Must Have An Unlocked Bootloader To Do This!
This A full stock firmware file I have created to flash with odin to automatically install TWRP recovery along with Disable VBMETA image. The Userdata _AIO tar file will also automatically install magislk root along with remove force encryption and patch bluetooth library file. It will also patch safetynet. No flashing of zips is required
Info For Bootloader Unlocks Can Be Found In Post 2
I Do Not Recommend Mixing Bit 1 And Bit 2 Firmware!!!!
Downloads
SM-G981U/U1/W- Model
G981USQU3HWB3_Bit1_Safe --This will bring you to Android 13 without loosing unlock
SM-G986U/U1/W- Model
G986USQU3HWB3_Bit1_Safe --This will bring you to Android 13 without loosing unlock
SM-G988U/U1/W- Model
G988USQU3HWB3_Bit1_Safe --This will bring you to Android 13 without loosing unlock
Odin3_v3.14.1_3B_PatcheD.zip
TWRP Recovery Provide by @afaneh92
Be prepared to have your data wiped. The process tries to determine if you do or do not need to have data wipe but as a precaution just assume your data will be wiped. Especially if using U1 or W firmware
Install Instructions
You must be OEM Unlocked Bootloader
1. On Initial unlock of phone you must through setup and be signed into your google account.
2. Reboot phone too download mode and make sure KG STATUS=CHECKING (see pic) and not PRENORMAL. If PRENORMAL then do step 1 again
View attachment 5217631
3. Use patched 3.14 odin and load files in appropriate odin slots
4. Phone will reboot to TWRP and remove encryption which will wipe phone. Phone will reboot back too TWRP to finish install then reboot to setup
Features
No patches or mod zips are needed phone will already be rooted
Fix Safetynet
Bluetooth is patched for pairing to survive reboots
Samsung Health working
Bugs
Samsung Pay, Secure Folder and Samsung Pass do not work as on most Samsung Rooted Roms
Thanks To People That Make My Life Easier
elliwigy
klabit87
Krog18
me2151
stang5litre
Raymonf for modified odin
rayan-refoua for boot animation
TheMadScientist
afaneh92
kdrag0n for safetynet fix
3arthur6 for bluetooth patch zip
JDBarlow for test S20 stuff
markfm For Bitsafe Firmware
Source For Userdata AIO
Info For U Model Bootloader Unlocking Can Be Found
[Android][UNSAMLOCK] Bootloader Unlock for Samsung US/Canada Devices
This thread is @svetius approved Important notice: Do not update to April 2023 security update (XXXXXXXXXXWCX) or later. Examples: G998USQS6EWCA, N986USQU4HWD1. Samsung has patched the bootloader unlock again on those updates. NOTE: The OneUI...
forum.xda-developers.com
Below US snapdragon devices can be bootloader unlocked with above service as long as bootloader version meets below criteria. Bootloader version can be determined from the 5th character from the right on the baseband version or build number, in some cases from kernel version
Z Fold2 5G BL V1
Fold 5G BL V1-4
Fold BL V1-4
Z Flip 5G BL V1
Z Flip BL V1-3
Note series 20 BL V1
S20 series BL V1
S20 FE 5G BL V1-2
Note 10 series BL V1-5
S10 Lite BL V1-3
Note 10+ 5G N976U BL V1-4
Note 10+ 5G N976V BL V1-5
S10 5G BL V1-5
S10 series BL V1-4
Note 9 BL V1-7
S9 series BL V1-9
Tab S6 BL V1-3
Tab S7 BL V1
Tab S7+ BL V1
A71 5G BL V1-2
A51 BL V1-5
A51 5G BL V1-4
A50 A505W BL V1-A
A50 A505U BL V1-B
S21 BL V1
A32 5G BL V1-3
Tab Active Pro 10.1 BL V1-4
XCover Pro BL V1-7
Good to see you here, I will make use of this. Thanks, I hope to see you playing with roms!
jhr5474 said:
Good to see you here, I will make use of this. Thanks, I hope to see you playing with roms!
Click to expand...
Click to collapse
I dont have s20 so Im limited what I can make
If tokens can be updated to flash higher bootloaders then I will adjust files accordingly
This works great! I flashed the entire U1 DUB7 update with the force wipe with BL files in the USERDATA slot. Everything went well.
Tried this on my G981V and failed on (auth). Was worth the try although I soft bricked my phone lol
scepz said:
Tried this on my G981V and failed on (auth). Was worth the try although I soft bricked my phone lol
Click to expand...
Click to collapse
So please give more info. What file you tried flash. You should be able to flash the ones that don’t have bootloaders in them
jrkruse said:
So please give more info. What file you tried flash. You should be able to flash the ones that don’t have bootloaders in them
Click to expand...
Click to collapse
Both files that say contain bootloader from UI 3.0 and that I'll keep my unlock token. kg status was checking as well.
scepz said:
Both files that say contain bootloader from UI 3.0 and that I'll keep my unlock token. kg status was checking as well.
Click to expand...
Click to collapse
Sorry I had no clue there was an sm-g981v mode. Just don’t flash the bl file of your stock firmware and you will be fine using my userdata without bl files
jrkruse said:
Sorry I had no clue there was an sm-g981v mode. Just don’t flash the bl file of your stock firmware and you will be fine using my userdata without bl files
Click to expand...
Click to collapse
I tried with just your user data file still didn't work. So your saying next time use all files besides BL?
scepz said:
I tried with just your user data file still didn't work. So your saying next time use all files besides BL?
Click to expand...
Click to collapse
I'll make a specific one for sm-g981v
jrkruse said:
I'll make a specific one for sm-g981v
Click to expand...
Click to collapse
Ok
scepz said:
Ok
Click to expand...
Click to collapse
files in the OP
jrkruse said:
Must Have An Unlocked Bootloader To Do This!
This An odin tar file I have created to flash along with stock odin firmware to automatically install TWRP recovery along with Disable VBMETA image. The tar file will also automatically install magislk root along with remove force encryption and patch bluetooth library file. It will also patch safetynet. No flashing of zips is required
Info For Bootloader Unlocks Can Be Found In Post 2
Downloads
SM-G981U/U1/W- Model
These contains bootloaders from One UI 3.0 firmware so you will not loose token and do not need to alter firmware you are flashing
They contain bootloaders too allow you too load full stock One UI 3.1 firmware in odin without having to worry about removing certain files as the bootloaders in the USERDATA file will keep you on the correct bootloaders.
USERDATA_AIO_G981_FORCE_WIPE.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G981_NO_WIPE.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
These do not contains bootloaders from One UI 3.0 firmware and you will loose token if you flash higher version bootloaders unless you alter the firmware. You can use these to do the firmware as you see fit.
USERDATA_AIO_G981_FORCE_WIPE_NO_BL.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G981_NO_WIPE_NO_BL.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
SM-G981V- Model
These contains bootloaders from One UI 3.0 firmware so you will not loose token and do not need to alter firmware you are flashing
They contain bootloaders too allow you too load full stock One UI 3.1 firmware in odin without having to worry about removing certain files as the bootloaders in the USERDATA file will keep you on the correct bootloaders.
USERDATA_AIO_G981V_FORCE_WIPE.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G981V_NO_WIPE.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
These do not contains bootloaders from One UI 3.0 firmware and you will loose token if you flash higher version bootloaders unless you alter the firmware. You can use these to do the firmware as you see fit.
USERDATA_AIO_G981V_FORCE_WIPE_NO_BL.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G981V_NO_WIPE_NO_BL.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
SM-G986U/U1/W- Model
These contains bootloaders from One UI 3.0 firmware so you will not loose token and do not need to alter firmware you are flashing
They contain bootloaders too allow you too load full stock One UI 3.1 firmware in odin without having to worry about removing certain files as the bootloaders in the USERDATA file will keep you on the correct bootloaders.
USERDATA_AIO_G986_FORCE_WIPE.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G986_NO_WIPE.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
These do not contains bootloaders from One UI 3.0 firmware and you will loose token if you flash higher version bootloaders unless you alter the firmware. You can use these to do the firmware as you see fit.
USERDATA_AIO_G986_FORCE_WIPE_NO_BL.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G986_NO_WIPE_NO_BL.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
SM-G988U/U1/W- Model
These contains bootloaders from One UI 3.0 firmware so you will not loose token and do not need to alter firmware you are flashing
They contain bootloaders too allow you too load full stock One UI 3.1 firmware in odin without having to worry about removing certain files as the bootloaders in the USERDATA file will keep you on the correct bootloaders.
USERDATA_AIO_G988_FORCE_WIPE.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G988_NO_WIPE.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
These do not contains bootloaders from One UI 3.0 firmware and you will loose token if you flash higher version bootloaders unless you alter the firmware. You can use these to do the firmware as you see fit.
USERDATA_AIO_G988_FORCE_WIPE_NO_BL.tar.md5
This will force a wipe of data no mater what. This Must Be Used On U1 Firmware and can be used on U firmware if you choose so.
USERDATA_AIO_G988_NO_WIPE_NO_BL.tar.md5
This will only wipe if you have encrypted data. This Can Only Be Used On U firmware
Odin3_v3.14.1_3B_PatcheD.zip
TWRP Recovery Provide by @afaneh92
Be prepared to have your data wiped. The process tries to determine if you do or do not need to have data wipe but as a precaution just assume your data will be wiped. Especially if using U1 or W firmware
Install Instructions For Newly Unlocked Devices
You must be OEM Unlocked Bootloader
1. On Initial unlock of phone you must through setup and be signed into your google account.
2. Reboot phone too download mode and make sure KG STATUS=CHECKING (see pic) and not PRENORMAL. If PRENORMAL then do step 1 again
View attachment 5217631
3. Use patched 3.14 odin and load file USERDATA_SLOT_G98*U_**.tar.md5 you must choose one of the FORCE_WIPE files and load in the USERSDATA slot of odin and flash file
4. Phone will reboot to TWRP and remove encryption which will wipe phone. Phone will reboot back too TWRP to finish install then reboot to setup
Install Instructions For Updating Firmware On Phone Already Unlocked
1. Reboot phone too download mode and make sure KG STATUS=CHECKING. If not see above
2. Use patched 3.14 odin and load stock firmware in appropriate slots use regular CSC file in the CSC slot and load file one of the USERDATA_SLOT_G98*U_**.tar.md5 in the USERSDATA slot of odin and flash firmware. Do not use the User Data file that comes with firmware.
3. Phone will reboot to TWRP and check for encryption and remove if needed which will wipe phone. If phone is not encrypted data will not be wiped. Phone will reboot back too TWRP to finish install then reboot to setup if data was wiped or reboot normally if it was not
Install Instructions If Updating Images With TWRP
1. When done flashing images in TWRP Reboot phone too download mode and make sure KG STATUS=CHECKING. If not see above.
2. Use patched 3.14 odin and load file USERDATA_AIO_G98*_NO_WIPE_NO_BL.tar.md5 in the USERSDATA slot of odin and flash file.
3. Phone will reboot to TWRP and check for encryption and remove if needed which will wipe phone. If phone is not encrypted data will not be wiped. Phone will reboot back too TWRP to finish install then reboot to setup if data was wiped or reboot normally if it was not.
4. Alternatively to using USERDATA_AIO_G98*_NO_WIPE_NO_BL.tar.md5 in odin you can use AIO_Magisk_22_S20_Series.zip found in post 2
Features
No patches or mod zips are needed phone will already be rooted
Fix Safetynet
Bluetooth is patched for pairing to survive reboots
Samsung Health working
Bugs
Samsung Pay, Secure Folder and Samsung Pass do not work as on most Samsung Rooted Roms
Thanks To People That Make My Life Easier
@elliwigy
@klabit87
@Krog18
@me2151
@stang5litre
@Raymonf for modified odin
@rayan-refoua for boot animation
@TheMadScientist
@afaneh92
@kdrag0n for safetynet fix
3arthur6 for bluetooth patch zip
@JDBarlow for test S20 stuff
Click to expand...
Click to collapse
Does this work on s20 plus g9860?
If not...can you make a file for SM-G9860 TGY.
This is the link for latest firmware
Download Samsung Galaxy S20+ SM-G9860 TGY Hong Kong firmware
All Samsung firmwares for Galaxy S20+ in Hong Kong with model code SM-G9860. We offer free and fast download options. Check them out now.
www.sammobile.com
Gianni's said:
Does this work on s20 plus g9860?
If not...can you make a file for SM-G9860 TGY.
This is the link for latest firmware
Download Samsung Galaxy S20+ SM-G9860 TGY Hong Kong firmware
All Samsung firmwares for Galaxy S20+ in Hong Kong with model code SM-G9860. We offer free and fast download options. Check them out now.
www.sammobile.com
Click to expand...
Click to collapse
The ones without bootloaders will work. The NO_BL ones. Probably have to use the force wipe one
So, if I have the S20+ (US Cellular) and want to try the 3.1 firmware:
1.) Download the firmware
2.) Put your file for it into user data field in Odin
3.) Put in AP, CSC (home or whatever to not overwrite my USC one I think) and the rest EXCEPT for the bootloader into Odin
4.) Flash as usual and then everything should work. I'll keep my unlock and be able to use the 3.1 firmware?
rlewis312010 said:
So, if I have the S20+ (US Cellular) and want to try the 3.1 firmware:
1.) Download the firmware
2.) Put your file for it into user data field in Odin
3.) Put in AP, CSC (home or whatever to not overwrite my USC one I think) and the rest EXCEPT for the bootloader into Odin
4.) Flash as usual and then everything should work. I'll keep my unlock and be able to use the 3.1 firmware?
Click to expand...
Click to collapse
I did it that way, used the BL included file and flashed all the stock files, after the full wipe everything that I needed was included. Worked great, on UI 3.1 rn
It worked for me also, thanks for making this.
hi jrkruse i just got an A71 5g unlocked (thanks afaneh92), and i was wondering if you could make an aio userdata file for it? so i can flash ui 3.1 firmware to it? like this for my s20 ultra..(this thread)
Related
I have downloaded my Rom from samfirmware, I checked the file and as usual there are PDA,Modem,CSC files in addition to that there is a bootloader file which Im not sure how to use it in odin 1.85, shall I put it in bootloader section? and if so shall I activate the "phone bootloader update" on left side of odin?
thanks
Unless you own an I/O edition of tab, I don't recommend bootloader file. As the bootloader file besides locking the bootloader (if repartition selected in odin) replaces fastboot with recovery in boot screen (keys combo). Hence be careful in flashing bootloader!
Place bootloader in bootloader, tick auto-reboot and Reset time only, and flash. The samfirmware roms for p7510 have been uploaded in development section by me to motivate discussions related to issues. If flashing a touchwiz rom, I recommend the arabic rom from development section. Its taken from samfirmware, but as their edition had issues I repacked it hence error free. The touchwiz in this rom is more polished release version!
Thanks for your help , already done after your instructions and successful
I have 3g version of the tablet and used the 4 files
PDA
CSC
Modem
bootloader
repartition and phone bootloader update not activated
and had a successful flashing
by the way the JPKG6 seems to have less problems as I dont see any auto rotation lags and more smooth scrolling in this rom
This thread applies to Huawei Mate 9 Pro only (model LON*, as M9Pro below). For Mate 9 (model MAH*) please go to the corresponding forum.
-----
Disclaimer:
I won't be responsible for bricked phone. Proceed with your own risk, make sure you know what you are doing.
This thread can be seen as a guide if your phone has exactly the same model and build version as mine. Otherwise please consider it as a description of my experiences for unlocking, flashing and rooting the phone.
SUPPORTED DEVICES:
LON-L29
LON-AL00
-----
As a start, this phone is great and I feel that it doesn’t need to be unlocked and rooted for a stable and long lasting daily use. However, unlock and root is almost a religion if you use Android phones
As a piece of info, big thanks to @raimondomartire, there is a thread for unlock, flash TWRP and root in the Mate 9 forum https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976, which is however according to my experience not totally applicable for the M9Pro anymore. There are also several other threads on the Mate 9 forum. Many things can be shared between both phones, but not always. Be careful about what you are doing!
-----
General info and attentions:
- My phone is M9Pro LON-AL00 (All net version from Chinese Mainland); LON-L29 (International version) should also work.
- This thread applies for build LON-AL00C00B213. Can be also applicable for similar builds, but I couldn’t test. Please report.
- None of the current builds of TWRP (up to 3.1.0) can decrypt data partition by default, which means you could only format the data partition in TWRP in order to access it in recovery (for backup to and install from internal storage etc.). But after formatting, you have to flash Huawei’s special stock data back to data partition (/data/hw_init), otherwise several functions of Huawei ROM won’t work. Refer to this (https://forum.xda-developers.com/showpost.php?p=71302827&postcount=627) or this (https://forum.xda-developers.com/showpost.php?p=72497328&postcount=204). Thanks to @gm007 and @ante0
- There are several root methods which handles encrypted or decrypted data partition. I didn’t format the data partition, i.e. data is still encrypted. If you want to format the data partition, please refer to this thread: https://forum.xda-developers.com/mate-9/how-to/guide-how-to-root-mate-9-decrypt-data-t3569986. Thanks to @eddmecha
- If you need stock ROM, refer to useful links below. Use Huawei Update Extractor to extract the individual partitions from the ROM: https://forum.xda-developers.com/showthread.php?t=2433454
-----
Unlock bootloader:
There is enough info in the internet about unlocking M9Pro’s bootloader. Just a few points to mention:
- Generally, you can follow the steps in @raimondomartire thread (https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976). But unlike he describes in his thread, there is no OEM Unlock options in the developer options anymore. Just use ADB to unlock.
- FRP unlock is not required!
- Huawei enables now a 14-day limitation, where you can officially get the bootloader unlock code 14 days after you first activate your Huawei ID on your phone and have logged in using your Huawei ID 14 CONSECUTIVE days.
- To go around this limitation, you can use dc-unlocker to get the bootloader code immediately. Google yourself
-----
Flash TWRP:
- Still, you can follow the steps in @raimondomartire thread (https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976).
- The image from this thread is 3.0.3, which has some bugs built in, especially when flashing SuperSU.
- You could use TWRP 3.1.0-1 from https://forum.xda-developers.com/mate-9/development/recovery-unofficial-twrp-huawei-mate-9-t3515617, but this one seems to have problem to be recognized as ADB device in recovery.
- There is a version 3.0.2 for Mate 9, which seems to have problem mounting USB-OTG.
- If your data partition is encrypted, you can only use ADB sideload or USB-OTG to install anything.
- If you want to do data wipe in TWRP, you have to flash Huawei’s special stock data back to data partition. See above general info and attentions.
-----
Root:
Firstly, thanks to @ante0 for explaining different flags in the root methods: https://forum.xda-developers.com/showpost.php?p=72504501&postcount=210. Some more discussions between us are also around this post.
I also tried several other root tools on the market (mobilego, vroot, YoRoot, OneClickRoot, iRoot etc.), NONE of them works.
As mentioned, there are different root methods around for unlocking M9Pro, depending on if you want to format your data partition. For me, I didn’t format, and SuperSU works for me. And the mate_9_pro_root.zip from @raimondomartire thread didn’t work for me.
I followed the steps below:
1. Get TWRP 3.1.0-1 (https://forum.xda-developers.com/mate-9/development/recovery-unofficial-twrp-huawei-mate-9-t3515617)
2. Disable fingerprint ID (I think it’s probably optional, but have read somewhere that fingerprint stops working after flashing root).
3. Flash stock boot image for B213D (in download section). I think it’s optional too, but if you have tried other methods before, you can do this step to make sure your boot is stock and clean
4. Flash TWRP 3.1.0-1
5. Flash SuperSU-v2.79-MATE9-init.d_support_no_decrypt-signed.zip (in download section) via USB-OTG (in TWRP the device is not recognized as an ADB device, hence no “ADB sideload”). Thanks to @ante0 for building this zip!
6. Reboot – phone will reboot itself twice and SuperSU.apk will be installed automatically
7. You could flash back to 3.0.3, if you want the ADB sideload function.
-----
Download:
- TWRP 3.0.3-1: https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976
- TWRP 3.1.0-1: https://forum.xda-developers.com/mate-9/development/recovery-unofficial-twrp-huawei-mate-9-t3515617
- SuperSU modified for M9Pro (thanks to @ante0): https://mega.nz/#!bR8D2Bab!bIgMLVmoll9R0GFqoFgkLxULrXlQ2710INt3TNbuI0c
- Boot image from B213D: https://mega.nz/#!LFlGTTZY!AaFq-_quM44YlK_Qdh9PgOjBE3Wtepmyz5OAuo_mabw
-----
Useful links:
- Stock firmware: http://hwmt.ru/oth/HWFF/info/view.php?find_model=lon
- Huawei Update (ROM) Extractor: https://forum.xda-developers.com/showthread.php?t=2433454
Enjoy your Mate!
Just some clarification: (eventhough you wrote it's for AL00C00B213, which I missed xD)
Flashing stock boot is only needed if you're already rooted.
Boot image B213D is only for AL00C00. If you have a different model/build, use the boot image for that specific build:
Download your stock firmware from hwmt.ru and Huawei Update Extractor. Extract update.app from your firmware zip.
Open update.app in Huawei Update Extractor. Rightclick on BOOT and click on Extract selected.
Flash the extracted boot.img using fastboot in download mode (fastboot flash boot boot.img).
OEM Unlocking is required to be enabled. It's just not there in the chinese version (AL00). So check if it's there first and enable if it is.
Hi guys. Not sure if this is the right place to ask but how do I get rid of that annoying "your device is unlocked and can't be trusted....etc " msg?
I have a mate 9 pro and I want to flash twrp and to root it. I did it for some one plus, xiaomi, samsung so I have some experience. reading xda posts about the case of M9pro I understood that is not a simple path and I dont want to hard brick the phone. what precautions should I take?
attached phone config
thank you in advance
ante0 said:
Just some clarification: (eventhough you wrote it's for AL00C00B213, which I missed xD)
Flashing stock boot is only needed if you're already rooted.
Boot image B213D is only for AL00C00. If you have a different model/build, use the boot image for that specific build:
Download your stock firmware from hwmt.ru and Huawei Update Extractor. Extract update.app from your firmware zip.
Open update.app in Huawei Update Extractor. Rightclick on BOOT and click on Extract selected.
Flash the extracted boot.img using fastboot in download mode (fastboot flash boot boot.img).
OEM Unlocking is required to be enabled. It's just not there in the chinese version (AL00). So check if it's there first and enable if it is.
Click to expand...
Click to collapse
hwmt. ru is unavailable
mcn1970 said:
hwmt. ru is unavailable
Click to expand...
Click to collapse
http://hwmt.ru/hwmtsite/firmware-database/
working fine for me.
Edit: I should probably have posted the full link in my previous post. Sorry.
ante0 said:
http://hwmt.ru/hwmtsite/firmware-database/
working fine for me.
Edit: I should probably have posted the full link in my previous post. Sorry.
Click to expand...
Click to collapse
is it all procedures safe? no risk of hard brick?
ante0 said:
Just some clarification: (eventhough you wrote it's for AL00C00B213, which I missed xD)
Flashing stock boot is only needed if you're already rooted.
Boot image B213D is only for AL00C00. If you have a different model/build, use the boot image for that specific build:
Download your stock firmware from hwmt.ru and Huawei Update Extractor. Extract update.app from your firmware zip.
Open update.app in Huawei Update Extractor. Rightclick on BOOT and click on Extract selected.
Flash the extracted boot.img using fastboot in download mode (fastboot flash boot boot.img).
OEM Unlocking is required to be enabled. It's just not there in the chinese version (AL00). So check if it's there first and enable if it is.
Click to expand...
Click to collapse
i unlocked the bootloader and flashed recovery but my OTG stick is not recognized and cannot be mounted. also while in recovery the phone is not seen on PC.
i tried with both recoveries above.
ADB sideload doesnt work...keeps saying starting ADB sideloading features...in TWRP sdcard content is a bunch of files with weird names...
therefore how can I root the phone?
someone please help me!!
mcn1970 said:
i unlocked the bootloader and flashed recovery but my OTG stick is not recognized and cannot be mounted. also while in recovery the phone is not seen on PC.
i tried with both recoveries above.
ADB sideload doesnt work...keeps saying starting ADB sideloading features...in TWRP sdcard content is a bunch of files with weird names...
therefore how can I root the phone?
someone please help me!!
Click to expand...
Click to collapse
edit: solved it
any OTA after?
hi guys. You may or may not find this interesting. I certainly did. I'll post this in the mate 9 pro forum as well but i just thought i could get some ideas from as many of guys as possible seeying that theres a lot more posts here for mate 9 in general.
I have chinese version mate 9 pro that has been rebranded from AL00 to LON Spcseas and rooted. Build number b228. Anyway i recently saw in FF the new b229 so i downloaded all three files which had longer file names than usuall by the way. In twrp, the only file that was visable was the update.zip. So i renamed the hw and public zip files to what they would usually be named. Wiped data, and flashed all three files. Then reflashed supersu.
This is the interesting bit ( i think ). My imei numbers have changed, before flashing, the first imei number ended in 7 - now it ends with 4, the second imei number ended in 9 and now it ends with 7. Also, i now have a MEID number visable which was not there before and a section called android security patch level. Oddly enough im not getting any issues out of play store, im on play store right now and not a single problem regarding authentication. The build number is the same as well. As far as functionality goes, everything seems to be tip top, in fact everything seems to be working better, even unofficial exposed is working well. Only one thing isn't working properly. In phone manager there was a feature in the battery section that darkens the interface for everything to save power and prolong battery. That doesn't seem to be working anymore. In App - Permissions, the permissions is greyed out and it says no permissions requested.. Any thoughts or explenations guys??
Trying to flash another orginal stock rom
I bought a Mate 9 Pro, China Version (LON-AL00C00) want to install Mate 9 Pro, Asia Version (LON-L29C636) software on it. All explanations about Mate 9 Pro is for models which have SD Card. My Mate 9 Pro with dual sims and not containing a SD Card enrty.
I succesfully unlocked the bootloader, installed TWRP but couldn't flash LON-L29C636 stock software. Because TWRP don't see update.zip file. Not only update.zip, any files I downloaded or copied before. When I put a OGT TWRP suddenly exits and phone restarts.:crying:
As you see I can't flash a zip file and ofcourse superuser zip file to root as well. I'm stuck in this triangle. Please give me a hand guys.
I can't root my phone. Because I can't view and locate any file of my phone. When I plug a ogt cable twrp exits and phone restarts. 6GB-128GB Dual Sim version
---------- Post added at 11:48 AM ---------- Previous post was at 11:47 AM ----------
Seems I am the only one who is looking for something about Mate 9 Pro
CrisperNeO said:
This thread applies to Huawei Mate 9 Pro only (model LON*, as M9Pro below). For Mate 9 (model MAH*) please go to the corresponding forum.
-----
Disclaimer:
I won't be responsible for bricked phone. Proceed with your own risk, make sure you know what you are doing.
This thread can be seen as a guide if your phone has exactly the same model and build version as mine. Otherwise please consider it as a description of my experiences for unlocking, flashing and rooting the phone.
SUPPORTED DEVICES:
LON-L29
LON-AL00
-----
As a start, this phone is great and I feel that it doesn’t need to be unlocked and rooted for a stable and long lasting daily use. However, unlock and root is almost a religion if you use Android phones
As a piece of info, big thanks to @raimondomartire, there is a thread for unlock, flash TWRP and root in the Mate 9 forum https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976, which is however according to my experience not totally applicable for the M9Pro anymore. There are also several other threads on the Mate 9 forum. Many things can be shared between both phones, but not always. Be careful about what you are doing!
-----
General info and attentions:
-My phone is M9Pro LON-AL00 (All net version from Chinese Mainland); LON-L29 (International version) should also work.
-This thread applies for build LON-AL00C00B213. Can be also applicable for similar builds, but I couldn’t test. Please report.
-None of the current builds of TWRP (up to 3.1.0) can decrypt data partition by default, which means you could only format the data partition in TWRP in order to access it in recovery (for backup to and install from internal storage etc.). But after formatting, you have to flash Huawei’s special stock data back to data partition (/data/hw_init), otherwise several functions of Huawei ROM won’t work. Refer to this (https://forum.xda-developers.com/showpost.php?p=71302827&postcount=627) or this (https://forum.xda-developers.com/showpost.php?p=72497328&postcount=204). Thanks to @gm007 and @ante0
-There are several root methods which handles encrypted or decrypted data partition. I didn’t format the data partition, i.e. data is still encrypted. If you want to format the data partition, please refer to this thread: https://forum.xda-developers.com/mate-9/how-to/guide-how-to-root-mate-9-decrypt-data-t3569986. Thanks to @eddmecha
-If you need stock ROM, refer to useful links below. Use Huawei Update Extractor to extract the individual partitions from the ROM: https://forum.xda-developers.com/showthread.php?t=2433454
-----
Unlock bootloader:
There is enough info in the internet about unlocking M9Pro’s bootloader. Just a few points to mention:
-Generally, you can follow the steps in @raimondomartire thread (https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976). But unlike he describes in his thread, there is no OEM Unlock options in the developer options anymore. Just use ADB to unlock.
-FRP unlock is not required!
-Huawei enables now a 14-day limitation, where you can officially get the bootloader unlock code 14 days after you first activate your Huawei ID on your phone and have logged in using your Huawei ID 14 CONSECUTIVE days.
-To go around this limitation, you can use dc-unlocker to get the bootloader code immediately. Google yourself
-----
Flash TWRP:
-Still, you can follow the steps in @raimondomartire thread (https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976).
-The image from this thread is 3.0.3, which has some bugs built in, especially when flashing SuperSU.
-You could use TWRP 3.1.0-1 from https://forum.xda-developers.com/mate-9/development/recovery-unofficial-twrp-huawei-mate-9-t3515617, but this one seems to have problem to be recognized as ADB device in recovery.
-There is a version 3.0.2 for Mate 9, which seems to have problem mounting USB-OTG.
-If your data partition is encrypted, you can only use ADB sideload or USB-OTG to install anything.
-If you want to do data wipe in TWRP, you have to flash Huawei’s special stock data back to data partition. See above general info and attentions.
-----
Root:
Firstly, thanks to @ante0 for explaining different flags in the root methods: https://forum.xda-developers.com/showpost.php?p=72504501&postcount=210. Some more discussions between us are also around this post.
I also tried several other root tools on the market (mobilego, vroot, YoRoot, OneClickRoot, iRoot etc.), NONE of them works.
As mentioned, there are different root methods around for unlocking M9Pro, depending on if you want to format your data partition. For me, I didn’t format, and SuperSU works for me. And the mate_9_pro_root.zip from @raimondomartire thread didn’t work for me.
I followed the steps below:
1.Get TWRP 3.1.0-1 (https://forum.xda-developers.com/mate-9/development/recovery-unofficial-twrp-huawei-mate-9-t3515617)
2.Disable fingerprint ID (I think it’s probably optional, but have read somewhere that fingerprint stops working after flashing root).
3.Flash stock boot image for B213D (in download section). I think it’s optional too, but if you have tried other methods before, you can do this step to make sure your boot is stock and clean
4.Flash TWRP 3.1.0-1
5.Flash SuperSU-v2.79-MATE9-init.d_support_no_decrypt-signed.zip (in download section) via USB-OTG (in TWRP the device is not recognized as an ADB device, hence no “ADB sideload”). Thanks to @ante0 for building this zip!
6.Reboot – phone will reboot itself twice and SuperSU.apk will be installed automatically
7.You could flash back to 3.0.3, if you want the ADB sideload function.
-----
Download:
-TWRP 3.0.3-1: https://forum.xda-developers.com/mate-9/development/recovery-huawei-mate-9-pro-unofficial-t3546976
-TWRP 3.1.0-1: https://forum.xda-developers.com/mate-9/development/recovery-unofficial-twrp-huawei-mate-9-t3515617
-SuperSU modified for M9Pro (thanks to @ante0): https://mega.nz/#!bR8D2Bab!bIgMLVmoll9R0GFqoFgkLxULrXlQ2710INt3TNbuI0c
-Boot image from B213D: https://mega.nz/#!LFlGTTZY!AaFq-_quM44YlK_Qdh9PgOjBE3Wtepmyz5OAuo_mabw
-----
Useful links:
-Stock firmware: http://hwmt.ru/oth/HWFF/info/view.php?find_model=lon
-Huawei Update (ROM) Extractor: https://forum.xda-developers.com/showthread.php?t=2433454
Enjoy your Mate!
Click to expand...
Click to collapse
I unlocked bootloader but couldn't root. Anyway I wanted to rebrand my phone to Asia version. Now I'm done but not successful because there is no Google,frp locked, and version is test one.
I can't install twrp because frp lock don't allow it. Also twrp can't read 128 GB internal memory, so I needed to install from pc.
Is there anyway to resolve and install stock Oreo version to my Mate 9 Pro or do you suggest me to resolve it via paid services?
PRA-LX1 cihazımdan Tapatalk kullanılarak gönderildi
livevalue said:
I unlocked bootloader but couldn't root. Anyway I wanted to rebrand my phone to Asia version. Now I'm done but not successful because there is no Google,frp locked, and version is test one.
I can't install twrp because frp lock don't allow it. Also twrp can't read 128 GB internal memory, so I needed to install from pc.
Is there anyway to resolve and install stock Oreo version to my Mate 9 Pro or do you suggest me to resolve it via paid services?
PRA-LX1 cihazımdan Tapatalk kullanılarak gönderildi
Click to expand...
Click to collapse
I've installed Oreo to Mate 9 Pro. If you have 128GB edition don't try to install anything from internal storage. That's it.
PRA-LX1 cihazımdan Tapatalk kullanılarak gönderildi
Hi guys, for re-branding there are threads in general Mate 9 forum. I didnt do it and am not planning to do it either...
CrisperNeO said:
Hi guys, for re-branding there are threads in general Mate 9 forum. I didnt do it and am not planning to do it either...
Click to expand...
Click to collapse
Rebranding is easy with HWOTA system if you will keep your phone EMUI 5.0 Nougat. And there is no risk if you make everything clearly.
PRA-LX1 cihazımdan Tapatalk kullanılarak gönderildi
never used Huawei before have a couple of questions
1. Is there anyway to get back to full stock with relock bootaloder in case the device need to go to service center?
(assume unlock bootloader with dc-unlocker not huawei id one)
2. From question 1 what do i need to do or backup before root?
thnak you so much!
44alphabeT said:
never used Huawei before have a couple of questions
1. Is there anyway to get back to full stock with relock bootaloder in case the device need to go to service center?
(assume unlock bootloader with dc-unlocker not huawei id one)
2. From question 1 what do i need to do or backup before root?
thnak you so much!
Click to expand...
Click to collapse
Yes you can always flash stock ROM as factory out, if you are not in Oreo.
And you can root it. It's your own protection to have a backup. I suggest you have, anyway it's up to you. You can loose all your data after root.
Hi, yersterday I used TWRP trying to install a newer firmware and I wiped system partition and now it does not boot because it doesn't have an OS. I was on EMUI 8 (636) trying to update the firmware.
Is there any way to flash a firmware via TWRP or Fastboot on EMUI 8 (i know partition names change on Oreo).
Thanks!
Was on stock ROM build 9.0.0.217(C636E2R1P12) before I unlocked bootloader to try out Magisk/ROOT. Things are mostly fine but Google Pay does not work as expected. Overall Magisk turns out not too useful for me, and I really need to use Google Pay. So I am trying to go back to the pre-unlocking condition.
After searching on XDA these are the things I tried but failed:
1. Fastboot flash system img - can flash stock ROM but bootloader remain unlocked and google pay won't work.
2. HWOTA - can patch update zips but update is no longer provided by the writer, tried another version of HWOTA update but did not work.
3. dload method - don't have microSD but tried a thumb drive with USB-C but "system install failed" in dload mode, not sure it's the USB or the update.app, in fact couldn't find a offline update.app with the correct region (C636) for this phone.
So currently still on firmware 9.0.0.217(C636E2R1P12) with unlocked bootloader and Magisk.
Please advise what other things I could try. Thank you!
This Is How Too Convert your US model SM-G973U S10 Into Hong Kong Model SM-G9730 S10
Bootloader Must Be Unlocked Too Do This!!Downloads
USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
Odin3_v3.14.1_3B_PatcheD.zip
1. Download TGY firmware for the SM-G9730 model phone
2, Also Have US firmware downloaded for the SM-G973U
3. Reboot to TWRP or Stock Recovery and wipe data then reboot too download/bootloader mode
4. Load the BL and CP files in odin from the SM-G973U firmware In matching slots in odin
5. Load the AP and Home_CSC files from the SM-G9730 firmware in matching slots in odin
6. Load my USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5 In UserData slot in odin
7. Flash the above firmware in Odin.
8. Phone will reboot too TWRP and install root and necessary files then boot too setup
This Is How Too Convert your US Model SM-G973U S10 Into Canadian Model SM-G973W S10
Bootloader Must Be Unlocked Too Do This!!Downloads
USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
Odin3_v3.14.1_3B_PatcheD.zip
1. Download Canadian firmware for the SM-G973W model phone
2. Reboot to TWRP or Stock Recovery and wipe data then reboot too download/bootloader mode
3. Extract the BEYOND1QLTE_CAN_SINGLE.pit from the CSC_OMC_OYN****.tar.md5 file
4. Load the BL,AP,CP and CSC_OMC_OYN****.tar.md5 files in matching slots in odin
5. Load my USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5 In UserData slot in odin
6, In odin choose the pit tab and load the BEYOND1QLTE_CAN_SINGLE.pit you extracted above
7. Flash the above firmware in Odin.
8. Phone will reboot too TWRP and install root and necessary files then boot too setup
This Is How Too Convert your Canadian Model SM-G973W S10 Into US Model SM-G973U/U1 S10
Bootloader Must Be Unlocked Too Do This!!
Downloads
USERDATA_SLOT_G973U_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
Odin3_v3.14.1_3B_PatcheD.zip
1. Download US firmware for the SM-G973U/U1 model phone
2. Reboot to TWRP or Stock Recovery and wipe data then reboot too download/bootloader mode
3. Extract the BEYOND1QLTE_USA_SINGLE.pitfrom the CSC_OMC_OYN****.tar.md5 file
4. Load the BL,AP,CP and CSC_OMC_OYN****.tar.md5 files in matching slots in odin
5. Load my USERDATA_SLOT_G973U_AIO_TWRP_VBMETA_ANDROID_R.tar.md5 In UserData slot in odin
6, In odin choose the pit tab and load the BEYOND1QLTE_CAN_SINGLE.pit you extracted above
7. Flash the above firmware in Odin.
8. Phone will reboot too TWRP and install root and necessary files then boot too setup
This Is How Too Convert your Hong Kong Model SM-G9730 S10 Into US Model SM-G973U/U1 S10
Bootloader Must Be Unlocked Too Do This!! Downloads
G9730ZHU4EUA8_G9730TGY4EUA8_USA.7z
USERDATA_SLOT_G973U_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
Odin3_v3.14.1_3B_PatcheD.zip
Directions
This has not been tested as I do not have the SM-G9730 model phone so let me know
1, Extract G9730ZHU4EUA8_G9730TGY4EUA8_USA.7z
2. Reboot phone too TWRP or stock recovery and wipe data then reboot too download/bootloader
3. Load files in appropriate slots in odin along with USERDATA_SLOT_G973U_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
In UserData slot and flash with odin.
4. Phone will reboot too twrp and process files will reboot back to TWRP once during install then will boot too setup
5, After setup phone may tell you to reboot too install new sim.
jrkruse said:
This Is How Too Convert your US model SM-G973U S10 Into Hong Kong Model SM-G9730 S10
Bootloader Must Be Unlocked Too Do This!!Downloads
USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
Odin3_v3.14.1_3B_PatcheD.zip
1. Download TGY firmware for the SM-G9730 model phone
2, Also Have US firmware downloaded for the SM-G973U
3. Reboot to TWRP or Stock Recovery and wipe data then reboot too download/bootloader mode
4. Load the BL and CP files in odin from the SM-G973U firmware In matching slots in odin
5. Load the AP and Home_CSC files from the SM-G9730 firmware in matching slots in odin
6. Load my USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5 In UserData slot in odin
7. Flash the above firmware in Odin.
8. Phone will reboot too TWRP and install root and necessary files then boot too setup
Click to expand...
Click to collapse
I could not do it from G973U1 to G9730 the cell phone does not allow it
alexmen123 said:
I could not do it from G973U1 to G9730 the cell phone does not allow it
Click to expand...
Click to collapse
what firmware did you try it has to be tgy
Simply a silly question from me: Can we actually unlock the bootloader of the USA Galaxy S10?
From all I know is we can only unlock bootloader for the Exynos Version. Thanks and Huge love if you guys can show me the link or anything else to make my USA S10 free.
Thank you!
robocopvn said:
Simply a silly question from me: Can we actually unlock the bootloader of the USA Galaxy S10?
From all I know is we can only unlock bootloader for the Exynos Version. Thanks and Huge love if you guys can show me the link or anything else to make my USA S10 free.
Thank you!
Click to expand...
Click to collapse
Post 2 has info
[SM_G973U/U1/W_Snapdragon]-[Upgrade Easily Android 11 To 12 Using Odin]-[Automatically Root Remove Forceencrypt Patch Bluetooth And Fix Safetynet]
Must Have An Unlocked Bootloader To Do This! This An odin tar file I have created to flash along with stock odin firmware to automatically install TWRP recovery along with Disable VBMETA image. The tar file will also automatically install magisk...
forum.xda-developers.com
alexmen123 said:
I could not do it from G973U1 to G9730 the cell phone does not allow it
Click to expand...
Click to collapse
also were you trying this with a phone with unlocked bootloader? The bootloader on your SM-G973U1 must be unlocked
jrkruse said:
Were you also trying this with an unlocked bootloader phone? The bootloader of your SM-G973U1 must be unlocked
Click to expand...
Click to collapse
si esta desbloqueado. ¿Qué puedo hacer?
si Pongo firmware tyg en mi g973u1 . Activará segunda sim?
Translation:
if it is unlocked. What I can do?
if I put tyg firmware on my g973u1. Will it activate second sim?
[QUOTE = "jrkruse, publicación: 84541509, miembro: 1949695"]
¿Qué firmware probaste? Tiene que ser tgy
[/CITA]
really my interest is to convert my G973U1 into a dual SIM terminal. Is this possible by switching to the tgy firmware?
alexmen123 said:
[QUOTE = "jrkruse, publicación: 84541509, miembro: 1949695"]
¿Qué firmware probaste? Tiene que ser tgy
[/CITA]
really my interest is to convert my G973U1 into a dual SIM terminal. Is this possible by switching to the tgy firmware?
Click to expand...
Click to collapse
you cannot convert the US phones to dual sim because they dont have 2 seperate imei numbers
I mean they do but one is tied directly to the esim not a physical sim
jrkruse said:
This Is How Too Convert your US Model SM-G973U S10 Into Canadian Model SM-G973W S10
Bootloader Must Be Unlocked Too Do This!!Downloads
USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5
Odin3_v3.14.1_3B_PatcheD.zip
1. Download Canadian firmware for the SM-G973W model phone
2. Reboot to TWRP or Stock Recovery and wipe data then reboot too download/bootloader mode
3. Extract the BEYOND1QLTE_CAN_SINGLE.pit from the CSC_OMC_OYN****.tar.md5 file
4. Load the BL,AP,CP and CSC_OMC_OYN****.tar.md5 files in matching slots in odin
5. Load my USERDATA_SLOT_G973W_AIO_TWRP_VBMETA_ANDROID_R.tar.md5 In UserData slot in odin
6, In odin choose the pit tab and load the BEYOND1QLTE_CAN_SINGLE.pit you extracted above
7. Flash the above firmware in Odin.
8. Phone will reboot too TWRP and install root and necessary files then boot too setup
Click to expand...
Click to collapse
Hi, where can I find the file BEYOND1QLTE_CAN_SINGLE.pit. Looking forward to your help. Thanks a lot
Tuan Anh1 said:
Hi, where can I find the file BEYOND1QLTE_CAN_SINGLE.pit. Looking forward to your help. Thanks a lot
Click to expand...
Click to collapse
Read direction number 3
jrkruse said:
Đọc hướng số 3
Click to expand...
Click to collapse
thanks can i ask is there any way to fix the startup warning
Note: This process is shown for OnePlus Nord 2 and work for any MTK device just replace files as per your model you need to Serch for that)
Credits @Raygen @TheWing
After relocking bootloader you can do safety net pass check to confirm by using following app:
https://play.google.com/store/apps/details?id=org.freeandroidtools.safetynettes
Download Re LiveDVD mtk. Client ( this is ready mtk client ubuntu os no need to Install python, drivers ready to go iso)
re_livedvdV3.iso
drive.google.com
Download Rufus for windows 32/64bit)
https://github.com/pbatard/rufus/releases/download/v3.17/rufus-3.17.exe
Note:Relocking has been done on OOS 11.1 v13 so stock boot img of v13, vbmeta from update zip of v13 is required, recovery must be given below.
Your need to replace files as per oxygen os version you are using.
FOLLOWING are images of DN2101 A13 OOS UPDATE IMAGES EXCEPT RECOVERY IMAGE IT WILL WORK IN ANY PHONE, U NEED YOUR AS PER YOUR REGION I WILL UPDATE THREAD AFTER COLLECTING ALL HERE
Boot img (This is stock A13 indian, other regions must use there current OOS version boot img)( other mtk devices must use there boot img here)
https://forum.xda-developers.com/attachments/boot-img.5460945/
Stock recovery(in zip unzip it you will get img file this will work for any region)( other mtk devices must use there recovery img here)
https://forum.xda-developers.com/attachments/recovery_stock-zip.5464685/
Vbmeta:must have correct vbmeta of current OOS Rom. Version (from stock A13 indian update.zip if U r using EU, OR GLOBAL region NORD replace it with the current OOS version you are for which you want to relock)(other mtk devices must use there vbmeta img here)
vbmeta.img
drive.google.com
All files for EU DN2103 ON A12 UPDTAE :
EU varient v12 files:
Boot. Img:
https://forum.xda-developers.com/attachments/boot_stock_a12-img.5461083/
Vbmeta. Img/
vbmeta.img
drive.google.com
Recovery same link for all)
recovery_stock.zip
drive.google.com
Terminal emulator commands :
1) BOOT TO FASTBOOT connect phone to pc in on condition)
adb reboot fastboot
2)to relock bootloader in terminal emulator connect phone to pc in fastboot mode and type)
fastboot flashing lock
MTK client commands:
1)Flash boot img:
python mtk w boot boot.img
2) Flash recovery img:
python mtk w recovery recovery.img
3) Flash Vbmeta :
python mtk w vbmeta vbmeta.img
wifi is not working. everything working after relock bootloader but wifi is not working
farhansaeeddnp3021 said:
wifi is not working. everything working after relock bootloader but wifi is not working
Click to expand...
Click to collapse
Factory reset u r phone and reboot see
pankspoo said:
Factory reset u r phone and reboot see
Click to expand...
Click to collapse
i did it. but it's not working
farhansaeeddnp3021 said:
i did it. but it's not working
Click to expand...
Click to collapse
Update yourbphone to latest v14
Is there any way to relock the phone just through fastboot? After installing an OTA update, the partitions should match the vbmeta partition, right? So could just relock the bootloader using fastboot flashing lock or would the phone not start then?
NetSoerfer said:
Is there any way to relock the phone just through fastboot? After installing an OTA update, the partitions should match the vbmeta partition, right? So could just relock the bootloader using fastboot flashing lock or would the phone not start then?
Click to expand...
Click to collapse
Your device will go in to boot img corrupt after that.......
PLEASE NOTE: This isnt working if you are on a custom rom! My Bootloader ist broken and locked and I have to figure out how to fix this ****.
Hello Pankspoo.
I reset my Nord 2 again with an A11 image.
Now I wanted to lock the bootloader again. I have implemented your instructions one to one.
After that, the Nord 2 will boot normally and start.
But in the developer options I can still unlock the bootloader. So the option is not greyed out. The OTA cannot be installed but does not lead to a bootloop either.
I used the appropriate boot.img recovery & vbmeta.img.
Do you have any idea?
Best regards
7tyjupiter said:
Hello Pankspoo.
I reset my Nord 2 again with an A11 image.
Now I wanted to lock the bootloader again. I have implemented your instructions one to one.
After that, the Nord 2 will boot normally and start.
But in the developer options I can still unlock the bootloader. So the option is not greyed out. The OTA cannot be installed but does not lead to a bootloop either.
I used the appropriate boot.img recovery & vbmeta.img.
Do you have any idea?
Best regards
Click to expand...
Click to collapse
Check YASNAC app from play store if it's showing safety net check passed your locked.
While installation of OTA what's errors u r getting.
After locking OEM unlock not grates off actually now it's available to unlock again with switchable tab
Sorry for crossposting a lot today, but I am really stuck and it seems that this may be the tool I need. I am on A15, cannot lock bootloader and cannot update.
So, to be sure, for this to work I need the boot.img, recovery.img and vbmeta.img for A15 stock rom? If yes, where can I get those files?
I found the files! Thank you for this guide! It worked perfectly. I really thought my phone was completely bricked. Coming from a Pixel, the root/restore process on this thing is a complete nightmare!!
https://forum.xda-developers.com/attachments/boot-img.5460945/
this link says like this
Oops! We broke the matrix. Someone call Neo!You do not have permission to view this page or perform this action.
Ok. So I think if f-ed up big time! only message I get now is a big red "!" and: "the current image have been destroyed please flash te correct image....
HELP!
Hi, I have a question. I have an unlocked bootloader, if I have my mobile service serviced and I have the original rom reinstalled there will the botloader be locked?
lachatol said:
Hi, I have a question. I have an unlocked bootloader, if I have my mobile service serviced and I have the original rom reinstalled there will the botloader be locked?
Click to expand...
Click to collapse
Definitely, no doubt about that. But the rooting-proces after that is easy and well described here. Don't forget to FIRST take you OTA's, that makes things easier!
exis_tenz said:
Definitely, no doubt about that. But the rooting-proces after that is easy and well described here. Don't forget to FIRST take you OTA's, that makes things easier!
Click to expand...
Click to collapse
I want to lock the botloader, I don't want root anymore. I just need to be sure that if I service the phone for reinstallation to the original firmware, then the bootloader will be locked. Will be? thank you for answer
No worries, it'll be locked after a factory flash!
farhansaeeddnp3021 said:
wifi is not working. everything working after relock bootloader but wifi is not working
Click to expand...
Click to collapse
This happened to me. It turns out that I had version A10 and flashed the A12stock_boot.img and when rebooting I had no wifi. I had no twrp either, since I had just flashed the stock recovery too.
So, I figured "did this actually updated to A12?" I checked the build version on the settings and no, it did not. So maybe thats the reason the system gets confused and some functions (I only noticed wifi) don't work properly.
Anyway, this is how I solved it:
1) restored my A10 version (flashing the file I got from a link on this post)
2) rebooting to A10, I did have wifi. I tried to update to A19 through Software Updater, but even though it did download the update.zip, it failed to update ("didn't pass the verification"). So, I:
3) flashed TWRP again, rebooted into it and installed the update.zip file (in data/ota_package/) that had just been downloaded by Software Updater.
4) Rebooted.
5) Fastboot flashing lock
6) Rebooted again. Congrats, its a brand new phone!!
P.S. Don't forget to lock the OEM unlocking option in Settings.
extranoob said:
This happened to me. It turns out that I had version A10 and flashed the A12stock_boot.img and when rebooting I had no wifi. I had no twrp either, since I had just flashed the stock recovery too.
So, I figured "did this actually updated to A12?" I checked the build version on the settings and no, it did not. So maybe thats the reason the system gets confused and some functions (I only noticed wifi) don't work properly.
Anyway, this is how I solved it:
1) restored my A10 version (flashing the file I got from a link on this post)
2) rebooting to A10, I did have wifi. I tried to update to A19 through Software Updater, but even though it did download the update.zip, it failed to update ("didn't pass the verification"). So, I:
3) flashed TWRP again, rebooted into it and installed the update.zip file (in data/ota_package/) that had just been downloaded by Software Updater.
4) Rebooted.
5) Fastboot flashing lock
6) Rebooted again. Congrats, its a brand new phone!!
P.S. Don't forget to lock the OEM unlocking option in Settings.
Click to expand...
Click to collapse
If u gets wifi issue just flash boot image of OOS version u r using via fastboot