Related
Hey guys - does anyone know of any after-market battery covers for the HD that would be metal - specifically for the purpose of attaching to a magnet? I purchased one of those magnetic "cradle" kits that is basically just a big magnet you stick onto whereever, with a little metal slab that you stick onto the back of your phone. Then - you can just stick the phone up close to the magnet and it sticks - a perfect low-profile car cradle. The metal slab that sticks to the back of the phone is thin - it doesn't really stick out any further than the camera housing - but it still isn't as sleek as just the phone by itself. I thought a replacement battery cover that sticks to the magnet would be perfect. So... does anyone know of any? Or perhaps a vendor that could custom-machine one?
SolusCado said:
Hey guys - does anyone know of any after-market battery covers for the HD that would be metal - specifically for the purpose of attaching to a magnet? I purchased one of those magnetic "cradle" kits that is basically just a big magnet you stick onto whereever, with a little metal slab that you stick onto the back of your phone. Then - you can just stick the phone up close to the magnet and it sticks - a perfect low-profile car cradle. The metal slab that sticks to the back of the phone is thin - it doesn't really stick out any further than the camera housing - but it still isn't as sleek as just the phone by itself. I thought a replacement battery cover that sticks to the magnet would be perfect. So... does anyone know of any? Or perhaps a vendor that could custom-machine one?
Click to expand...
Click to collapse
I made my own magnetic car holder solution. Didn't cost much and can't imagine it work better than this...
I can't see what you've done there... It looks like some sort of metal on the battery itself, so that the regular cover works fine... What is that? How is it affixed?
Jouh has placed 2 razor blades on the battery.
Cool! I'm going to try that...
just don't take ur phone to the airport...... they might think ur going to use the razorblades for other non magnetic purposes.
Ohh! Good point! I would have completely forgotten about them and then been really screwed - I actually have to run my mobile through an X-ray every day at work... That could be an issue. Oh well - back to the drawing board...
just do the same with any thin metal i.e. sheet steel.
spzero said:
just do the same with any thin metal i.e. sheet steel.
Click to expand...
Click to collapse
I really wouldn't recommend directly attaching the phone to strong magnetic sources. It may impede the functionality, reduce or affect the battery operation, interfere with the many antennas in the phone, not to mention run the risk of corrupting memory sticks etc?
The phone itself isnt that heavy so probably wouldnt need a strong magnet, but you'd want to use something quite strong just to hold it in place. Imagine driving over a speed bump or pot hole which dislodges the phone and makes it go sliding across your dash board and out of an open window. (worst case scenario..)
If youre looking for a quick release holder I would recommend something that you clip the phone into like those hip holsters and then find one that has a socket connection to a window mount.
makaveli2g said:
I really wouldn't recommend directly attaching the phone to strong magnetic sources. It may impede the functionality, reduce or affect the battery operation, interfere with the many antennas in the phone, not to mention run the risk of corrupting memory sticks etc?
The phone itself isnt that heavy so probably wouldnt need a strong magnet, but you'd want to use something quite strong just to hold it in place. Imagine driving over a speed bump or pot hole which dislodges the phone and makes it go sliding across your dash board and out of an open window. (worst case scenario..)
If youre looking for a quick release holder I would recommend something that you clip the phone into like those hip holsters and then find one that has a socket connection to a window mount.
Click to expand...
Click to collapse
I used the same razors and the same magnet (This one) with my SE P1i for 1½ year without any issues.
And the phone doesn't move 1 mm even driving over the biggest speed bump in Sweden.
makaveli2g said:
I really wouldn't recommend directly attaching the phone to strong magnetic sources. It may impede the functionality, reduce or affect the battery operation, interfere with the many antennas in the phone, not to mention run the risk of corrupting memory sticks etc?
The phone itself isnt that heavy so probably wouldnt need a strong magnet, but you'd want to use something quite strong just to hold it in place. Imagine driving over a speed bump or pot hole which dislodges the phone and makes it go sliding across your dash board and out of an open window. (worst case scenario..)
If youre looking for a quick release holder I would recommend something that you clip the phone into like those hip holsters and then find one that has a socket connection to a window mount.
Click to expand...
Click to collapse
I honestly couldn't think of one thing that a magnet could have an effect on in the phone, certainly not the memory. The only type of memory that is affected by magnets are HDD (because the data on the disks is stored magnetically) and credit cards (once again, data stored magnetically). However, RAM/ROM is completely different and relies on gates and latches to store data, neither affected by magnet. Not to mention even if it did have an HDD (like old school mp3 players/iPod) it would take a strong magnet (mainly electromagnet) to corrupt the memory. Likewise, I can't foresee it having any affect on the battery or interfering with the antenas (unless you're using some super strong magnet....which you're likely not)
One of the only build quality problems i have with the Touch HD is that the battery cover creaks when pressed in certain spots.
To revive this topic, does anybody know of an actual aftermarket battery cover for this phone, preferably metal?
I searched google to find no results. It seems like it would be a good idea to make these
You can also shave the inside of the battery cover with a small sander. Than add ANY kind of magnet that will than fit inside the cover. The plastic cover is THICK so you can shave enough for some type of magnet.
I would also like a metal/rubber etc back cover. The quality of the orginal cover is driving me nuts..
Has anyone found this kinda aftermarket item?
sudo_x60s said:
I would also like a metal/rubber etc back cover. The quality of the orginal cover is driving me nuts..
Has anyone found this kinda aftermarket item?
Click to expand...
Click to collapse
Any news on that topic?
Well, since it's taking so long for both Asus and 3rd parties to come with accessories for the transformer, I decided to take advantage of some foamcore scraps I had, and made me a "dock" for videochat, video watching and gaming. I say it's a "dock" because it is simply a bunch of foamcore boards, paper and glue (I'll probably seal it, sandpaper it, and paint it)
Right now, it's very handy, for using the tablet without having to hold it. It's angled, at a very confty angle, and doesn't get in the way (the keyboard dock, while awesome, gets in the way)
I had the images in my Dropbox gallery, but had to attach them because I'm a new user though a long time lurker. The good thing about putting them in the dropbox would be that I could add and update the pics at any time, without having to come back to the post, and edit it. Oh, and the picstures would be clearer, since I'm taking them with a 12 MPixel cam. Well, at least it keeps linkspam out of XDA
I must admit I am thinking of making my own dock via the use of a decorative plate stand (you know the ones, fold open to 90 degrees, have a lip at the bottom)
Like this one
Pretty cool idea there, but I have a question.. You can find your apps on that home screen?? It's crazy!
ericcarboni said:
Pretty cool idea there, but I have a question.. You can find your apps on that home screen?? It's crazy!
Click to expand...
Click to collapse
Yes I can, but I agree that it's not for everybody. What I do, is having the apps grouped spacially. 90% of the apps I use are on that screen. I really don't like going to the app drawer
you can always use a "folder type" system like smart shortcuts so u can categorize apps into "folders".
The plate idea is cool but ya might want to check out the arkon stand. same concept but its collapsible.
http://www.amazon.com/IPAD-ST-Unive...2?s=electronics&ie=UTF8&qid=1312309239&sr=1-2
I use one of these at work (we have plenty in the supply closet):
I just put it on there upside down and let the screen rotate 180 degrees so I can plug in the charger up top. I can also put books of various sizes on the back end, to adjust screen angles.
@carrrnuttt - lol, thats brilliant
(..although i'd add some nice felt between the 'stand' and TF)
In case anyone was wandering (as i was) - this is a Black Mesh Business Card Holder - so you can pretend that is what you'll use it for
stujuk said:
I must admit I am thinking of making my own dock via the use of a decorative plate stand (you know the ones, fold open to 90 degrees, have a lip at the bottom)
Like this one
Click to expand...
Click to collapse
I have this, the only issue i have with it is it does not lean back enough.
Why not just buy a cheap leather folio case for the transformer for $10 from ebay, they all have the ability to stand the TF up at an angle for video viewing/video chat etc
such as this one
brett_day said:
Why not just buy a cheap leather folio case for the transformer for $10 from ebay, they all have the ability to stand the TF up at an angle for video viewing/video chat etc
such as this one
Click to expand...
Click to collapse
I've got one of those and I have to say it's not very good when you've got the Transformer oriented the normal way (camera at the top) because the flap that covers the bottom (Dock connector) doesn't hold well so the tablet slides down quite a bit. Great as a standard case for holding, and having with the camera at the bottom, but not so great with you have it stood with the camera at the top.
ant_thomas said:
I've got one of those and I have to say it's not very good when you've got the Transformer oriented the normal way (camera at the top) because the flap that covers the bottom (Dock connector) doesn't hold well so the tablet slides down quite a bit. Great as a standard case for holding, and having with the camera at the bottom, but not so great with you have it stood with the camera at the top.
Click to expand...
Click to collapse
I have this case and it works perfectly. Super snug fit, no slippage, anyway, just thought i would throw that out there. I am happy with mine.
Found a way to charge mine while it is the right way around in my home made dock too.
The case hooks onto the edge of the dock leaving enough gap to plug in the charger
The plastic dock is from my GFs laptop, supposed to be a stand for that, and the thing I bent into a pyramid is a leather place mat
---------------
brett_day said:
I have this case and it works perfectly. Super snug fit, no slippage, anyway, just thought i would throw that out there. I am happy with mine.
Click to expand...
Click to collapse
Maybe mine was an early model and wasn't designed too well.
Hi guys, i've noticed recently when connecting the dock that the two slots on the bottom of the twblet are becoming slightly chipped/scratched. Does this happen to anyone else? Its only a mijor thing but its slightly annoying.
Mine's not chipping/scratching, yet. But, then again, if you saw how carefully I dock/undock, you would understand why. Looking forward to my first scratch/chip, so I can relax a bit and stop being so careful...
One of my slots has a slight nick on it from the dock. But you really have to go looking for it to see it. I would suggest just being careful how well you line up the keyboard and the tablet when you connect them in order to minimize any scratches that would annoy you. There are alignment arrows on the center of the dock and the bottom of the tablet.
well after dropping my first one from about a height of 4 feet (in the neoprene sleeve in the accessory section) and watching with horror as it bounced on an edge...and luckily was able to return it due to other issues....looked with less fear...
then my wife accidently dropped the new tablet..again in said neoprene sleeve...and although dinged on the edge..not nearly as bad as the first.
Moral? the harder you try to keep something pristine..the more likely it will get blemished faster :S
Having something like the dock feature..you are fundamentally going to get scuffs...it's the way it works when you introduce metal on metal.
worse case is when you take out the dock...and the gel's are available...put one on after undocking..that's what i plan on doing..as this thing is a slick bugger.
Guys...
I've had my C6802 for a week now. I've been loving it, and I didn't understand why people are dissing it about pocket ability. It fits in my pants pocket just fine. I just make sure that the left front pocket is reserved for the phone alone, no keys, change, or any other scratcher. Breast pocket is just disaster waiting to happen - button down flap can't even come over the phone. So that's out.
Today I sat down at the restaurant to use the Wi-Fi on my laptop, and I hooked up the XZU to download a movie through Media Go. I noticed the phone rocking back and forth diagonally, not laying flat on the table top. I thought maybe the table is sloping on that side. So, I moved the phone to another spot; same thing. I picked up the phone and eyeballed it along its profile! Alas! It was bent!
I remembered...... Aluminum frame..... so I flexed it diagonally to fix it, and it straightened out!
So be warned folks! Even if it fits in your pocket, sitting down with the phone in the pocket will definitely bend it! This might even lead to the glass corners popping out!
Oh, that's.. bad I usually put my phone on the table no matter what, but i'll keep this in the back of my head. Thanks for sharing.
LordManhattan said:
Oh, that's.. bad I usually put my phone on the table no matter what, but i'll keep this in the back of my head. Thanks for sharing.
Click to expand...
Click to collapse
I do set the phone on the table too. I believe I twisted it sitting in the car from the house to the restaurant. It was a short drive; 2 blocks. So I didn't think much of it.
post a youtube video or pics to let us see, as this is sorta scary and might become usual as if this happens to more than yourself at least we can all tell sony support its a common fault
yup, there was a thread somewhere, someone asking how much it costs to replace the screen/digitizer because the screen cracked when he sat on it while ZU in the back pocket.
Gotta be careful...
---------- Post added at 06:04 PM ---------- Previous post was at 06:00 PM ----------
encryptioncsta said:
post a youtube video or pics to let us see, as this is sorta scary and might become usual as if this happens to more than yourself at least we can all tell sony support its a common fault
Click to expand...
Click to collapse
I wonder, from what point it stops being a faulty design... I mean, not all of us are made the same. If a 200kg (about 400lbs?) guy sat on it at the wrong angle, I would not blame Sony at all... A steel sheet 5mm thick will bend under those kinda weight...
jewelkobayashi said:
I wonder, from what point it stops being a faulty design... I mean, not all of us are made the same. If a 200kg (about 400lbs?) guy sat on it at the wrong angle, I would not blame Sony at all... A steel sheet 5mm thick will bend under those kinda weight...
Click to expand...
Click to collapse
Even if someone of 40 kg would sit on it while on the rear pocket I would not blame Sony. If I remember well you are living in Vietnam, I have the phone everyday on my front pocket and drive scooter but my phone is still perfectly flat.
I do not put it on any too tide jean, and as soon as i sit completely on a car or chair I do remove it before sit. If not it is on a bag. So scare to break it, after all this phone is so thin and have so large and thin glass on it. I had to change iPhone glass of people siting on there sofa, same thing can happen here.
Sent from my C6802 using Tapatalk 4
Imdking said:
I do set the phone on the table too. I believe I twisted it sitting in the car from the house to the restaurant. It was a short drive; 2 blocks. So I didn't think much of it.
Click to expand...
Click to collapse
BINGO. This was my only concern regarding the Ultra from day one. I even wrote about it hear. I don't think you are the first to do this and you wont be the last either. Point is how do you know the integrity of the water resistance has not now been comprised? You don't!
I love the Ultra BUT putting that beast in a pocket was simply asking for eventual trouble. As you wrote how could an aluminium frame that dimension prevent twisting?
Sorry you had to experience this.
Regards.
---------- Post added at 02:26 PM ---------- Previous post was at 02:16 PM ----------
encryptioncsta said:
post a youtube video or pics to let us see, as this is sorta scary and might become usual as if this happens to more than yourself at least we can all tell sony support its a common fault
Click to expand...
Click to collapse
With great respect to you Sir this is not a Sony 'problem'. THE 'problem' with the Ultra is portability. Woman can use hand bags men will try and use trousers. The Ultra is simply to large for general trouser use. Add to this the materials used, glass, plastics and Aluminium and what can we expect? Even titanium at that thinness will eventually flex. This, to me, is a classic example of a device defeating its own purpose.
I love the Ultra I love my Z and 10.1 Z tablet. I have gone back to the plastic smaller world of the new Note 3 as I know I just could not live with the portability problems with the beautiful Ultra.
There are only two tragedies in life. One is NOT having what we want the other is having it.
This will solve itself as long as you live in a temperate climate with seasonal change. What i'm trying to say is: Winter is coming, and we will use jackets/coats which will make our lives much simpler. To the people of SE Asia, Africa, Australia, Southern Europe and Southern USA, i'm very sorry
Imdking said:
Guys...
I've had my C6802 for a week now. I've been loving it, and I didn't understand why people are dissing it about pocket ability. It fits in my pants pocket just fine. I just make sure that the left front pocket is reserved for the phone alone, no keys, change, or any other scratcher. Breast pocket is just disaster waiting to happen - button down flap can't even come over the phone. So that's out.
Today I sat down at the restaurant to use the Wi-Fi on my laptop, and I hooked up the XZU to download a movie through Media Go. I noticed the phone rocking back and forth diagonally, not laying flat on the table top. I thought maybe the table is sloping on that side. So, I moved the phone to another spot; same thing. I picked up the phone and eyeballed it along its profile! Alas! It was bent!
I remembered...... Aluminum frame..... so I flexed it diagonally to fix it, and it straightened out!
So be warned folks! Even if it fits in your pocket, sitting down with the phone in the pocket will definitely bend it! This might even lead to the glass corners popping out!
Click to expand...
Click to collapse
I personally keep it in my jacket pocket or in the jeans pocket, and sometimes they are really tight, and 80% of the time the ZU pops out a few inches from them, but my phone is still perfect.
On the other hand I think that aluminum bending on this device would be so limited that you can't even find out: phone is resting (face or back) on glass.
In no part the aluminum touches the table.
And even if you do manage to bend your device, I think it would have been much more than keeping it in a pocket. It would be all misaligned from angle to angle, at the point that the glass would break for the force pressing every time you lay it flat or you use it.
I wouldn't mind seeing pics too before saying any more things.
Sent from my C6833 using Tapatalk 2
Guys, any phone will do this. I am sorry that the OP experienced damage, but if anything it's the fault of the larger dimensions of the phone, not its thinness. Think about it: what constitutes the vast majority of a phone's thickness? It's the internal volume, obviously. It's the internal volume that was reduced in order to make the phone thin, not the thickness of the frame or glass sheets. Those would be the same regardless of how thick or thin the phone as, as they're just "caps." The fact that the phone is longer and wider than usual will allow you to exert more torque on the frame because of leverage, but the frame itself is no weaker than any other phone, and probably stronger than many.
Just put a lanyard on it and hang it on your neck...
Worry about it being stolen while hanging infront of your chest? Then place it under your shirt!
Problem solved..
"Sent from my refrigerator"
capitansid said:
Just put a lanyard on it and hang it on your neck...
Worry about it being stolen while hanging infront of your chest? Then place it under your shirt!
Problem solved..
"Sent from my refrigerator"
Click to expand...
Click to collapse
If you're into torture and breaking your own neck, sure why not
Sent from my Z Ultra, using XDA Premium 4
This is phenomena only experienced goons who wear skinny jeans...smh...
bASKOU said:
Even if someone of 40 kg would sit on it while on the rear pocket I would not blame Sony. If I remember well you are living in Vietnam, I have the phone everyday on my front pocket and drive scooter but my phone is still perfectly flat.
t from my C6802 using Tapatalk 4
Click to expand...
Click to collapse
Yeah, I am very careful about pick-pocketers in Hanoi, so I try not to put it in my back pocket anyway
It fits my front pocket fine, but I find it a bit hard to get it out while riding my bike, find it harder to answer it one-handed, and even more difficult to put it back into the front pocket while riding the bike. Depending on other things I have in front pocket, I have to stand on my bike while riding to put it back into the pocket.
(for those of you who don't know Vietnam, it must sound crazy )
Can't wait until winter so that I can use my inside jacket pocket.
And back to topic, I agree with most posts so far.
It is about portability problem, not design or manu quality problem. Applying torque on something so wide, long and thin must be avoided.
MY HUNT FOR THE PERFECT MAN-BAG NEEDS TO BE STEPPED UP A GEAR.
Guys.
There is nothing wrong with the phone. Nothing wrong with the build quality, or the frame, construction... none of that!
The phone fits in pants pocket. I use the front pocket. If you do carry it in your front pants pocket, be aware that sitting down with the phone in your front pocket will place torque on the phone, twisting it. My phone was NOT twisted enough to even consider it damaged. I just noticed that it wasn't perfectly flat when I placed it on the table. I twisted it back and corrected it.
After that little incident, I now make sure that I take it out of my pocket when I get in the car, or sit down. So, guys, becareful.
I have been using this gear keeper. The retention force is a bit strong, but very solid. I also have a larger sunglasses cloth bag to keep it protected till a case arrives. The MW600 works well for bluetooth call access/audio while the phone is tucked away. I listen to internet news while riding a motorcycle.
Gear Keeper RT4-5272 Deluxe Instrument/Gear Tether 3 Mounting Options (Snap/Velcro/Stud) with 3 Q/C Split Ring and Lanyard Accessories
amazon.com/RT4-5272-Instrument-Mounting-Options-Accessories/dp/B00A36SD96/ref=sr_1_2?ie=UTF8&qid=1380119641&sr=8-2&keywords=gear+keeper
Retractable Tether for Camera's / Range finders / Dog Transmitters / GPS units / FRS Radio's
255 grams Retraction Force 80cm Extension 27 kg break/release
3 Mounting Options Included-Snap Clip / Velcro Strap / Threaded Stud
Quick Connect Gear Attachment System includes Q/C Split Ring and 2 Q/C Lanyards
Combo Mount and added accessories allows for the ultimate in versatility
jewelkobayashi said:
Yeah, I am very careful about pick-pocketers in Hanoi, so I try not to put it in my back pocket anyway
It fits my front pocket fine, but I find it a bit hard to get it out while riding my bike, find it harder to answer it one-handed, and even more difficult to put it back into the front pocket while riding the bike. Depending on other things I have in front pocket, I have to stand on my bike while riding to put it back into the pocket.
(for those of you who don't know Vietnam, it must sound crazy )
Can't wait until winter so that I can use my inside jacket pocket.
And back to topic, I agree with most posts so far.
It is about portability problem, not design or manu quality problem. Applying torque on something so wide, long and thin must be avoided.
MY HUNT FOR THE PERFECT MAN-BAG NEEDS TO BE STEPPED UP A GEAR.
Click to expand...
Click to collapse
mrgardiner said:
I have been using this gear keeper. The retention force is a bit strong, but very solid. I also have a larger sunglasses cloth bag to keep it protected till a case arrives. The MW600 works well for bluetooth call access/audio while the phone is tucked away. I listen to internet news while riding a motorcycle.
Click to expand...
Click to collapse
Interesting indeed. Your reply would have been just as fitting in the post I opened under accessories section about how people carry their ZU :good:
Do you keep the phone dangling on you, or into a pocket while it is like it's on a lanyard and pull it when needed, or do you attach it to a bag of some kind and keep it in there??
I can see it being used in a million different ways... How do you use it?
Imdking said:
Guys...
I've had my C6802 for a week now. I've been loving it, and I didn't understand why people are dissing it about pocket ability. It fits in my pants pocket just fine. I just make sure that the left front pocket is reserved for the phone alone, no keys, change, or any other scratcher. Breast pocket is just disaster waiting to happen - button down flap can't even come over the phone. So that's out.
Today I sat down at the restaurant to use the Wi-Fi on my laptop, and I hooked up the XZU to download a movie through Media Go. I noticed the phone rocking back and forth diagonally, not laying flat on the table top. I thought maybe the table is sloping on that side. So, I moved the phone to another spot; same thing. I picked up the phone and eyeballed it along its profile! Alas! It was bent!
I remembered...... Aluminum frame..... so I flexed it diagonally to fix it, and it straightened out!
So be warned folks! Even if it fits in your pocket, sitting down with the phone in the pocket will definitely bend it! This might even lead to the glass corners popping out!
Click to expand...
Click to collapse
Just two things.
One: it's the 29th, you posted on 23rd.
Two: several people asked you for pics, and you posted none. If you had time to open a topic about it, you sure have some to take 2 simple pics to prove what you're saying.
That said, until you do post some pictures, I call BS on the whole "the ZU bends if kept in pockets" argument.
Sent from my C6833 using Tapatalk 2
fastest83 said:
Just two things.
One: it's the 29th, you posted on 23rd.
Two: several people asked you for pics, and you posted none. If you had time to open a topic about it, you sure have some to take 2 simple pics to prove what you're saying.
That said, until you do post some pictures, I call BS on the whole "the ZU bends if kept in pockets" argument.
Sent from my C6833 using Tapatalk 2
Click to expand...
Click to collapse
Pictures of what? My twisted phone? I am not twisting my phone again just to provide you with pictures.
My phone got twisted, I corrected it, and I advised other pocketers to be careful. There's no evidence to be had. You obviously read only my original post, and omitted the one on page 2.
I use it for safety mostly. If I am at work the phone stays in my pocket(front or back) while attached. When sitting down it might rest in my lap depending on the meeting or I unsnap(the clip mechanism is really-too stiff) it and set it on the table or my desk. I might leave it dangling when tieing my shoes.
I had it in a jeans pocket while riding a motorcycle for less than a mile., and I have <1/2 millimeter play or travel on a flat table. Lanyard to front camera diagonal is fine, but headphone jack to opposite corner wiggles a little. I haven't tried unbending it. I could try to take a photo, but there likely wouldn't be much to see.
Sent from my C6833 using xda app-developers app
This is really easy to make.
The raw materials are:
aluminum flatbar
3m automotive mounting tape
electrical tape
plastic cabinet support
I am not positive about that last item. I believe it is a drawer or cabinet fastener of some kind. I have no idea what it came with. It was just something I found in my junk drawer.
I trimmed it down, sanded the edge. Then I cut a piece of aluminum flatbar to about 4". I bent it about 30 degrees or so. Used the 3m tape to mount the flatbar to the back of the controller, and the plastic channel to the flatbar. Then I wrapped it in electrical tape to make it black. Kinda ghetto, but I don't like painting. The thickness of the channel just happened to be perfect for holding the Shield when it's in the Fintie case.
Yes, it's a little on the heavy side. You won't want to marathon game this way. But it works. There's really no other way for me to prop the tablet up on my lap when I am sitting on the couch or in bed.
Anyway, just wanted to share the idea with ya.
Amazon link to the Fintie case: http://www.amazon.com/Fintie-NVIDIA...Smart+Shell+Case+Cover+For+2014+NVIDIA+Shield
btw, I think it would be much less unwieldy if the channel was right on top of the controller. Unfortunately, that would prevent access to the charging port. I might get a 3" OTG cable with a right angle connector that can stay there permanently, then shove the channel as close to the controller as possible.
Nice work mate
holy ****... i didn't believe it would be possible but nice job man LOL
How long can you hold it for before your arms need a break? That's the only thing I'm thinking off when I see that.
CharlieBoy808 said:
holy ****... i didn't believe it would be possible but nice job man LOL
How long can you hold it for before your arms need a break? That's the only thing I'm thinking off when I see that.
Click to expand...
Click to collapse
It's a little on the heavy side for sure. I had it resting in my lap.
I actually just sent my tablet back today. With the screen off, it went from 82% battery to dead in just a couple hours. Plus the flaky wifi I was getting, I got tired of messing with it. So if anyone wants the mount, let me know.
shapeways.com/model/2843532/nvidia-shield-tablet-and-controller.html?materialId=25