Hey, I just received ->THIS<- case that I ordered on 27th of July. It's made from silicone with nice grip on the back
Case from back
Case from front
The power and volume buttons are hidden under the case but the alert slider is not and it's deep enough that u can't switch it with one hand and you have to use nail to switch it to different position
Power Button
Volume buttons and Alert Slider
Detail on Alert Slider
The cutouts on the bottom are wide enough that you can put bigger headphone jacks in and Dash Charge cable is perfect fit. The case doesn't block the speakers at all neither the microphone.
Bottom cutouts
The case is big enough to cover the camera bump so the camera doesn't protrude at all
Camera cutout
It's a bumper case so there the screen won't get scratch up when you put the phone upside down on table.
When I look at the case from sides it looks like it should be possible to apply Orzly Tempered Glass V2 or practically any Tempered Glass. I might order the Orzly one later.
Front from angle
Front from top
One last thing I want to point out is that this case is like magnet for dust,It was lying on table and I moved it a little on table,as soon as I picked it up I noticed that the back of the case took ale the dust I had there. It's not a big deal though you can easily clean by swiping them.
Back with dust
Here is the whole album if you don't want to click link by link
If you have any questions,you are allowed to ask
Just got pretty much the same case but this version has cutouts for all 3 and the same cutout for the camera.
djsubterrain said:
Just got pretty much the same case but this version has cutouts for all 3 and the same cutout for the camera.
Click to expand...
Click to collapse
Yeah I saw few versions of this case
Thanks for sharing! Id rather this over the stock OP Karbon Bumper one tbh haha
Related
Link
Alright, The case the box came is in is kind of girly, anyways the quality of the case is amazing! It doesn't feel like it was cheaply made at all. It doesn't add too much bulk and I can still fit it in my skinnys(Levi's 511 Skinny 29 x 30) front pocket. The buttons are easily accessible even the the volume button being covered by the front flap it is still easy to press / locate since the case has a steep cut out for the volume buttons. Aswell as the S-Pen being so easily accessible. An added perk i liked about this case is that the speaker hole is actually covered by its own mesh. It also has an accessory hole so you could attach an accessory / lanyard to it. The Magnetized kick stand does not interfere with signal(atleast none i can tell).
Album
Zenus cases are the best I've seen so far for the Galaxy Note. I was thinking of getting this one as well but the color combinations just don't do it for me. Also, there's not cutout for the front speaker so it would be a little awkward to have to hold the front leather part back every time. I like that the case clips onto the metal part on the side and doesn't rest on the top of the phone so that a screen guard will thankfully be left untouched. I also love that it has a stand (The only reason I'm not getting the Zenus Masstige Stripe Case). I was wondering though, when the stand is set up, does the little latch (idk what it's called lol, the little thing used to clip on to the front cover to close the case) hide a little part of the screen since presumably, it'll be hanging down a little bit?
EDIT: Ordered it lol. It may have its flaws but it's the best I could find at its price range.
I have one of these (different colors, but this color looks great).
They are extremely high quality. As good or better than Vaja, for instance.
I've posted this before, that make sure you pay more and get the leather ones, as they have a few lines and some of the lines aren't as good quality.
This particular case is just great. The flap is a tad annoying but well worth it overall.
Note: one thing worth mentioning is that they are very light also.
would it be okay to use this case with a FULL skin applied? Ie. sides and back??
i'm sure the front would be okay, but just wanted to see if the sides of the phone with skin be okay.....
i've been looking at cases that have the flip cover, but they all look like it would peel off the side skins..... this one looks like it like it might be okay.
predation said:
would it be okay to use this case with a FULL skin applied? Ie. sides and back??
i'm sure the front would be okay, but just wanted to see if the sides of the phone with skin be okay.....
i've been looking at cases that have the flip cover, but they all look like it would peel off the side skins..... this one looks like it like it might be okay.
Click to expand...
Click to collapse
Hmmm...that's a tricky one. Obviously, it clips in tightly and securely so it might damage the skin during insertion and removal but once it's sitting in there, as long as you don't constantly remove it, it should be fine. I would recommend going to a store and testing out either this case or similar leather cases, but then again, if you harm the skin in the process, then this whole discussion is useless lol. On another note, why use a skin? The note is such a beautiful sleek beast. I wouldn't want to hide away any of the sides or take away from the beautiful protruding glass. That's why I hate my current Capdase Jacket XPose and am going for this case. Just increases the beauty XD. Anyways, yes, back on topic, I wouldn't recommend using a skin with this cover but hopefully someone who's actually tried it will reply.
Side-note: I ordered the Wine-Red / Dark Brown version
predation said:
would it be okay to use this case with a FULL skin applied? Ie. sides and back??
i'm sure the front would be okay, but just wanted to see if the sides of the phone with skin be okay.....
i've been looking at cases that have the flip cover, but they all look like it would peel off the side skins..... this one looks like it like it might be okay.
Click to expand...
Click to collapse
Here's a Flip case that would most likely not interrupt your skin.
Link
xCeejayy said:
The aluminum bumper wasn't doing it for me so I was looking around and I found this case. The colors are pretty subtle and calm. I'll update this with a review / pics of the case on when I receive it. I just wanted to share this case with you because it just looks so nice.
Link
Alright, The case came in the box it comes in is kind of girly, anyways the quality of the case is amazing! It doesn't feel like it was cheaply made at all. It doesn't add too much bulk and I can still fit it in my skinnys(Levi's 511 Skinny 29 x 30) front pocket. The buttons are easily accessible even the the volume button being covered by the front flap it is still easy to press / locate since the case has a steep cut out for the volume buttons. Aswell as the S-Pen being so easily accessible. An added perk i liked about this case is that the speaker hole is actually covered by its own mesh. It also has an accessory hole so you could attach an accessory / lanyard to it. The Magnetized kick stand does not interfere with signal(atleast none i can tell).
Album
Click to expand...
Click to collapse
These Zenus cases look great and seem very usable. But the downside is that they have a magnet at the back that interferes with S-pen functions (not with the signal). Check in the screen area in front of the magnet by trying to draw several long thin lines with the SPen that cross this area. That case was a money waste for me...
drkalo said:
These Zenus cases look great and seem very usable. But the downside is that they have a magnet at the back that interferes with S-pen functions (not with the signal). Check in the screen area in front of the magnet by trying to draw several long thin lines with the SPen that cross this area. That case was a money waste for me...
Click to expand...
Click to collapse
I tried this and it works fine for me Maybe contact Zenus for another one?
xCeejayy said:
I tried this and it works fine for me Maybe contact Zenus for another one?
Click to expand...
Click to collapse
I got these symptoms after a couple of days usage. I contacted the dealer and got a substitute with Capsule Stand Slide Series - White / Lime
When I got my Note off CL came with the Eel leather case. It's slick but I wish it was the capsule.
Sent from my SAMSUNG-SGH-I717 using xda premium
Hello!
I am using the original S View Cover with my Note 3. It fell down and the bezel on the left side is broken. I don't want to use the S View Cover anymore but the bezel is missing and the volume button can fall out easily. I don't want have it repaired it's expensive, around £100. I'm looking for a very thin case or bumper so it can cover the bezel properly and protect the volume button. Can anyone suggest me good bumper or thin case and screen protector?
Tick plastic Bumper case is good
david576 said:
Hello!
I am using the original S View Cover with my Note 3. It fell down and the bezel on the left side is broken. I don't want to use the S View Cover anymore but the bezel is missing and the volume button can fall out easily. I don't want have it repaired it's expensive, around £100. I'm looking for a very thin case or bumper so it can cover the bezel properly and protect the volume button. Can anyone suggest me good bumper or thin case and screen protector?
Click to expand...
Click to collapse
I dropped my Note 3 once and got scratches in the Bezel. so I bought one similar to the one below and it helped a lot as I have dropped my phone nearly 6 times after that
http://www.ebay.com/itm/Frame-Bumpe...N9000-Black-/371171835535?hash=item566b90be8f
I was wondering if anyone had recommendations on a TPU Gel Case, I was looking for something with a low profile that still gives solid protection without blocking to much of the "edge" display.
I have seen a couple a couple from Spigen and LK that look promising, but was wondering if anyone has first-hand experience with a good case. The main things I want are
1. Grippy/Flexible TPU
2. Protection of the frame at top/bottom
3. Lots of lift on top/bottom or corners to give clearance if you lay the phone flat on the screen
4. Full access to screen (cover the least amount of edge function as necessary)
5. As thin a profile as possible with the other requirements
https://www.amazon.com/Spigen-Crystal-Glitter-Protection-Premium/dp/B06XP41W7Y
https://www.amazon.com/Spigen-Surface-Excellent-Compatible-Samsung/dp/B06XP54BCW
https://www.amazon.com/Spigen-Crystal-Protection-Premium-Clarity/dp/B06XP6KZKC
https://www.amazon.com/LK-Scratch-Resistant-Silicone-Protective/dp/B01N9SJB3J
Thanks in advance
I have about a dozen cases and this is one of my favorites. Great price and great quality.
https://www.amazon.com/TUDIA-Galaxy...=UTF8&qid=1494359654&sr=1-4&keywords=tudia+s8
Does that Tudia case have any grip?
I'm looking for a S8 case that's like the Apple 7+ silicone case if you know how grippy those are.
SLMcc said:
Does that Tudia case have any grip?
I'm looking for a S8 case that's like the Apple 7+ silicone case if you know how grippy those are.
Click to expand...
Click to collapse
Not familiar with those, but the Tudia has etched sides to add grip. Some others I have are smooth and can be a bit slippery. The Tudia feels great in the hand.
arampapaz said:
Not familiar with those, but the Tudia has etched sides to add grip. Some others I have are smooth and can be a bit slippery. The Tudia feels great in the hand.
Click to expand...
Click to collapse
Okay, thanks. They are more like silicone than TPU and have awesome grip. They have a microfiber lining too so they don't leave marks, etc on the back of the phone. I'm looking for something like that if I can find one.
Nillkin nature, best case ever. If you give a try, you will use it in all your phones in the future. I used it with my last 3 phones.
Moreover, the case fixes the Fingerprint failed location issue. You will never touch your camera lens anymore.
adrimg01 said:
Nillkin nature, best case ever. If you give a try, you will use it in all your phones in the future. I used it with my last 3 phones.
Moreover, the case fixes the Fingerprint failed location issue. You will never tiuch your camera lens anymore.
Click to expand...
Click to collapse
I agree! I just received my Nillkin Nature case (clear) and it's the best! :good:
Thanks for the suggestions guys, I was looking for something with a style similar to the Nillkin, Silicone iPhone cases that you described.
I definitely like the idea of having the camera and sensors separated on the back. My one concern for the Nillkin is about screen protection. Is the lip on the top/bottom substantial enough to protect the screen?
https://www.amazon.com/Galaxy-Nillkin-Nature-Clear-Samsung/dp/B06ZZBRNK2?th=1
I was also looking at this case which wraps over the top and bottom bezels and at least seems like it might give more protection, although it doesn't separate the sensors on the back
https://www.amazon.com/LK-Scratch-Resistant-Silicone-Protective/dp/B01N6RRU2D?th=1
Or this one which is similar to the Nillkin, but has more corner protection
https://www.amazon.com/DAUPIN-Crystal-Protection-Premium-Clarity/dp/B06Y2S81VG
Thanks again for the help
i recommend the Ringke Fusin case.. its fit perfectully to all ur's demands.. im using it since i got my S8 (a month ago) and absolutly love it
1. Grippy/Flexible TPU
2. Protection of the frame at top/bottom
3. Lots of lift on top/bottom or corners to give clearance if you lay the phone flat on the screen
4. Full access to screen (cover the least amount of edge function as necessary)
5. As thin a profile as possible with the other requirements
https://www.amazon.com/Ringke-Trans...qid=1494594537&sr=1-1&keywords=ringke+s8&th=1
Pl2lNCE said:
Thanks for the suggestions guys, I was looking for something with a style similar to the Nillkin, Silicone iPhone cases that you described.
I definitely like the idea of having the camera and sensors separated on the back. My one concern for the Nillkin is about screen protection. Is the lip on the top/bottom substantial enough to protect the screen?
https://www.amazon.com/Galaxy-Nillkin-Nature-Clear-Samsung/dp/B06ZZBRNK2?th=1
I was also looking at this case which wraps over the top and bottom bezels and at least seems like it might give more protection, although it doesn't separate the sensors on the back
https://www.amazon.com/LK-Scratch-Resistant-Silicone-Protective/dp/B01N6RRU2D?th=1
Or this one which is similar to the Nillkin, but has more corner protection
https://www.amazon.com/DAUPIN-Crystal-Protection-Premium-Clarity/dp/B06Y2S81VG
Thanks again for the help
Click to expand...
Click to collapse
If you put your phone face down with the Nillkin nature case, the screen doesn't touch the surface, so the lip on the top and bottom are enough.
But what I like the most of this case, is how are separated the camera and the Fingerprint sensor. The hole for the camera is so small that is no possible to touch the camera lens anymore (unless you have a very thin finger). On the other hand is the Fingerprint sensor hole so big, that your finger falls naturally in the right position, while without a case the 50% the times is touching the camera.
Between, if you have the midnight black version and you decide to get the Nillkin, go for the grey one. It looks awesome and much better than the clear one.
Catman Gold trim transparent case
Ordered on Jun 20th, shipped Jun 21st and delivered on Jul 11th
I was looking for a cheap transparent bumper protective case. I liked the idea that this case had a gold trim that would standout with most skins or the naked midnight black phone itself. I was suspicious that the gold trim would not look nearly as shiny metallic as in their advert pictures but I was dead wrong. Only time will tell if the gold trim cracks or peels. During my initial inspection it doesn't look like there is any way the gold can peal as it's completely embedded into the plastic.
The case was applied over a dBrand Mahogany skin but I suspect it would look even better with the midnight black naked OP5 or any black skin as it would help make the gold trim stand out even more. As can be seen in the attached pictures only the power and volume rocker buttons are covered by the case. That is where the case is thinnest and may wear out over time.
There appears to be plenty of room for the Orzly tempered glass screen protector that I've ordered as the lip of the case doesn't cover the 3D curved screen edge or the OnePlus factory applied screen protector. I'll add a comment about the Orzly tpsp when it's delivered. In general the cover is thin so hardly adds any bulk to the phone unlike the usual bumper cases I've used. In fact it looks so good I'm going to leave it on all the time, rather than just occasionally as I'd originally planned. Only time will tell if that will change.
The case doesn't interfere with any of the bottom ports (speaker, charger, headphone jack ... etc). The cover is every so slightly skewed around the back camera and flash holes but is only noticeable on close inspection rather than being an obstruction. The covers on the power and volume rockers are pleasantly non-intrusive. That is compared to my much more expensive Spigen bumper case on my previous phone.
This case also included a plastic screen protector that is tinted blue I assume to be anti-glare. I'll not be using that screen protector in lieu of the Orzly tpsp.
3DSammy said:
Catman Gold trim transparent case
Ordered on Jun 20th, shipped Jun 21st and delivered on Jul 11th
I was looking for a cheap transparent bumper protective case. I liked the idea that this case had a gold trim that would standout with most skins or the naked midnight black phone itself. I was suspicious that the gold trim would not look nearly as shiny metallic as in their advert pictures but I was dead wrong. Only time will tell if the gold trim cracks or peels. During my initial inspection it doesn't look like there is any way the gold can peal as it's completely embedded into the plastic.
The case was applied over a dBrand Mahogany skin but I suspect it would look even better with the midnight black naked OP5 or any black skin as it would help make the gold trim stand out even more. As can be seen in the attached pictures only the power and volume rocker buttons are covered by the case. That is where the case is thinnest and may wear out over time.
There appears to be plenty of room for the Orzly tempered glass screen protector that I've ordered as the lip of the case doesn't cover the 3D curved screen edge or the OnePlus factory applied screen protector. I'll add a comment about the Orzly tpsp when it's delivered. In general the cover is thin so hardly adds any bulk to the phone unlike the usual bumper cases I've used. In fact it looks so good I'm going to leave it on all the time, rather than just occasionally as I'd originally planned. Only time will tell if that will change.
The case doesn't interfere with any of the bottom ports (speaker, charger, headphone jack ... etc). The cover is every so slightly skewed around the back camera and flash holes but is only noticeable on close inspection rather than being an obstruction. The covers on the power and volume rockers are pleasantly non-intrusive. That is compared to my much more expensive Spigen bumper case on my previous phone.
This case also included a plastic screen protector that is tinted blue I assume to be anti-glare. I'll not be using that screen protector in lieu of the Orzly tpsp.
Click to expand...
Click to collapse
Wouldn't the transparent part of the case yellow over time?
I don't know, only time will tell. Any way it's only $8 USD so no big loss. Have you had yellowing with a clear case before?
looks cool,
i ordered the black version. should arive soon
3DSammy said:
I don't know, only time will tell. Any way it's only $8 USD so no big loss. Have you had yellowing with a clear case before?
Click to expand...
Click to collapse
Oh yea. With the Ringke fusion for my OPO. The borders were TPU I think, looked really dirty after about 2 months.
I cant find a good case for ROG 3 on flipkart of Amazon. Which case are you guys using? where did you buy it from??
I am using Lighting Armor case as I need to use the air trigger. If you do not care for the function of air triggers (dual & slide), can get IMAK case from aliexpress.
I'm also using the lighting armour , I like it ok it drains power but I still like it
I am using the average tpu case that is available for rog 3, i had to make cut out for the side mounted type c ports though
I'm using this: https://www.aliexpress.com/item/4001345047036.html?spm=a2g0s.9042311.0.0.5d6e4c4d4DwYCq
It's not perfect, but provides enough all around protection, the cutouts are in place.
The included tempered glass screen protector is of good quality, but the black border covers a few pixels on the sides.
It's pretty cheap, I can recommend buying it to protect your ROG Phone 3 - as I said, it's not perfect, but good enough.
Using this one with a tempered glass in the front and a silicon film in the back
I have ordered this IMAK transparent black TPU case with extra corner shock-proofing along with these IMAK clear soft hydrogel films for front & back protection.
Hopefully shipment arriving to me by early next month.
Used to use the lighting armor case until the slippery uncovered aluminium side caused me to drop the phone yesterday, now the phone has a dent on the top right corner of the frame. Lighting armor has the best look of all the cases out there. Now using Zshow case which should prevent it from hitting the screen flat down if I ever drop it again. I'm lucky the phone didn't fall face down with the lighting armor case which would have guaranteed a cracked screen.
I have the imak tpu case too but it cause the tempered glass to lift.
Besides the tempered glass being lifted issue, what's your experience/ feedback regarding your IMAK TPU case (is it with extra corner protection)?
Imak case is quite loose around the air triggers, power button, volume button and side port. Top 4 corner airbags are the problems as they can be depressed quite easily and this cause the screen protector to lift up. You will know when you hold the phone on your right hand with your palm resting with the bottom right corner for support, and this can cause the screen protector to lift.
I'm getting the hydrogel film screen protectors - Hoping that screen lift is not an issue.....
What's your experience or opinion regarding the general damage/ drop protection with this case?
Quality, overall fitting & feel?
It will protect if dropping on the corners as well as face down. However dropping on the back might be a problem because the camera lens are protuting out (although the case cover the camera lens). Placing the phone on the table will also result in wobbly phone when using.
---------- Post added at 06:15 AM ---------- Previous post was at 06:13 AM ----------
Quality, would say it is better than those generic cheap tpu case (which has worse fit than imak), feel wise, it is slippery on the back.
I just received this: Foluu ROG Phone 3 Case through Amazon. £6.71. To hold it without the phone it doesn't feel great and whilst over the standard case it comes with its bulkier I feel so much safer knowing my camera wont get scratched when I put the phone down. It also raises of the front screen by a minuet amount so there is a bump as you move your finger about. I'd rather that than a nasty scratch though so happy with it.
Air trigger holes and extra power connector cut out too as well as on the back a nice design
punchuk said:
I just received this: Foluu ROG Phone 3 Case through Amazon. £6.71. To hold it without the phone it doesn't feel great and whilst over the standard case it comes with its bulkier I feel so much safer knowing my camera wont get scratched when I put the phone down. It also raises of the front screen by a minuet amount so there is a bump as you move your finger about. I'd rather that than a nasty scratch though so happy with it.
Air trigger holes and extra power connector cut out too as well as on the back a nice design
Click to expand...
Click to collapse
It covers the side? The picture on amazon looks like it is an open side design. I don't see slapping that case will provide a good grip.
lornranger said:
Imak case is quite loose around the air triggers, power button, volume button and side port. Top 4 corner airbags are the problems as they can be depressed quite easily and this cause the screen protector to lift up. You will know when you hold the phone on your right hand with your palm resting with the bottom right corner for support, and this can cause the screen protector to lift.
Click to expand...
Click to collapse
Hi mate i suggest to use Asus Antibatteric screen protector It has and awesome response and great oleophobic protection.
Davisk8 said:
Hi mate i suggest to use Asus Antibatteric screen protector It has and awesome response and great oleophobic protection.
Click to expand...
Click to collapse
I am using Asus Original Screen Protector without antibacterial coating. The antibacterial protector is not available in my country. Great protector, no blocking of edge unlike the cheap china protector which has thick black borders and block the edges of the display.
punchuk said:
I just received this: Foluu ROG Phone 3 Case through Amazon. £6.71. To hold it without the phone it doesn't feel great and whilst over the standard case it comes with its bulkier I feel so much safer knowing my camera wont get scratched when I put the phone down. It also raises of the front screen by a minuet amount so there is a bump as you move your finger about. I'd rather that than a nasty scratch though so happy with it.
Air trigger holes and extra power connector cut out too as well as on the back a nice design
Click to expand...
Click to collapse
Thanks for this, I did think about getting this over.
I'm using the magnetic flip case which is great, but no front lip so don't drop the thing like I did, broke my display as the screen protector didn't quite cover all of it and a tiny stone hit the outer edge.
Not the end though as I've bought another, and will get it repaired under insurance consider it a lesson learned.
￡2.32 23%OFF | Safety protective Glass for Asus Rog Phone 3 ZS661KS Oleophobic Screen Protector For ROG Phone 3 Strix Tempered Glass Film
https://a.aliexpress.com/_B0aeTT
This was with the rog case which in all honesty shouldn't come with it.
This is the protector, don't bother with it, I've another coming that has smooth edges, looks decent so will see.
Turns out the one I've ordered might be the same Asus sells.
￡1.59 | For Asus ROG Phone 3 Phone3 ZS661KS / Strix 6.59" 21D 9D Full Glue Cover Toughened Tempered Glass Film Screen Protector Guard
https://a.aliexpress.com/_B0iH9b
the lighting case but I installed a diy wireless charger because I have so many already laying around
[/COLOR]
elmor0 said:
I have ordered this IMAK transparent black TPU case with extra corner shock-proofing along with these IMAK clear soft hydrogel films for front & back protection.
Hopefully shipment arriving to me by early next month.
Click to expand...
Click to collapse
FEEDBACK
Took about 5 weeks to arrive (from China).
This IMAK case is good build quality and fit over all, could have been a bit more snug - the extra corner padding does not make it look slick, and I am not sure if it is worth it on balance.
There is a 2 mm lip all around the front panel to help with screen protection.
Cut-outs are spot on - including for air-triggers/ 3 mics/ heat vent/ side USB ports. No cut-out for SIM-tray though but it's better this way.
Camera module is fairly well protected.
No issues with air-trigger related squeeze gestures.
The Hydrogel clear gel screen protector had a ?extra notch cut-out just left of the front camera (?? why) but otherwise the rest of the dimensions were spot on. It came as a set of x2 in one pack, which was a nice surprise. Included a helpful set of instructions/ link to video.
I preferred it to be short by about 1 mm all around the edges to minimise the risk of "lift" when the case is compressed in pockets/ when using the squeeze gestures etc.
The touch feel is smooth and has a good response. Visibility through this screen film is fine; no glare issues. I prefer these type of gel screen protectors to glass.
Has anyone come across a case that doesn't need to be removed when connecting to the accessories (eg Twinview, Mobile Desktop Dock)?