This small guide was succesfull for me. Hope this will help you guys!
For L09C432B360
1. Install Firmware Finder
2. Enter in Firmware Finder Settings and select Install via system update.
3. You'll get prompt to Download FF Proxy, select Download Addon.
4. Install FF Proxy and dont run
5. Go back to FF and select GET FIRMWARE LIST
6. Select VIE-L09C432B360 Size: 1.334
7. Select SEND FIRMWARE TO UPDATER
8. FF Proxy now will start
9. Go to Wireless and set proxy to: localhost with 8080 port
10. Go to system settings and chose Updater
11. You'll get VIE-L09C432B360 available -> DONT CLICK TO UPDATE/DOWNLOAD
12. Go to wireless settings and disable proxy ( set it to none)
13. Go back to updater and chose Download latest full package
14. Update and VOILA!
GOOD LUCK
That is exactly what I did few days ago and work just fine for me. Now am on android N and Emiui 5
The same, upgrade successfull now, I discover this new EMUI
zubyro said:
This small guide was succesfull for me. Hope this will help you guys!
For L09C432B360
1. Install Firmware Finder
2. Enter in Firmware Finder Settings and select Install via system update.
3. You'll get prompt to Download FF Proxy, select Download Addon.
4. Install FF Proxy and dont run
5. Go back to FF and select GET FIRMWARE LIST
6. Select VIE-L09C432B360 Size: 1.334
7. Select SEND FIRMWARE TO UPDATER
8. FF Proxy now will start
9. Go to Wireless and set proxy to: localhost with 8080 port
10. Go to system settings and chose Updater
11. You'll get VIE-L09C432B360 available -> DONT CLICK TO UPDATE/DOWNLOAD
12. Go to wireless settings and disable proxy ( set it to none)
13. Go back to updater and chose Download latest full package
14. Update and VOILA!
GOOD LUCK
Click to expand...
Click to collapse
Where wireless ?Your mean WiFi?
Step 4.5 switch on again Install via System Update, my went to off again after I installed the FF Proxy program in step 4
regards mb
Hey ! I got an issue...
During the update in "Updater" app, when its on 74%, Updater close the process and restart from 60%, i wait 74%.. the same. It's a loop.
What can i do ? Sorry for my bad english, and thank you!
EDIT: ok problem solved, i used the proxy during the download and it worked. My emui5 works but i have not Huawei ID app, theme store doesn't work and if i reboot i got an error "You device has failed verification code and may work not properly". What can i do? Thanks a lot for your support !
[SOLVED: installed b181 rollback and retry with CORRECT INSTRUCTION via firmware finder]
Same thing.. totally unhappy. Read my previous comment about camera. The aperture mode is not working properly anymore. Some other things, too.. battery just draining on my.. almost as worse as iPhone. I don't see any advantages.. does anyone?
I find everything unclear. Specially the drop down push messages.. Will def. Roll back
Mine simply won´t update. Fails on 5% on update. Tried to reset the phone. Download eRecovery. It wont do nothing.. Everything fails.
Do i need to unlock the Bootloader?
Same problem...74% loop&restart from 61%.....How we can solve this problem?
Just wanted to say cheers for the guide. Managed to update my vodafone uk branded to 7. Make sure when your searching for your new firmware that you do it on your 4g not wifi. Then switch to your wifi to download
Hmmmm. Updated my O2 P9+ fine to C40B330, all looking good - although the battery drain seems high, been hitting my 20% notification two days in a row and never normally see it.
Anyway, went to use Android Pay and I get an error that it can't be used as it can't verify my version of Android. Tried uninstalling and reinstalling. cleared cache, cleared data.
I'm not rooted, didn't unlock the bootloader, just followed the instructions above. Any ideas? Had a search of the forum, there's lots of tips for Oneplus owners but nothing much for Huawei.
Just checked and B332 has been released... I'll flash that and see if it's any better at either battery life or Android Pay!
Trouble is, now I've sampled Nougat I can't go back to MM So I looked at my upgrade options.... I can pay off my P9+ and get a P10 for £60 and an extra £5 a month.... Hmm......
Hello,
I'm with VIE-L09 and i'm already on C432B320 but i want to re-flash so this method don't work anymore, how to re-flash safe without root?
Found b370 in FF (now i have b360) for c432 and tried to send via Ff proxy
Ota version (224mb on FF...640 mb on Huawei updater )
System reboot but Ask only for reboot / wipe
Tried also full update but no luck
Yes, tried dload/recovery method too, didn't work just says "update package doesn't exist" ...
---------- Post added at 07:55 AM ---------- Previous post was at 07:24 AM ----------
I managed to install it via servicemenu, *#*#2846579#*#* , what I did wrong before is I extracted the update into dload which resulted in a subfolder called update. I moved the contents of "update" to directly under dload and the update worked. I got new kernel and new security patch, but it still displays B360. Strange. Seems to work well though.
Edit. I used the "full" package from 170321 in FF.
xeizo said:
Yes, tried dload/recovery method too, didn't work just says "update package doesn't exist" ...
---------- Post added at 07:55 AM ---------- Previous post was at 07:24 AM ----------
I managed to install it via servicemenu, *#*#2846579#*#* , what I did wrong before is I extracted the update into dload which resulted in a subfolder called update. I moved the contents of "update" to directly under dload and the update worked. I got new kernel and new security patch, but it still displays B360. Strange. Seems to work well though.
Edit. I used the "full" package from 170321 in FF.
Click to expand...
Click to collapse
Download also the hw specsea package so that you would go to b370
I did already download and extract update_data_full_hw_eu.zip and put in the same dload folder but obviously it didn't work. So where do I put those files? Or is there yet another package I need?
---------- Post added at 10:39 AM ---------- Previous post was at 10:14 AM ----------
xeizo said:
I did already download and extract update_data_full_hw_eu.zip and put in the same dload folder but obviously it didn't work. So where do I put those files? Or is there yet another package I need?
Click to expand...
Click to collapse
I answer myself, I overwrote the update-content in the dload folder with the update_data_... content and installed again. Now it's B370. Looks like it's a two stage process, rather clumsy, any way to install everything in just one large swoop?
xeizo said:
I did already download and extract update_data_full_hw_eu.zip and put in the same dload folder but obviously it didn't work. So where do I put those files? Or is there yet another package I need?
---------- Post added at 10:39 AM ---------- Previous post was at 10:14 AM ----------
I answer myself, I overwrote the update-content in the dload folder with the update_data_... content and installed again. Now it's B370. Looks like it's a two stage process, rather clumsy, any way to install everything in just one large swoop?
Click to expand...
Click to collapse
Yes its two step process because the cust is in the second update package..
xeizo said:
I did already download and extract update_data_full_hw_eu.zip and put in the same dload folder but obviously it didn't work. So where do I put those files? Or is there yet another package I need?
---------- Post added at 10:39 AM ---------- Previous post was at 10:14 AM ----------
I answer myself, I overwrote the update-content in the dload folder with the update_data_... content and installed again. Now it's B370. Looks like it's a two stage process, rather clumsy, any way to install everything in just one large swoop?
Click to expand...
Click to collapse
I tried to install the update.app file extracted from update_full_hw_eu.zip in my external sdcard with the dload folder method, but when I reboot the phone, I get an error that stops the upgrade process immediately, at 5%....
Someone could post a direct link to the right update_full_hw_eu.zip file ?
Thanks for the attention
use b370 21.03 firmware and also his update_full_hw_eu.zip file (NOT 13.04 version)
(usa la versione del 21.03 e il suo update_full
Prima installi l'update 21.03 poi dopo il file update, sempre via dload)
Related
Hi, guys,
Yesterday, Huawei released Android 4.0 ICS DEMO for U8860(a.k.a. Huawei Honor), as always I applied this updated immediately. It works fine, although I didn't see much difference from Android 2.3.
Here is a question, Does anybody know how to root U8860 with Android 4.0 safely?
big thanks.
!
I am also new owner from huawei honor..best phone ever ! battery life extremely good ! my phone is on 2.3.5 arriwed and don't need to upgrade it immediately.
does anybody know how to root this phone ?
Thanx
hi,mirot
You may try the way in which people root huawei u8800
prettyyy said:
Hi, guys,
Yesterday, Huawei released Android 4.0 ICS DEMO for U8860(a.k.a. Huawei Honor), as always I applied this updated immediately. It works fine, although I didn't see much difference from Android 2.3.
Here is a question, Does anybody know how to root U8860 with Android 4.0 safely?
big thanks.
Click to expand...
Click to collapse
did you download the .zip file to upgrade to ICS?
!
unzip the file and copy to sdcard.make update manually on the phone
mirot said:
unzip the file and copy to sdcard.make update manually on the phone
Click to expand...
Click to collapse
all the links i came across to upgrade to ICS are all 'UPDATE.APP', no zip files.
Huawei doesnt have it on their site anymore. I was hoping you could mirror it or something.
BTW i tried rooting using the method for the U8800, does not work.
hello, we got Root, I can not insert a link (no rights), copy the post:
1. Set the wood on your computer.
2. We enter the engineering menu of the body. (*#*# 2,846,579 #*#*) further ProjectMenu - Background setting-Log setting - Logswitch - LOG on - turn on, return to the ProjectMenu - Damp & Log include all items (total 4 points). Exit and restart ProjectMenu of the body.
3. Connecting to a PC the "Settings" - "Applications" - "Unknown sources" - turn on, then "Quick" - disable, then "Development" - include "Debug on USB" and "left on"
4. On the PC, disable antivirus, run SuperOneClickv2.3.1. and in the upper left corner click "ROOT".
5. On the pop-up windows give the "OK", a window with a proposal where a register just turn it off.
6. The ending of the whole operation will be a few lines (about half the screen) at the end of the last word "OK"
7. Turn off SuperOneClickv2.3.1, then "Options" - "Applications" - "Development" - turn off the "Debug on USB" and "left on" turn on "Quick", disconnected from the PC, restart the body.
8. If done correctly then open desks and one of them will see the icon "Sueruser" versiya3.0.7.
9. Return to its original condition and value of LOG on Damp & Log
PS
A small addition to the previous post, namely, after the root note two folders on the SD card and bugreports sleeplog. Remove the contents. If they continue to be replenished, then go to step 2 do the engineering menu, and then claim 9. Restart the body, clean folder on your SD card.
!
mistic-tooth said:
hello, we got Root, I can not insert a link (no rights), copy the post:
1. Set the wood on your computer.
2. We enter the engineering menu of the body. (*#*# 2,846,579 #*#*) further ProjectMenu - Background setting-Log setting - Logswitch - LOG on - turn on, return to the ProjectMenu - Damp & Log include all items (total 4 points). Exit and restart ProjectMenu of the body.
3. Connecting to a PC the "Settings" - "Applications" - "Unknown sources" - turn on, then "Quick" - disable, then "Development" - include "Debug on USB" and "left on"
4. On the PC, disable antivirus, run SuperOneClickv2.3.1. and in the upper left corner click "ROOT".
5. On the pop-up windows give the "OK", a window with a proposal where a register just turn it off.
6. The ending of the whole operation will be a few lines (about half the screen) at the end of the last word "OK"
7. Turn off SuperOneClickv2.3.1, then "Options" - "Applications" - "Development" - turn off the "Debug on USB" and "left on" turn on "Quick", disconnected from the PC, restart the body.
8. If done correctly then open desks and one of them will see the icon "Sueruser" versiya3.0.7.
9. Return to its original condition and value of LOG on Damp & Log
PS
A small addition to the previous post, namely, after the root note two folders on the SD card and bugreports sleeplog. Remove the contents. If they continue to be replenished, then go to step 2 do the engineering menu, and then claim 9. Restart the body, clean folder on your SD card.
Click to expand...
Click to collapse
this is method only for 2.3.5 gingerbread and doesn't work with ICS !
but if you have bugreport in the phone also doesn't work on 2.3.5 gingerbread
i have also bugreport and cannot root the phone anymore ! sd card formated,also phone memory and bugreport is still inside !
---------- Post added at 01:30 PM ---------- Previous post was at 12:31 PM ----------
somebody have 2.3.5 rom for Honor with android market and gmail inside?please post link here
thanx
!
yeahhh,everything solved ! honor the best
mirot said:
somebody have 2.3.5 rom for Honor with android market and gmail inside?please post link here
thanx
Click to expand...
Click to collapse
Yea I think I my have found one..... Waiting for it to finish downloading if its the one we both seek I will post a link.
EDIT: trying this one now -
1.)Download the bootloader menu tool - recovery-v8.img 5.5 MB megauploadDOTcom/?d=GN3NFEWS
2.)Download this zip 2.3.6 Sorry I can't post links in my first few posts apparently. pm me will email link then someone with more posts can post link.
3.)Turn phone off, Hold down both the volume up AND the volume down keys without letting go also then press and hold the power button. After a while your whole screen should go PINK. your usb cable should already be plugged in and this should mount a usb drive on your computer that you can access. Open it. There will be a file in there called recovery.img , rename it to recovery.old, then copy the recovery-v8.img to this drive. Rename it to recovery.img. Pull out the battery and re-insert.
Boot the phone by pressing and holding only the volume up key and the power button. This should load you into the new recovery image. From here you can load the .zip file from the menu.
Phew.
Its good to have a working phone.
PS its a custom rom thats already rooted and has root explorer installed. NICE! Oh ad you can install google apps from google. just google gapps-ics-20111125-2.zip
n3mz1z said:
Yea I think I my have found one..... Waiting for it to finish downloading if its the one we both seek I will post a link.
EDIT: trying this one now -
1.)Download the bootloader menu tool - recovery-v8.img 5.5 MB megauploadDOTcom/?d=GN3NFEWS
2.)Download this zip 2.3.6 Sorry I can't post links in my first few posts apparently. pm me will email link then someone with more posts can post link.
3.)Turn phone off, Hold down both the volume up AND the volume down keys without letting go also then press and hold the power button. After a while your whole screen should go PINK. your usb cable should already be plugged in and this should mount a usb drive on your computer that you can access. Open it. There will be a file in there called recovery.img , rename it to recovery.old, then copy the recovery-v8.img to this drive. Rename it to recovery.img. Pull out the battery and re-insert.
Boot the phone by pressing and holding only the volume up key and the power button. This should load you into the new recovery image. From here you can load the .zip file from the menu.
Phew.
Its good to have a working phone.
PS its a custom rom thats already rooted and has root explorer installed. NICE! Oh ad you can install google apps from google. just google gapps-ics-20111125-2.zip
Click to expand...
Click to collapse
please PM me those link
i am eager to get my self a rooted ROM.
many thanks pal
n3mz1z said:
Yea I think I my have found one..... Waiting for it to finish downloading if its the one we both seek I will post a link.
EDIT: trying this one now -
1.)Download the bootloader menu tool - recovery-v8.img 5.5 MB megauploadDOTcom/?d=GN3NFEWS
2.)Download this zip 2.3.6 Sorry I can't post links in my first few posts apparently. pm me will email link then someone with more posts can post link.
3.)Turn phone off, Hold down both the volume up AND the volume down keys without letting go also then press and hold the power button. After a while your whole screen should go PINK. your usb cable should already be plugged in and this should mount a usb drive on your computer that you can access. Open it. There will be a file in there called recovery.img , rename it to recovery.old, then copy the recovery-v8.img to this drive. Rename it to recovery.img. Pull out the battery and re-insert.
Boot the phone by pressing and holding only the volume up key and the power button. This should load you into the new recovery image. From here you can load the .zip file from the menu.
Phew.
Its good to have a working phone.
PS its a custom rom thats already rooted and has root explorer installed. NICE! Oh ad you can install google apps from google. just google gapps-ics-20111125-2.zip
Click to expand...
Click to collapse
why when i connect phone to the pc after pink screen my sdcard and phone cant detect in the pc??
what i should do to be detected? and send me link ofcourse.. thxs
update:
i have succeed go into recovery mode but i cant install the zip file.. what i must load the ROM into sd card before?
!
If you have 2.3.6 firmware your phone will be NOT recognized on your PC by pink screen !!! By reason of lock on 2.3.6.
You can install Chinacom 2.3.5 firmware and use this procedure(pink screen) again,and will be OK.after that you can install any custom rom also 2.3.6 !
mirot said:
If you have 2.3.6 firmware your phone will be NOT recognized on your PC by pink screen !!! By reason of lock on 2.3.6.
You can install Chinacom 2.3.5 firmware and use this procedure(pink screen) again,and will be OK.after that you can install any custom rom also 2.3.6 !
Click to expand...
Click to collapse
ohh.. that's why i cant connect to the pc because i use 2.3.6 thxs for your information
anyone have link ginger 2.3.6 with market and gmail work? please give me link i need it immediately
!
here : multi language and with gmail and market enabled ! but not rootable !
http://depositfiles.com/files/zwb2nscyu
regards
Root Hauwei U8860 with ICS and Gapps
So I gave up on Gingerbread. I am now running ICS with Gapps.
I did it by the following steps.
1.) install the ICS demo provided by huawei
2.) Replace the recovery.img with the v8 one via the pink screen method mentioned in my previous post.
3.) download the gapps ics .zip to your sdcard and rename it to update.zip in the root of sdcard.
4.) Boot to recovery menu by holding power button and volume up button, then slect update zip, then chose the update.zip. once completed reboot.
5.) when you boot into ics login to google talk with your account first via 3g data not wifi data. then gmail.
6.) now market should work!
Also you can root ICS easy with any rooting tools. I used RootThat-v1.0.0
PS I emailed/pm'd the gingerbread rom to all who requested it. I found it unstable though.
!
no bro.newest version of ICS for Honor is with kernel 3.0.8 ! is pretty good but still not stable and on testing.it is rootable also with oneclickroot not only over pink screen.link what i give you that is very stable version of 2.3.6 but not rootable if you have "bugreport" inside phone,if not it is possible to root
regards
any ICS ROM's link? i found it very difficult on google
is this ICS build already stable on this phone?
n3mz1z said:
So I gave up on Gingerbread. I am now running ICS with Gapps.
I did it by the following steps.
1.) install the ICS demo provided by huawei
2.) Replace the recovery.img with the v8 one via the pink screen method mentioned in my previous post.
3.) download the gapps ics .zip to your sdcard and rename it to update.zip in the root of sdcard.
4.) Boot to recovery menu by holding power button and volume up button, then slect update zip, then chose the update.zip. once completed reboot.
5.) when you boot into ics login to google talk with your account first via 3g data not wifi data. then gmail.
6.) now market should work!
Also you can root ICS easy with any rooting tools. I used RootThat-v1.0.0
PS I emailed/pm'd the gingerbread rom to all who requested it. I found it unstable though.
Click to expand...
Click to collapse
are you already fix the camera flash, radio fm, and any bugs in ICS?
btw huawei already upload ginger new version ini international language so u can grab it ginger with gapps work tinyurl..com/77hurt3 (add the http and erase dot)
I bought a Mediapad X1 from China via AliExpress.
I cannot make anything from a limited Chinese ROM.
Anybody who has international ROM or can extract it from the international version, please help!
satawat.thongsawat said:
I bought a Mediapad X1 from China via AliExpress.
I cannot make anything from a limited Chinese ROM.
Anybody who has international ROM or can extract it from the international version, please help!
Click to expand...
Click to collapse
The international version hasn't been released yet... I bought mine (4G version) through Lenteen from Hong-Kong, and everythings works fine ! I installed google apps, rooted my phone
I know that Huawei was supposed to release it at the end of may in France but any news nowhere on the web... none even from Huawei themself !
So we just have to wait and see...
gregou said:
The international version hasn't been released yet... I bought mine (4G version) through Lenteen from Hong-Kong, and everythings works fine ! I installed google apps, rooted my phone
I know that Huawei was supposed to release it at the end of may in France but any news nowhere on the web... none even from Huawei themself !
So we just have to wait and see...
Click to expand...
Click to collapse
Does it sync your Google contacts correctly? If so, what did you need to do to get that working?
gregou said:
The international version hasn't been released yet... I bought mine (4G version) through Lenteen from Hong-Kong, and everythings works fine ! I installed google apps, rooted my phone
I know that Huawei was supposed to release it at the end of may in France but any news nowhere on the web... none even from Huawei themself !
So we just have to wait and see...
Click to expand...
Click to collapse
Thank you for the reply, some questions:
1. So, yours is also a Chinese version?
2. Please post the link for rooting.
3. After rooting, install the GApp, version for 4.2.2? And then we can go for anything, like Nova launcher?
satawat.thongsawat said:
Thank you for the reply, some questions:
1. So, yours is also a Chinese version?
2. Please post the link for rooting.
3. After rooting, install the GApp, version for 4.2.2? And then we can go for anything, like Nova launcher?
Click to expand...
Click to collapse
So yes it's also a chinese version, but it's the 4G chinese version.
TUTO FOR ROOTING :
Here is the procedure for your rooter Huawei Mediapad X1/Honor X1:
Here's what you need:
MediaPad Huawei X1
A micro USB to USB cable
PC
Root Genius software at the following address : http://www.shuame.com/en/root/
Now to root your device : (This method works with B002 Chinese version, not tested on others number firmwares)
1 - Enable developer mode on Huawei MediaPad X1 in Settings> About phone
Press several times on the box " build number " until a message announcing the activation of developer mode
Connect your Huawei MediaPad X1.
2 - In the notification bar choose the Hi Suite mode and let the PC detected the device
3 - Start the Root Genius you previously downloaded, it will automatically detect your device, it only remains for you to click on the ROOT button and wait
4 - If all went well , you should have a message of congratulations . In addition, a new application called King User will be installed on your device.
Now you can use apps that require root such as Titanium Backup , Root Explorer, etc. . You 'll also be able to uninstall applications or games you do not want and which are pre-installed on the device.
If you have any questions do not hesitate!
P.S : If anything goes wrong that's your entire responsability !
---------- Post added at 05:22 AM ---------- Previous post was at 05:15 AM ----------
TUTO TO GET ALL GAPPS (INCLUDED CONTACTS SYNC)
As you know , the Chinese version of the Huawei Mediapad do not get Google applications .
*
Here is the procedure to have them all , including the synchronization of contacts !
*
*What you need:
Huawei Mediapad Honor X1 (chinese version) Your phone must be already rooted ! ( follow the tutorial i posted earlier)
A file explorer that supports the administration ROOT rights (root explorer, es file explorer , etc. . ) Available on Google Play Store
There is nothing very complicated , just follow the tutorial :
Open your file explorer supporting the rights adminstration ROOT
Go to the following folder
/ cust / channel / charm_china_u / xml /
You will find the file UNSTALL_APK.XML
Rename it to : UNSTALL_APK.XML.OLD
This is done !
Restarting the Huawei Honor Mediapad/Honor X1 , applications will be automatically downloaded and installed on the phone and you will have access to all Google services including synchronization of contacts !
*
WARNING: by doing this manipulation, future updates will no longer be compatible with the device and you will have to rename the file UNSTALL_APK.XML.OLD to UNSTALL_APK.XML to update the device. Otherwise, you can make a copy of the original file that you can keep safe somewhere on your phone or computeur.
If anything goes wrong that's your entire responsability !
http://consumer.huawei.com/cn/mobile-phones/support/downloads/honour-x1-cn.htm
vyming said:
http://consumer.huawei.com/cn/mobile-phones/support/downloads/honour-x1-cn.htm
Click to expand...
Click to collapse
This is a Chinese ROM?
gregou said:
So yes it's also a chinese version, but it's the 4G chinese version.
TUTO FOR ROOTING :
Here is the procedure for your rooter Huawei Mediapad X1/Honor X1:
Here's what you need:
MediaPad Huawei X1
A micro USB to USB cable
PC
Root Genius software at the following address : http://www.shuame.com/en/root/
Now to root your device : (This method works with B002 Chinese version, not tested on others number firmwares)
1 - Enable developer mode on Huawei MediaPad X1 in Settings> About phone
Press several times on the box " build number " until a message announcing the activation of developer mode
Connect your Huawei MediaPad X1.
2 - In the notification bar choose the Hi Suite mode and let the PC detected the device
3 - Start the Root Genius you previously downloaded, it will automatically detect your device, it only remains for you to click on the ROOT button and wait
4 - If all went well , you should have a message of congratulations . In addition, a new application called King User will be installed on your device.
Now you can use apps that require root such as Titanium Backup , Root Explorer, etc. . You 'll also be able to uninstall applications or games you do not want and which are pre-installed on the device.
If you have any questions do not hesitate!
P.S : If anything goes wrong that's your entire responsability !
---------- Post added at 05:22 AM ---------- Previous post was at 05:15 AM ----------
TUTO TO GET ALL GAPPS (INCLUDED CONTACTS SYNC)
As you know , the Chinese version of the Huawei Mediapad do not get Google applications .
*
Here is the procedure to have them all , including the synchronization of contacts !
*
*What you need:
Huawei Mediapad Honor X1 (chinese version) Your phone must be already rooted ! ( follow the tutorial i posted earlier)
A file explorer that supports the administration ROOT rights (root explorer, es file explorer , etc. . ) Available on Google Play Store
There is nothing very complicated , just follow the tutorial :
Open your file explorer supporting the rights adminstration ROOT
Go to the following folder
/ cust / channel / charm_china_u / xml /
You will find the file UNSTALL_APK.XML
Rename it to : UNSTALL_APK.XML.OLD
This is done !
Restarting the Huawei Honor Mediapad/Honor X1 , applications will be automatically downloaded and installed on the phone and you will have access to all Google services including synchronization of contacts !
*
WARNING: by doing this manipulation, future updates will no longer be compatible with the device and you will have to rename the file UNSTALL_APK.XML.OLD to UNSTALL_APK.XML to update the device. Otherwise, you can make a copy of the original file that you can keep safe somewhere on your phone or computeur.
If anything goes wrong that's your entire responsability !
Click to expand...
Click to collapse
@gregou
I cannot get into download mode to install Gapps via odin.
Also cannot find recovery mode???
How to install Gapps,then??
satawat.thongsawat said:
@gregou
I cannot get into download mode to install Gapps via odin.
Also cannot find recovery mode???
How to install Gapps,then??
Click to expand...
Click to collapse
When the phone reboot, after you renamed the file, gapps are automatically installed by the phone.. You don't have to use recovery mode at all !!
And for now, i'm not sure that CWM is available for this model... I think i saw it on a chinese forum but when i translate it's too messy and i have to be registered on this forum to download it so... we have to wait that someone make a post here in english with th e CWM in download...
gregou said:
When the phone reboot, after you renamed the file, gapps are automatically installed by the phone.. You don't have to use recovery mode at all !!
And for now, i'm not sure that CWM is available for this model... I think i saw it on a chinese forum but when i translate it's too messy and i have to be registered on this forum to download it so... we have to wait that someone make a post here in english with th e CWM in download...
Click to expand...
Click to collapse
Okay, I see the point, we just install portions of Google apps we need, starting with play store, the any thing you need.
I do hope we'll have CWM, or at least hardware ways to boot into download and recovery mode.
The KitKat may be far from reality?
satawat.thongsawat said:
Okay, I see the point, we just install portions of Google apps we need, starting with play store, the any thing you need.
I do hope we'll have CWM, or at least hardware ways to boot into download and recovery mode.
The KitKat may be far from reality?
Click to expand...
Click to collapse
We'll get Kikat firmware on this phone for sure, we just have to wait from Huawei to rolling out this version.
It's not portions of google apps as when you do this procedure i explained, ALL the gapps are installed automatically on the phone.
Basically, Huawei made a script in the phone for not allowing these apps to be installed, but when you rename this file, the script is no longer available, then all the gapps are installing after the next reboot !
Mediapad X1 7D-503L
The only deference is the directory:
/ cust / channel / charm_china_l / xml / ( charm_china_l not charm_china_u)
and i use the command as su
mount -o rw,remount -t rootfs /cust
because when It try to rename the UNSTALL_APK.XML I take the error "Read-only file system"
thanks
X1 undetectable by the PC
I have GApps Syncing quite fine without rooting, except the contacts sync which is missing from the sync list. I see your steps are very straight forward, but unfortunately my X1 is not recognized by the PC, although I've installed HiSuite from Huawei website. I've also tried to install Huawei device driver for X1 from this site, but still unrecognized. Accordingly GeniusRoot is unable to detect and root my X1.
I'm Win 8.1 (both 32 and 64 bits), and I've tried to do all these procedures with Compatibility model for Win7, run as administrator, yet the X1 is till not detected by the PC.
Also USB Debugging is enabled in Developer Options.
Any idea what's the reason for this?
More info about my version:
Baseband: 21.529.00.00.000
Kernel: 3.0.8-01317-gcd83a45 [email protected] #1
Build Number: 7D-501uV100R001C233B013
gregou said:
So yes it's also a chinese version, but it's the 4G chinese version.
TUTO FOR ROOTING :
Here is the procedure for your rooter Huawei Mediapad X1/Honor X1:
Here's what you need:
MediaPad Huawei X1
A micro USB to USB cable
PC
Root Genius software at the following address :
Now to root your device : (This method works with B002 Chinese version, not tested on others number firmwares)
1 - Enable developer mode on Huawei MediaPad X1 in Settings> About phone
Press several times on the box " build number " until a message announcing the activation of developer mode
Connect your Huawei MediaPad X1.
2 - In the notification bar choose the Hi Suite mode and let the PC detected the device
3 - Start the Root Genius you previously downloaded, it will automatically detect your device, it only remains for you to click on the ROOT button and wait
4 - If all went well , you should have a message of congratulations . In addition, a new application called King User will be installed on your device.
Now you can use apps that require root such as Titanium Backup , Root Explorer, etc. . You 'll also be able to uninstall applications or games you do not want and which are pre-installed on the device.
If you have any questions do not hesitate!
P.S : If anything goes wrong that's your entire responsability !
---------- Post added at 05:22 AM ---------- Previous post was at 05:15 AM ----------
TUTO TO GET ALL GAPPS (INCLUDED CONTACTS SYNC)
As you know , the Chinese version of the Huawei Mediapad do not get Google applications .
*
Here is the procedure to have them all , including the synchronization of contacts !
*
*What you need:
Huawei Mediapad Honor X1 (chinese version) Your phone must be already rooted ! ( follow the tutorial i posted earlier)
A file explorer that supports the administration ROOT rights (root explorer, es file explorer , etc. . ) Available on Google Play Store
There is nothing very complicated , just follow the tutorial :
Open your file explorer supporting the rights adminstration ROOT
Go to the following folder
/ cust / channel / charm_china_u / xml /
You will find the file UNSTALL_APK.XML
Rename it to : UNSTALL_APK.XML.OLD
This is done !
Restarting the Huawei Honor Mediapad/Honor X1 , applications will be automatically downloaded and installed on the phone and you will have access to all Google services including synchronization of contacts !
*
WARNING: by doing this manipulation, future updates will no longer be compatible with the device and you will have to rename the file UNSTALL_APK.XML.OLD to UNSTALL_APK.XML to update the device. Otherwise, you can make a copy of the original file that you can keep safe somewhere on your phone or computeur.
If anything goes wrong that's your entire responsability !
Click to expand...
Click to collapse
Thanks for the awesome tutorial bro
I've managed to root the phone, installed es files explorer. Double checked with root checker and confirmed root
But I'm stuck with renaming the file...
And the folder have a slightly different name but that is the only folder I've got..
/cust/channel/charm_china_l/xml/ (yours is china_u)
So, everytime I rename the file it keeps on giving error task failed. I've checked in properties and it says readable:yes writable:yes
I can't delete the file as well the error says unstall_apk.xml cannot be deleted
can u help please
thanks in advance :good:
sordanny said:
Thanks for the awesome tutorial bro
I've managed to root the phone, installed es files explorer. Double checked with root checker and confirmed root
But I'm stuck with renaming the file...
And the folder have a slightly different name but that is the only folder I've got..
/cust/channel/charm_china_l/xml/ (yours is china_u)
So, everytime I rename the file it keeps on giving error task failed. I've checked in properties and it says readable:yes writable:yes
I can't delete the file as well the error says unstall_apk.xml cannot be deleted
can u help please
thanks in advance :good:
Click to expand...
Click to collapse
OK I managed to figure out the solution
Used Root File Manager to rename and voila!! Renamed the file, restart device and got all the Google stuff setup on the phone
Now there is this second problem which is a big pain in the arse
I can't add a second Google account on the phone to get all my contacts..........
Under settings -> accounts -> add account -- there is no option to select "Google" !!!!
Have anyone also face this problem and is there any solution??
Thanks in advance for the help
Guys, you do not need root or tricks to install Google stuff.
Open the Huawei app market. Search for Google. Click on the big Google banner at the top of the page. You get a dedicated page of Google stuff. There you have download links for play store, all the Google apps, and if you can figure out a little Chinese, calendar sync and contact sync software too.
ralphrmartin said:
Guys, you do not need root or tricks to install Google stuff.
Open the Huawei app market. Search for Google. You get a dedicated page of Google stuff. There you have download links for play store, all the Google apps, and if you can figure out a little Chinese, calendar sync and contact sync software too.
Click to expand...
Click to collapse
I can confirm this is true. I did a search for "gms" rather than Google - tap on the big link you get at the top of the results page, which takes you to a page of all the Google apps and services, and install everything! (You can always uninstall what you don't need later). No root required, and everything is syncing properly - calendar, contacts, tasks etc. Super easy.
ralphrmartin said:
Guys, you do not need root or tricks to install Google stuff.
Open the Huawei app market. Search for Google. Click on the big Google banner at the top of the page. You get a dedicated page of Google stuff. There you have download links for play store, all the Google apps, and if you can figure out a little Chinese, calendar sync and contact sync software too.
Click to expand...
Click to collapse
This worked for me too. I installed all google apps and everthing syncs except I still cant sync contacts or have more than one google account.
So frustrated
DannyBoy said:
This worked for me too. I installed all google apps and everthing syncs except I still cant sync contacts or have more than one google account.
So frustrated
Click to expand...
Click to collapse
Have you got Google Contacts Sync in your list of downloaded apps?
DannyBoy said:
This worked for me too. I installed all google apps and everthing syncs except I still cant sync contacts or have more than one google account.
So frustrated
Click to expand...
Click to collapse
Danny here's how to fix it, and u don't need root
if u have rooted and edited the unstall_apk.xml, best is download and flash the stock ROM first:
http://consumer.huawei.com/cn/support/downloads/detail/index.htm?id=20241 (click 立即下载 on the right)
u can also ignore it but all preinstalled google apps will become system apps, and if u've deleted some huawei bloatware u might not be able to OTA update latest B006 firmware
All the Google stuff can work perfectly even can add multiple Google accounts. Best thing is, u don't need root. Here's how:
1) Go to app centre - all - brand and look for the one with 谷歌 (sorry I've updated app centre and it might be different if u haven't update)
2) Download 联系人同步服务, 日历同步服务, Google Playstore, Gmail and Google plus. The rest can be downloaded from playstore
3) After install, open either playstore or gmail and sign in
At this stage, Google is already setup properly with contacts sync just it cannot add multiple Google accounts. Workaround:
4) Open Google plus. Settings - add account
And voila. The phone is perfect now
There's also an OTA update for the LTE version which updates your phone firmware to 7D-503LV100R001C233B006
Cool new features includes double tap screen on, some control over notification flash light for messages and background battery optimization :good:
Upgrade to Nougat for Huawei P9 Plus VIE-L09CO2 (Vodafone) is in place.
Good evening to the whole group. I am trying to download it through 'Firmware Finder',
but I would say to all those concerned, with the brand "Vodafone" which is output upgrade to Nougat with version VIE-L09C03B334. I hope that somewhere they can mettre the zipped file so it can be used with 'dload'.
Dear friends of the group to me I got the update successfully completed. As I said I used 'Firmware Finder', using the guidelines in the file that I enclose. hoping that you understand that since the re-translation has made Google Translation ', a post to a thread that is on the XDA forum. Good update to you.
Follow my instructions
- Make sure you are on VIE-L09C432B181
- Make sure the battery over 60%
- Now make a backup from your PC with HiSuite
- Now install the firmware Finder from the Play Store (link)
- Now go to Settings -> Advanced Settings -> Security -> Device Administration - >> NOW activate "Unknown sources"
- Now Open Firmware Finder and select the model (eg: VIE-L09C432)
- Now click on "GET FIRMWARE LIST"
- Now go to the Finder firmware settings and activate "Installing via system update"
- You will see a pop up "Huawei Firmware Proxy Finder" click "download ADDON"
- When the download is complete, install on your phone and open it
- Re open the finder firmware settings and check if "Installation using the updated" activated system, if you do not activate it for the 2nd time
- Now the firmware Finder and select the model as VIE-L09C432 (only if the model has this)
- Now click on "GET FIRMWARE LIST" and select first one where you see "VIE-L09C432B360" Date: 03/03/2017 TypeTA Size: 1.334GB
- If you selected "VIE-L09C432B360" Now you will see an option "Send Firmware Updater" click it
- Now it will automatically open a page "Firmware Finder Proxy"
- Now go to the Wi-Fi and connect to a Wi-Fi and Now "Network Edit" then "Show Advanced Options" Now select "Proxy" as "Manuel"
- In writing on the proxy host name: localhost
- In writing on the proxy port: 8080
- Now go to Settings -> System Update now, and click "Check for updates"
- Now you are going to see the name of an update "VIE-L09C432B360VIE-L09C432B360 -1,430,186,368.00 B" do not download this! this is not the right one!
- Back to System Update and you'll still get this the wrong update, do not worry, click on "MENU" and click on "Download the latest full package"
- You will now see the correct update "VIE-L09C432B360 2.39 GB" Now just click "hotfix"
- Do not download it, do not worry, just go to the Wi-Fi settings and disable "Proxy"
- Go back to the system upgrade and click pause and resume
- Wait until the end of the download, and after the phone will automatically install the update has been downloaded
If you have followed my instructions, it will be installed with B360 success.
Obviously you have to follow the signs quele for your version of firmware and that all root functions and how this suite if you had the miss and the directions that are on this forumo apply unfortunately for Andorid 6 'Marshmallow'.
Sorry for any typos or language.
Download fails at 74 %
Try´d this not working download fails at 74 %
Grlschia said:
Upgrade to Nougat for Huawei P9 Plus VIE-L09CO2 (Vodafone) is in place.
Good evening to the whole group. I am trying to download it through 'Firmware Finder',
but I would say to all those concerned, with the brand "Vodafone" which is output upgrade to Nougat with version VIE-L09C03B334. I hope that somewhere they can mettre the zipped file so it can be used with 'dload'.
Dear friends of the group to me I got the update successfully completed. As I said I used 'Firmware Finder', using the guidelines in the file that I enclose. hoping that you understand that since the re-translation has made Google Translation ', a post to a thread that is on the XDA forum. Good update to you.
Follow my instructions
- Make sure you are on VIE-L09C432B181
- Make sure the battery over 60%
- Now make a backup from your PC with HiSuite
- Now install the firmware Finder from the Play Store (link)
- Now go to Settings -> Advanced Settings -> Security -> Device Administration - >> NOW activate "Unknown sources"
- Now Open Firmware Finder and select the model (eg: VIE-L09C432)
- Now click on "GET FIRMWARE LIST"
- Now go to the Finder firmware settings and activate "Installing via system update"
- You will see a pop up "Huawei Firmware Proxy Finder" click "download ADDON"
- When the download is complete, install on your phone and open it
- Re open the finder firmware settings and check if "Installation using the updated" activated system, if you do not activate it for the 2nd time
- Now the firmware Finder and select the model as VIE-L09C432 (only if the model has this)
- Now click on "GET FIRMWARE LIST" and select first one where you see "VIE-L09C432B360" Date: 03/03/2017 TypeTA Size: 1.334GB
- If you selected "VIE-L09C432B360" Now you will see an option "Send Firmware Updater" click it
- Now it will automatically open a page "Firmware Finder Proxy"
- Now go to the Wi-Fi and connect to a Wi-Fi and Now "Network Edit" then "Show Advanced Options" Now select "Proxy" as "Manuel"
- In writing on the proxy host name: localhost
- In writing on the proxy port: 8080
- Now go to Settings -> System Update now, and click "Check for updates"
- Now you are going to see the name of an update "VIE-L09C432B360VIE-L09C432B360 -1,430,186,368.00 B" do not download this! this is not the right one!
- Back to System Update and you'll still get this the wrong update, do not worry, click on "MENU" and click on "Download the latest full package"
- You will now see the correct update "VIE-L09C432B360 2.39 GB" Now just click "hotfix"
- Do not download it, do not worry, just go to the Wi-Fi settings and disable "Proxy"
- Go back to the system upgrade and click pause and resume
- Wait until the end of the download, and after the phone will automatically install the update has been downloaded
If you have followed my instructions, it will be installed with B360 success.
Obviously you have to follow the signs quele for your version of firmware and that all root functions and how this suite if you had the miss and the directions that are on this forumo apply unfortunately for Andorid 6 'Marshmallow'.
Sorry for any typos or language.
Click to expand...
Click to collapse
This works takes time but it work´s
[email protected] said:
This works takes time but it work´s
Click to expand...
Click to collapse
The problem that the downloading takes a bit of time because the package is 2.6 GB. I even though the fiber 100 took almost a quarter of an hour. Then there is also the fact that the server knows where the file can be blocked by our connections. Try several times. One important thing and that the proxy anyway before starting the actual download is disabled.
I followed the steps, but I find myself with a version probably wrong, NRD90M test-keys, what should I do? Many basic functions do not work, I don't even have access to update function in settings.
bayers97 said:
I followed the steps, but I find myself with a version probably wrong, NRD90M test-keys, what should I do? Many basic functions do not work, I don't even have access to update function in settings.
Click to expand...
Click to collapse
I do not know which version of firmware you had, because I specified that ranged follow the directions according to the Roma who had one installed. My advice and try all over again. Keep in mind that just ago, having again put the VIE-L09C02B133 version and installing the new version directly using the TWRP recovery, me too I came out the same words 'NRD90M test-keys' that came out to you. In fact, now I'm starting all over again, starting to come from the VIE-L09C02B128 version and to follow.
I have an android car head unit with Allwinner T3.
I asked from the seller the OS files to update my unit because I was experiencing some issues. I received these two files
os_update_YMHC0101-N39-2.3.4.3.12_20180601_152348.zip
YMHC0101-N39-2.3.4.3.12_20180601_152348.img
I used the second file with PhonixCard to create a sd card and update my unit.
The update was successful and my unit information in About Device menu are:
Android version: 7.1.1
Hardware Information: Quad Core AllWinner
Kernel Version: Linux 3.10.65
OS Version: BSP 2.3.4.2.12 - IVT - 180601
MCU Version: 20180426-1-KC1-18
I want to install an app called VocalizerEx. The default TTS engine in my head unit is PicoTTS. I installed VocalizerEx and selected in settings but it's not activated. If I exit the menu and reenter I see that PicoTTS is the activated engine. I think that PicoTTS gets selected as the default TTS engine because it has been installed as a system app. I could convert VocalizerEx to system app if the head unit was rooted but I couldn't find any information to root my unit.
Since I have the above .zip and .img files I was wondering if there is a way to edit them and create a custom update file with VocalizerEx installed as a system app. If it's possible to edit these files I would like to change the boot animation as well.
I explore my head unit file structure and I see that it has the same file structure with the .zip file I have. Could I use this .zip to create the .img update file or just unpack and repack the .img?
I tried DragonFace but I got an error.
How could I edit this .img file? What tools do I need? (I could work on Windows/Linux/Mac OS X.)
Is it safe to unpack and repack the .img? Could a corrupted .img file brick my device?
Hey,
I have an Android Allwinner T3 device and I have problems with it.
I received operating system files from the vendor to update my unit. I received these three files:
- YMHC0101-N39-2.3.4.3.12_20180601_152348.img
- phonixcard.exe
- mcu-201804260001KC1-1522.img
Unfortunately, I have no instructions on how to do it. Could you write me one by one how to make an update?
_carlos_ said:
Hey,
I have an Android Allwinner T3 device and I have problems with it.
I received operating system files from the vendor to update my unit. I received these three files:
- YMHC0101-N39-2.3.4.3.12_20180601_152348.img
- phonixcard.exe
- mcu-201804260001KC1-1522.img
Unfortunately, I have no instructions on how to do it. Could you write me one by one how to make an update?
Click to expand...
Click to collapse
What problems do you have?
To update the OS:
1. Insert a formatted microSD card in an external microsd reader (computer's internal reader never worked for me)
2. Run phonicard as administrator. Select the .img file (YMHC0101-N39-2.3.4.3.12_20180601_152348.img), select the letter of your microSD, select "product" and hit "Run". After a few minutes you should see a green status bar or a message "Magic Complete/Burn End..." depending on Phonixcard version.
3. Turn off your headunit, remove all usb and sd cards from it, insert your new card in the GPS slot and turn it on. You should see a green bar loading. It takes about 1-2'. When it shows "CARD OK" on screen turn it off and remove the microSD.
4. Turn it on again and it should start booting. The first boot will take longer, 3-5'.
To update the MCU:
You should use another empty and formated microSD card. If you want to use the same, you should format it but also you should delete the hidden partition Phonixcard has created. Open Phonixcard with microSD connected and select "Format to Normal".
1. Copy mcu-201804260001KC1-1522.img in microSD card (copy the file in card, don't use Phonixcard to burn it).
2. Turn on you headunit and allow it to start. Remove all usb and sd cards and insert your microSD (with only mcu update in it).
3. Wait a few seconds and it should open a screen showing you that it found a MCU update. Select it and it should guide you through the process. Don't turn it off. Allow it to finish and reboot.
koroji said:
What problems do you have?
Click to expand...
Click to collapse
For me, there is a problem, that after selecting a home page, applications cyclically appear every 1 second and disappear. You can not start any application.
koroji said:
2. Run phonicard as administrator. Select the .img file (YMHC0101-N39-2.3.4.3.12_20180601_152348.img), select the letter of your microSD, select "product" and hit "Run".
Click to expand...
Click to collapse
Should I do it on my computer or Android Allwinner T3?
Yes, phonixcard is a computer program
Hello,
I have a problem with running the PhoenixCard application. I copied the applications onto the computer and opened it. I ran the PhoenixCard.exe file as an administrator. The user account control window appears: "Do you want to allow the following program from an unknown publisher to make changes to this computer?" I pressed the YES button, but the window disappears and nothing happens.
Please, tell me what to do.
Regards Robert
Write still what you used the phoenixcard version?
Where can I download firmware updates? I can't find vendor website.
You must write to the seller.
I've bought on Amazon... i'm sure that seller will not reply
Try it, I bought it on Aliexpress and the seller is replying to my messages.
---------- Post added at 11:42 PM ---------- Previous post was at 11:07 PM ----------
What is your exact model?
_carlos_ said:
Try it, I bought it on Aliexpress and the seller is replying to my messages.
---------- Post added at 11:42 PM ---------- Previous post was at 11:07 PM ----------
What is your exact model?
Click to expand...
Click to collapse
Czesc,
Pisalem na Elektrodzie do Ciebie w sprawie plikow do radyjka i dzialajacego PhoenixaCarda
Jak masz chwile daj znac lub linka na priv
Pzdr
Change your region via full OTA.
You do everything at your own risk, I am not responsible for any damages. The Chinese version cannot be changed in this way, please use this guide.
This guide allows you to change region within one Android version or upgrade without unlocking the bootloader. Android 13 prepackaged OTA files for India and EU regions will be listed here. If you want to switch to another region, you can ask the author of the post or edit the OTA file yourself according to this guide.According to this guide, user data will not be deleted.
Spoiler: Editing the payload-properties.txt file in full OTA
Download the full OTA from this link Move it to your device's internal memory To edit you will need an advanced device manager that you can download from the Play Store
Through the file manager, we find the OTA file that we are going to edit. Click on the file and open it in the manager, 3 files will open. Click on payload-properties.txt and change the line oplus_update_engine_verify_disable=0 to 1
We save in the upper right and you leave. The edited file will update in about 3 minutes. There may be an update error and there will be two zip archives in the folder, nothing wrong with that! We will keep both files but select the file without tmp to update.
Instructions : 1. Download the full OTA of the desired region and put it in the root directory of the internal memory.
RMX3301_11_C.20_IN
RMX3301_11_C.19_EUEX
RMX3301_11_C.19_RU
2. Installation of the OPLocal_ Update application. Go to your smartphone's settings, then Apps > Management. applications, 3 dots and check Show System ! Look for SOFTWARE UPDATE and clear this app's cache and data! Then install the OPLocal_ Update app for Android 12 or 13 (choose the version that is current on the device)
OPLocalUpdate_For_Android12.apk
OPLocalUpdate_For_Android13.apk
3. Installing an update through a third-party application! Next, open the app we installed and update it through it (gear top right and select the .zip file in the root directory of the internal memory), an installation window should appear! If everything is fine, the process will start and you will be prompted to restart your smartphone after installing the update. Installation takes 20-30 minutes.
After restarting your smartphone, you are in a new region.
It is recommended to flash the firmware file twice to flash both slots!
Many thanks to 4pda forum members KRD_RUS and [email protected] who created the tutorials.
Spoiler: Video instructions
Excellent tutorial. This was the only way possible, I was able to change the Rom from Global (previously Chinese) to INDIA region.
Thanks pal for all your help!
What is the point of changing to India region? Does the india rom have built in call Recorder?
I chose these regions because of the GDPR version and export.
Call recording has RU version.
Stano36 said:
I chose these regions because of the GDPR version and export.
Call recording has RU version.
Click to expand...
Click to collapse
Only RU has call Recorder?
How does this affect ota security updates?
The RU version has recording for sure.
OTA will run smoothly.
With this procedure I won't need to unlock the bootloader? So does that mean that NFC and banking apps don't work perfectly?
Yes, they will work without problems.
Hello
You only linked India and EU roms, is the RU rom available somewhere ?
Link added
from IN C12 my can't transfer through EUEX C12 this way? Thanks
You can
Does Russia have C 12 or only C 08 because Realme wont update due those stupid sanctions?
The Realme server only offers C.08, but C.12 should arrive by air.
Hi! I'm on GDPR version (GT2 RMX3311) and I wold like to unlock the bootloader by switching region to India, unlock via deep testing apk, and flash back the GDPR firmware, will this work? Will the bootloader remain unlock if I flash gdpr fw back?
Tried it, it doesn't work for GT 2.
@daniml3 tried it
So, I flashed the Indian ROM and all was fine, except that RIL didn't work, so l didn't have a working SIM and neither an IMEI, so I couldn't unlock the bootloader as it needs a working IMEI for that.
Click to expand...
Click to collapse
Has anyone tried to use the (RMX3311) "modem.img" in the (RMX3312) "payload.bin" and then to flash the RMX3312 FW on the RMX3311 GT2 ?
RMX3311 said:
Has anyone tried to use the (RMX3311) "modem.img" in the (RMX3312) "payload.bin" and then to flash the RMX3312 FW on the RMX3311 GT2 ?
Click to expand...
Click to collapse
I don't know about it
Thank you so much !
According this method, the Taiwan Ver. was successfully converted to the India Ver. Install google play coloros Phone APP. can automatically record calls
I have downloaded the firmware file and placed it in the root folder, but the updater still says "Move installation package into root directory".
Help would be appreciated. Thanks.