand...
Click to collapse
Exchange. Having a function like that broken sucks, and mhl has been kind of finnicky for me anyway.
Sent from my ADR6425LVW using xda premium
Exchange!!!
That is an important port used for everything. Charging, data hook up, output to TV etc...
My old phone's port got damaged and even though it wasn't a smart phone it sucked to not be able to hook it up as data and to have weak charging because of it. Had to buy an external battery charger for the last few months of owning it to keep it functional since it started having trouble charging at all. And then I had to copy each pic one at a time to the sd card so I could salvage them because I couldn't hook it up as data.
I also purchased mine for a penny from Amazon and mine has been trouble free.
My wife and I have had this problem on the 2 replacement phones we have each gotten from Amazon. The originals didn't exhibit this behavior. We are going to get two more replacements and hope that they don't show the same issue. It is the black plastic bezel around the port that is loose.
fyi, i don't think the plastic bezel is attached to the actual charging port... so if that's lose, it doesn't really matter as long as the port is soldered firmly to the board.
Sent from my ADR6425LVW using XDA App
jayochs said:
fyi, i don't think the plastic bezel is attached to the actual charging port... so if that's lose, it doesn't really matter as long as the port is soldered firmly to the board.
Sent from my ADR6425LVW using XDA App
Click to expand...
Click to collapse
Exactly. I've had 2 Rezounds, same on both, it's just the bezel, not the port. It is slightly annoying that it rattles when the phone vibrates though.
Anyone have any recommendations?
Check eBay or.amazon for a new one. They are cheap and come in a bundle.
Sent from my C6806 using XDA Premium 4 mobile app
Thanks, you have an Amazon link? Not having luck there.
rockky said:
Anyone have any recommendations?
Click to expand...
Click to collapse
Buy from somewhere else and replace by yourself or take to sony but this will charge you because not cover by warranty.
Only place is Ebay. Takes 21/2 weeks to get.
atrix2 said:
Buy from somewhere else and replace by yourself or take to sony but this will charge you because not cover by warranty.
Click to expand...
Click to collapse
Weird though, I just called Sony in Canada and they are willing to fix/replace my phone that has screen problems, usb port flap came off and speaker problems.
Why can't you just buy the part and they send it? (U have to send the device for that silly little piece right?)
I'm also interested cos I have the same problem
rockky said:
Why can't you just buy the part and they send it? (U have to send the device for that silly little piece right?)
Click to expand...
Click to collapse
If you guys find a place where to buy please post it I've been looking for it with lo lockangel:
They're on eBay.
Sony needs to change this design...Or...send a couple extra with the device
Buy a magnetic charging cable! Saves the port! Yes you'll still need to open the port for communication of copying files from PC but it would be substantially less compared to opening the port to charge everyday.
Jammol said:
Buy a magnetic charging cable! Saves the port! Yes you'll still need to open the port for communication of copying files from PC but it would be substantially less compared to opening the port to charge everyday.
Click to expand...
Click to collapse
Too bad I use the USB port for my DAC.
rockky said:
Only place is Ebay. Takes 21/2 weeks to get.
Click to expand...
Click to collapse
Could someone kindly furnish me with an actual link. Searching for seal didn't bring up anything. I am very much obliged! :fingers-crossed:
lsauer said:
Could someone kindly furnish me with an actual link. Searching for seal didn't bring up anything. I am very much obliged! :fingers-crossed:
Click to expand...
Click to collapse
http://www.ebay.de/itm/Original-Son...zer_Ersatzteile_Werkzeuge&hash=item2339fdd95e
If you don't wonna buy new cup, you can buy cheap glue gun,
then you put some glue on your cup, make the hole a little wet, so your glue want stick.
then wait few secs until glue will become a bit harder and close the cup.
Finally, after it will be hard enough, you can cut with razor glue you don't need.
And yeah, you can always warm up that glue with lighter, if you need to do step 2 again.
Works for me, even tested under water, but not for a long time though :good:
madphone said:
http://www.ebay.de/itm/Original-Son...zer_Ersatzteile_Werkzeuge&hash=item2339fdd95e
Click to expand...
Click to collapse
Bought this works great
Sent from my SM-P900 using XDA Free mobile app
From the link it shows the whole flap (w/ rubber gasket). When you said that it works great, did you replace the entire flap or pull the rubber gasket off of the new one and put it onto your current one?
Thanks,
Gery
gerizafa said:
From the link it shows the whole flap (w/ rubber gasket). When you said that it works great, did you replace the entire flap or pull the rubber gasket off of the new one and put it onto your current one?
Thanks,
Gery
Click to expand...
Click to collapse
you cant replace the rubber gasket....it wont stick. And I tried locktite 401, and it ruined the whole gasket instead of setting it in the right position....perhaps you can do it. But you need a microscope
Thanks! I've found a video on youtube showing how to remove the old one for putting the new one on!
GT
Hello all,
Any of you had any issues with the magnetic charging port on your Z2 coming lose? Mine has. Pulled it off the magnetic charging dock and the port was left of the dock.
Please post a picture
Sent from my D6503 using Tapatalk
i dont have any issues with my port. i dont use dock.. but i have the magnetic connector.. the magnetic port is held by a clip in the other side of the metal frame, i think that might have released your port.. thats an easy fix..but u need to disassemble the phone..
this is what came out...
Return the phone at once to where you made your purchase. Insist on either a new phone or a full refund. No brainer.
Let us now how you get on. Good luck and stand your ground!
Ryland
roninr1c said:
this is what came out...
Click to expand...
Click to collapse
LOL
roninr1c said:
this is what came out...
Click to expand...
Click to collapse
OMG. Even a junkyard magnet won't be able to do that with the phone!
Sent from my D6503 using XDA Premium 4 mobile app
Haha, this is really awkward. I hope Sony will fix this for you - looks really like a problem on the manufacturing side.
I wonder if the water resistant capability is vulnerable because of this, can you see internals thru holes after the dock?
sevoflurane said:
OMG. Even a junkyard magnet won't be able to do that with the phone!
Sent from my D6503 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
It would, the magnetic port isn't soldered in, those two contact Strips Look like they just plug into something
Sent from my D6503 using Tapatalk
The same issue in South Korea.
roninr1c said:
Hello all,
Any of you had any issues with the magnetic charging port on your Z2 coming lose? Mine has. Pulled it off the magnetic charging dock and the port was left of the dock.
Click to expand...
Click to collapse
I'm sorry, bad English.
Several cases occurred in the same issue, even in our country.
But the problem is the fault of the customer, according to Sony service center.
Many people are angry, but they do not change attitudes.
Sony's quality control is questionable, but they do not recognize it either.
I hope you look forward to a good result. Please let us know results later!
I tohught i'd found someone that had the charging port always crooked problem this is much different.
that is something to look out for.
Worried now as i use the magnetic port exclusively.
This just happened to me today. I removed my phone from the dock this morning and the port was detached from the phone and was stuck on the dock its already my second phone as the first one had digitizer lines, gaps etc.
I'm on my third device now. Just happened to me on monday but I was using a third party charging cable.
it looks like the port is just glued in with the contacts being pushed into the phone. I would have thought they would have made it with a lip so it could not be pulled out!? or is that to much like common sense lol.
This is hilarious, I can't believe this have happened to the charging port, it looks very sturdy.
i was planning to buy this (it has really good reviews, 5 stars on all the reviews,.... although its only like 9 people that reviewed it)
http://www.amazon.com/Magnector-Per...402475479&sr=8-4&keywords=z2+magnetic+charger
it says that it has twice the Magnetic Power than original Sony Xperia Charging Cable.... that sounds good because i heard the original one is kinda weak and disconnects easy,.... but in the other hand it increases the possibility of making the magnetic port loose,.....
has anyone tried this product yet????
stargate1000 said:
I'm on my third device now. Just happened to me on monday but I was using a third party charging cable.
it looks like the port is just glued in with the contacts being pushed into the phone. I would have thought they would have made it with a lip so it could not be pulled out!? or is that to much like common sense lol.
Click to expand...
Click to collapse
Common sense does not exist in the corporate world. They are mutually exclusive (save for some extenuating circumstances).
So how does this affect waterproofing, is the phone stilled even if the port isn't in?
If it is then I wouldn't mind having to put dab of glue and shove it back in if mine ever came out.
If it's not then it might have been a leakage point for some of the people that ended up with moisture inside after phone is submerged.
I guess I'm going to have look for those tear down photos & see if it shows details of the frame/magnetic port.
Sent from my D6503 using Xparent Red Tapatalk 2
Well this is awkward. My port just came loose after using Sony original magnetic charger. Darn that's annoying, guess I have to return it. Should I relock the Bootloader? It doesn't have anything to do with software..
Sent from my D6503
I just sent it for repair, not sure if they can fix it or I get a new phone. Hopefully it's not "my fault". I will update when I hear from them.
Please update me, mine did not come out but at the opposite it looks like it's being pushed in, there is a tiny gap showing on the left side as if it's going to fall inside the phone from one side.
Anyone else having physical problems with their Z2?
As of a few weeks ago, I've started noticing that the top right corner of the back panel of my Z2 popping up slightly (like 2mm to 3mm) several times a day and I would have to press it back down. The cover on the USB/SIM area will also mysteriously be open sometimes when I fish the phone out of my pocket even though it does still feel quite firmly closed once I put the cover back in place.
I went down to my local Sony service centre and they said that they will rectify the issues for me and might replace the "loose" flap too (also told me to avoid water since it's not waterproof with the back like that) - but it would take 7 working days and that I should call their helpline to check if there was any issue for me sending my set in as it has an unlocked BL.
Seems like the original Z had the same problem with the back cover - http://www.xperiablog.net/2013/08/0...ose-back-panels-water-resistance-compromised/ and the loose flaps issue isn't new either (but the rubber seals on mine look perfect).
Flash a stock kernel and relock your bootloader, few people actualy check these days for DRM keys however they do check rarely for your bootloader status
And your physical problems are totaly abnormal so try very hard to get a replacement
Sent from my D6503 using XDA Premium 4 mobile app
for the flap problem, easy easy fix. Get some silicone grease at your hardware store or wherever. Take a lil and moisturise the flaps' rubber, works like a charm. Seems like the seal just dries out.
hotnikkelz said:
for the flap problem, easy easy fix. Get some silicone grease at your hardware store or wherever. Take a lil and moisturise the flaps' rubber, works like a charm. Seems like the seal just dries out.
Click to expand...
Click to collapse
I just tried it and it seems to make the flap come loose more easily. Looking at the flap, it seems to pop open because of insufficient friction between the seals and the socket for the flap...
benengyj said:
I just tried it and it seems to make the flap come loose more easily. Looking at the flap, it seems to pop open because of insufficient friction between the seals and the socket for the flap...
Click to expand...
Click to collapse
You didn't cake it on I hope. You're putting a really small amount. Like really small. It worked for me. Sowwy
Sent from my D6503 using Tapatalk
OMG what a ****ty phone. I will never buy Sony again. I have only problems with this crap.
hotnikkelz said:
You didn't cake it on I hope. You're putting a really small amount. Like really small. It worked for me. Sowwy
Sent from my D6503 using Tapatalk
Click to expand...
Click to collapse
Is this same as CPU's thermal paste?
hotnikkelz said:
You didn't cake it on I hope. You're putting a really small amount. Like really small. It worked for me. Sowwy
Sent from my D6503 using Tapatalk
Click to expand...
Click to collapse
I just applied this - http://www.wd40specialist.com/products/silicone-lubricant/) - thinly using a q-tip. No worries. Wasn't too expensive and it could be closed again once I cleaned it off. Tried a slightest touch of hair gel (I was desperate...LOL) and that didn't work too well either.
I guess I'll just try to relock the BL and feign ignorance and send it in for "hardware faults" even though the bored sounding helpdesk lady on the phone said that the warranty is voided.
misiakr said:
OMG what a ****ty phone. I will never buy Sony again. I have only problems with this crap.
Click to expand...
Click to collapse
Genuinely quite disappointed with the niggling faults that the phone has. Random freezes and self-reboots and WIFI issues on my Z2 and my dad's Z1 is making me lose confidence in Sony to deliver a solid all-round device. It's a really beautiful phone with a wonderful camera but compared to build quality and software stability my previous HTC M7 (converted to a GPE ROM) which was essentially bulletproof and could have months and months of uptime without a reboot...ugh.
benengyj said:
Anyone else having physical problems with their Z2?
The cover on the USB/SIM area will also mysteriously be open sometimes when I fish the phone out of my pocket even though it does still feel quite firmly closed once I put the cover back in place.
Click to expand...
Click to collapse
I also have the loose USB flap problem. I've ordered a new one, I hope this will fix the problem.
It seems like sonys new factory has screwed the Z2 lol
My first Z2 brand new the back plate was lose enough for it to fall out and it did a few times also has all the probs mentioned in the op post
This new one is fine ,no reboots, no blackouts,no lags, no crashss bugs no probs
Sent from my D6503 using XDA Premium 4 mobile app
Envious_Data said:
It seems like sonys new factory has screwed the Z2 lol
My first Z2 brand new the back plate was lose enough for it to fall out and it did a few times also has all the probs mentioned in the op post
This new one is fine ,no reboots, no blackouts,no lags, no crashss bugs no probs
Sent from my D6503 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I think that only the loose USB flap is a very recurrent problem.
nreuge said:
I think that only the loose USB flap is a very recurrent problem.
Click to expand...
Click to collapse
It seems like it too because my USB flap isnt neccisarily lose, it seems to sit deeper in the frame, it isnt flush with the rest of the frame or like my SDCard Slot
Sent from my D6503 using XDA Premium 4 mobile app
For me, the flaps are good, and the back panel on the edges doesn't seem to pop up or to be misaligned with the edge, but on a light press on a few places it feels like the back panel is loose, and you can hear a small "tactile" feedback when pressed.
Should i get it checked or is it just a little hollow on these few places? For me that's the spot a little to the left and bottom of the SONY logo on the back, in height of the volume rocker.
tomaach said:
For me, the flaps are good, and the back panel on the edges doesn't seem to pop up or to be misaligned with the edge, but on a light press on a few places it feels like the back panel is loose, and you can hear a small "tactile" feedback when pressed.
Should i get it checked or is it just a little hollow on these few places? For me that's the spot a little to the left and bottom of the SONY logo on the back, in height of the volume rocker.
Click to expand...
Click to collapse
me too... but imho it isn't a problem...
I kinda semi-fixed the loose flaps by cleaning off the accumulated dust around the edges of the seal and the covered area...doesn't seem to fall out as often now.
Envious_Data said:
It seems like it too because my USB flap isnt neccisarily lose, it seems to sit deeper in the frame, it isnt flush with the rest of the frame or like my SDCard Slot
Sent from my D6503 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I've received my new USB flap and the issue is fixed, the new flap is not loose. It was not due to the phone body as I feared but a premature wear of the flap...
Anyway, I don't recommend to open the flap but in exceptional circumstances. Transferring files wireless and charging phone with magnetic port should be the rule and recommended by Sony.
benengyj said:
I kinda semi-fixed the loose flaps by cleaning off the accumulated dust around the edges of the seal and the covered area...doesn't seem to fall out as often now.
Click to expand...
Click to collapse
Can you explain why you have not returned your mobile under warranty for repair or replacement?
Ryland
nreuge said:
I've received my new USB flap and the issue is fixed, the new flap is not loose. It was not due to the phone body as I feared but a premature wear of the flap...
Anyway, I don't recommend to open the flap but in exceptional circumstances. Transferring files wireless and charging phone with magnetic port should be the rule and recommended by Sony.
Click to expand...
Click to collapse
My flap has been back to normal since cleaning out the dust from around the silicone seal.
Ryland Johnson said:
Can you explain why you have not returned your mobile under warranty for repair or replacement?
Ryland
Click to expand...
Click to collapse
To be honest, it's just the hassle of having to wait a week (and having to go back to my HTC M7) or so for them to get it fixed. Plus my set might not be accepted by them as the BL is unlocked (towelroot came too late for me unfortunately )
I do intend to send it in for repairs (also dinged the flap a little, might as well get that swapped out too) some time soon as the loose back is really REALLY bugging me.
My god I have the same problem. Everytime I pull it out of my pocket the flap is out. Damn this phone was perfect . I cleaned soo ****ing well and the USB flap stays in more time but its still poping out.