Related
I was trying to relock my phone and after the rsd flash all it does it bootloop....suggestions
AJC9000 said:
I was trying to relock my phone and after the rsd flash all it does it bootloop....suggestions
Click to expand...
Click to collapse
Which ROM were you coming from? I might try flashing 154_5 to relock.
CM7. I tried using the RSD 5 I think then used 5.5 RSD 5.5 kept failing...
AJC9000 said:
CM7. I tried using the RSD 5 I think then used 5.5 RSD 5.5 kept failing...
Click to expand...
Click to collapse
You could try the new version...or factory reset/wipe and then try re-flashing, might want to back up apps in Ti.
I had a similar issue when I sbfed. I got to to boot by first booting in "BP HW Diag & Boot AP" mode(Which did take a few minutes). After that every time I restarted the phone came on fine normally.
All else fails I try the
KTT16 said:
Which ROM were you coming from? I might try flashing 154_5 to relock.
Click to expand...
Click to collapse
Yea the new version was the one that failed on final step. I got it now, android recovery was not booting properly
thanks bubb
Ahhh why are you relocking BTW?
KTT16 said:
Ahhh why are you relocking BTW?
Click to expand...
Click to collapse
4G man I miss it my internet connection is only 3 megs but 4G is faster
I'm at work most of the time and 3G service sucks there
It was a tough decision to make leaving CM7
AJC9000 said:
4G man I miss it my internet connection is only 3 megs but 4G is faster
I'm at work most of the time and 3G service sucks there
It was a tough decision to make leaving CM7
Click to expand...
Click to collapse
So I'm taking it you're back to Stock ROM?.....
Just got a MOPHO couple days ago ..but afraid to mess with unlocking and locking
...
Wow...it must have been tough..you could still run skinny4g though...
---------- Post added at 09:58 AM ---------- Previous post was at 09:58 AM ----------
glock20c said:
So I'm taking it you're back to Stock ROM?.....
Just got a MOPHO couple days ago ..but afraid to mess with unlocking and locking
...
Click to expand...
Click to collapse
Don't be afraid! But once you start, its hard to stop...LOL
Yea I will once the root AIO is back online. I don't have it anymore cleared out my hdd
AJC9000 said:
Yea I will once the root AIO is back online. I don't have it anymore cleared out my hdd
Click to expand...
Click to collapse
One-Click zip
KTT16 said:
One-Click zip
Click to expand...
Click to collapse
beautiful man lol thanks
No problem!
KTT16 said:
Wow...it must have been tough..you could still run skinny4g though...
---------- Post added at 09:58 AM ---------- Previous post was at 09:58 AM ----------
Don't be afraid! But once you start, its hard to stop...LOL
Click to expand...
Click to collapse
True.. Right now im trying the bootstrap method, to install a theme that resembles CM, I use smart keyboard pro to make the text keyboard look stock and player pro gives me stock music player .
This has happened a couple times when trying to flash 198_7 sbf from CM7. I either get into a bootloop or it won't boot at all. RSD status was rebooting device.
I pulled and reinserted the battery, went into Android recovery. At the triangle warning pressed the vol up + vol down at the same time to go into factory recovery. That's where I do a reboot. It states clean reboot, or something like that.
I may be off on a couple of my terms because I'm doing this from memory, but I've done this twice now.
Bricked after sbf on OTA .629?
Now we found the way to unbrick your d2g, the main developer is the guy who found the way to root .629.
Follow the step now
# If your device bricked after flash .29/.33,please flash full .608 sbf at first
1.Download this sbf file and flash in RSDLite
db.tt/WCJQX72O
2. Reboot recovery ,wipe and apply .629 ota update.zip (www.mediafire.com/?591t5kzfmgcm4d5)
NOTE: Step 2. is VERY important, when you finished flash sbf in step 1. ,your device working on a UNSTABLE .608 & .629 hybrid rom
Now your device work
BTW. If you have any problem when using OTA .629 and want reset your phone, just flash full .608 sbf to brick your phone and unbrick again
Sent from my DROID2 GLOBAL using xda premium
zyy757 said:
Bricked after sbf on .629?
Now we found the way to unbrick your d2g, the main developer is the guy who found the way to root .629.
Follow the step now
# If your device bricked after flash .29/.33,please flash full .608 sbf at first
1.Download this sbf file and flash in RSDLite
http://db.tt/EVi6YJPy
2. Reboot recovery and apply .629 ota update.zip
Now your device work
Sent from my DROID2 GLOBAL using xda premium
Click to expand...
Click to collapse
the link is broke and i try before with sbf 608 and keep on the same screen message "bootloader"....
fulvi0 said:
the link is broke and i try before with sbf 608 and keep on the same screen message "bootloader"....
Click to expand...
Click to collapse
Sorry, the url has updated
Sent from my DROID2 GLOBAL using xda premium
thx
zyy757 said:
Sorry, the url has updated
Sent from my DROID2 GLOBAL using xda premium
Click to expand...
Click to collapse
don't worry thank you, i'm already did, and my phone is working, thank you very much.
My pleasure
thanks man , it worked for me, i unbreaked my d2g
thanksssssssssss
unbrick a softbrick
I tried to root my MD2G
and it gave me the following reply
Bootloader
DO.11
Err:A5,70,70,00,1F
MEM_MAP Blank
Service Req'd
Battery low
Cannot program
The last 2 lines keep flashing.
I try to charge the battery to no avail.
this has been going on for 2 days.
Please could some one help me out
I do not know what to do.
maceugene said:
I tried to root my MD2G
and it gave me the following reply
Bootloader
DO.11
Err:A5,70,70,00,1F
MEM_MAP Blank
Service Req'd
Battery low
Cannot program
The last 2 lines keep flashing.
I try to charge the battery to no avail.
this has been going on for 2 days.
Please could some one help me out
I do not know what to do.
Click to expand...
Click to collapse
Charge, or change another battery
Sent from my DROID2 GLOBAL using xda premium
buy a $5 spare battery charger from ebay or amazon
http://www.amazon.com/gp/product/B0...&pf_rd_t=101&pf_rd_p=470938631&pf_rd_i=507846
thanks alot.just bought one. will take about 11 days to get to me. after done all will keep you informed.thanks
Always Bootloader
My D2G always goes into Bootloader whatever i do adn shows
"Bootloader
D0.11"
I flashed it with VRZ_A956_4.5.608_1FF_01.sbf then BL=2 BOOT REC CDT.sbf but again the same problem. Couple of times phone got started but for only some time, after some time when i reboot the phone it goes into bootloader. i need immediate help guys...
One thing more i have another D2G which got bricked after .629 but when unbrick method was discovered it got fixed with no issues. the reason i am sharing this is that it was going into bootloader straightaway when i press power button BUT this new one shows M logo for some time and then goes into bootloader...
zyy757 said:
Charge, or change another battery
Sent from my DROID2 GLOBAL using xda premium
Click to expand...
Click to collapse
I got the charger and charged the battery.
Flashed as instructed but after it shows the motorola sign.It does not go futher. remains at 100% and nothing more
What do u advice i do?
it just got stuck, reboot phone should be good
edit: sorry, you may need to boot into recovery, and wipe data
Sent from my DROID X2 using xda premium
---------- Post added at 11:47 PM ---------- Previous post was at 11:41 PM ----------
wipe date in
Android Recovery
http://droid.koumakan.jp/wiki/Android_Recovery
did you get it?
Sent from my DROID X2 using xda premium
chetansaraf said:
My D2G always goes into Bootloader whatever i do adn shows
"Bootloader
D0.11"
I flashed it with VRZ_A956_4.5.608_1FF_01.sbf then BL=2 BOOT REC CDT.sbf but again the same problem. Couple of times phone got started but for only some time, after some time when i reboot the phone it goes into bootloader. i need immediate help guys...
One thing more i have another D2G which got bricked after .629 but when unbrick method was discovered it got fixed with no issues. the reason i am sharing this is that it was going into bootloader straightaway when i press power button BUT this new one shows M logo for some time and then goes into bootloader...
Click to expand...
Click to collapse
Plz somebody help me out on this
Downgrade .629
Hello,
I have updated the phone to .629 however I would like downgrade to .608
Is there method for this?
Thanks
no, once on 629, that's it, any other sbf will brick phone
---------- Post added at 11:19 PM ---------- Previous post was at 11:14 PM ----------
you can use ezSBF & Root 2.3.4/ 4.5.629 to root if that's what you want
:crying:
What are the problems with this version?
depends on what you mean, by problems?
it can be rooted, bootstrapped, and flash roms
what else do you want?
I thought there were more.
Thanks
ok,
So like an idiot, i began the S-OFF process without reverting my SuperCID. I cannot get past step 8, and i am having errors flashing my RUU.
Right now i cannot get past the bootloader. If i try to fastboot reboot, it takes me back to the bootloader. If i try a reboot, it takes me back to the bootloader.
Is there something that i can flash to get me back and running? I have tried numerous things, and i really need my phone back tonight. Grandfather is in the hospital, and i have no way to contact anyone except through facebook / email.
does anyone have some ideas, or know what i need to do? I honestly dont care about root or s-off, i can do that later. Right now i just need a bootable phone.
help!
squeezyb said:
ok,
So like an idiot, i began the S-OFF process without reverting my SuperCID. I cannot get past step 8, and i am having errors flashing my RUU.
Right now i cannot get past the bootloader. If i try to fastboot reboot, it takes me back to the bootloader. If i try a reboot, it takes me back to the bootloader.
Is there something that i can flash to get me back and running? I have tried numerous things, and i really need my phone back tonight. Grandfather is in the hospital, and i have no way to contact anyone except through facebook / email.
does anyone have some ideas, or know what i need to do? I honestly dont care about root or s-off, i can do that later. Right now i just need a bootable phone.
help!
Click to expand...
Click to collapse
Did you relock the boot loader?
Sent from my DROID RAZR using Tapatalk 2
yes i did
squeezyb said:
yes i did
Click to expand...
Click to collapse
More info would help like what errors you are getting
Sent from my DROID RAZR using Tapatalk 2
adb wont even find my device, so i am not getting any errors. is there a working RUU i can rename to PJ53IMG, and flash that through the bootloader?
http://forum.xda-developers.com/showthread.php?p=28723878
Sent from my DROID RAZR using Tapatalk 2
right, i tried this and had no success. the bootloader went through the process, and began to load the file, but did not finish the process. Could i possibly have tried flashing the wrong one?
i know this is something simple that i can flash, but it is not working
squeezyb said:
right, i tried this and had no success. the bootloader went through the process, and began to load the file, but did not finish the process. Could i possibly have tried flashing the wrong one?
Click to expand...
Click to collapse
Either should work but try the other
Sent from my DROID RAZR using Tapatalk 2
i tried using the one from unlimited.io, renaming it to PJ53IMG, but it would not flash... in theory that would do the trick right?
i am trying to download the file again, we'll see if that works. possibly corrupted on my end
squeezyb said:
i tried using the one from unlimited.io, renaming it to PJ53IMG, but it would not flash... in theory that would do the trick right?
i am trying to download the file again, we'll see if that works. possibly corrupt
Click to expand...
Click to collapse
Probably not. Use the one provided in Andy's thread. ADB is probably not working because debugging has been turned off.
Have you tried the recovery? Check to see if that works. If not try to fastboot a recovery. The command is "Fastboot flash recovery". Try with TWRP. If that takes then try to flash a ROM with that.
blazingwolf said:
Probably not. Use the one provided in Andy's thread. ADB is probably not working because debugging has been turned off.
Click to expand...
Click to collapse
the link in andy's thread is busted, or i would. unless i am wrong.. have you tried it?
On my side ill say do what the ther said, if you still have supercid you can unlock device and flash recovery and flash a working rom if you want it booteable
Sent from my ASUS Transformer Pad TF300T using xda app-developers app
squeezyb said:
the link in andy's thread is busted, or i would. unless i am wrong.. have you tried it?
Click to expand...
Click to collapse
Yep. Working just fine for me.
Anyways, try the recovery route. I think it is your best bet.
blazingwolf said:
Yep. Working just fine for me.
Anyways, try the recovery route. I think it is your best bet.
Click to expand...
Click to collapse
OK FALSE ALARM!
I am back in business.
the first time tried flashing the RUU it did not work. i redownloaded, tried again, and it works fine.
Thank you everyone for dealing with my noob behavior.
<3 you all
squeezyb said:
OK FALSE ALARM!
I am back in business.
the first time tried flashing the RUU it did not work. i redownloaded, tried again, and it works fine.
Thank you everyone for dealing with my noob behavior.
<3 you all
Click to expand...
Click to collapse
Great to hear.
squeezyb said:
OK FALSE ALARM!
I am back in business.
the first time tried flashing the RUU it did not work. i redownloaded, tried again, and it works fine.
Thank you everyone for dealing with my noob behavior.
<3 you all
Click to expand...
Click to collapse
Everyone panics a little bit when the screen goes black
Sent from my DROID RAZR using Tapatalk 2
jamminjon82 said:
Everyone panics a little bit when the screen goes black
Sent from my DROID RAZR using Tapatalk 2
Click to expand...
Click to collapse
No truer words are spoken
jamminjon82 said:
Everyone panics a little bit when the screen goes black
Sent from my DROID RAZR using Tapatalk 2
Click to expand...
Click to collapse
Yep. And somehow time stands still for an eternity until something happens to let you know its alive.
I'll ask here first I achieved s off bit it destroyed my sd well to cut it short I flashed the ruu.zip I'm now s off with a locked bootloader no superuser or root and no recovery how do I install a recovery?
Sent from my ADR6410LVW using xda app-developers app
prairiedogn said:
I'll ask here first I achieved s off bit it destroyed my sd well to cut it short I flashed the ruu.zip I'm now s off with a locked bootloader no superuser or root and no recovery how do I install a recovery?
Sent from my ADR6410LVW using xda app-developers app
Click to expand...
Click to collapse
look here: http://forum.xda-developers.com/showthread.php?t=1435228
Long story short (to avoid me from pulling my hair out of my head.) I have an HTC Thunderbolt which I rooted and installed a custom rom on (using the Revolutionary boot loader). It had an issue where it regularly wouldn't start up into the original rom OS and keep restarting at the HTC logo screen. After I installed the custom rom it was ok for a while but then permanently got stuck with the issue of not starting up into the rom OS and keeps restarting at the HTC logo screen.
Verizon sent me a replacement phone (outside of my warranty - for free - which they rarely do), but I need to send the old phone back. I was able to use the new phone they sent and my old SD card to get the original rom files onto it and then install the original rom via the Revolutionary boot loader but I can't get the original boot loader to install and replace the Revolutionary boot loader now. I tried lots of guides, and finally tried this guide again: http://forum.xda-developers.com/showthread.php?t=1310014&highlight=stock+ruu
I don't think I can use that guide though because it sounds like you need to be able to boot into the rom OS first for the tbolt tool to recognize the phone. I can't boot into the rom OS, I can only access the boot loader screen (which is currently Revolutionary.)
Anyone have any idea how I can load the original boot loader?
(I would have posted this as a reply to the thread I linked above, but my account is newish and doesn't have enough posts for my account to be allowed to post there. And I have til Wednesday - January 23, to send back the old phone to Verizon so they don't charge me for the replacement phone.) Any help is greatly appreciated.
Reroot it if you can and use the allinone tool to unroot.
Sent from my ADR6400L using Tapatalk 2
Watch this video. This will walk you through it.
https://www.youtube.com/watch?v=Ug5pEv9y5r0&feature=youtube_gdata_player
Sent from my ADR6400L using xda premium
RBarnett09 said:
Watch this video. This will walk you through it.
//**YouTube URL**//
Sent from my ADR6400L using xda premium
Click to expand...
Click to collapse
Hi,
I'm trying to follow this video guide you sent me, but it appears I need to be able to start my phone into the OS. My phone does not start into the OS, and the only thing I can get it to start into is the boot loader screen (otherwise it just keeps restarting at the HTC logo screen.)
Is there a way I can uninstall "Revolutionary" and reinstall the original boot loader when I only have access to the boot loader screen?
Thanks.
disconnecktie said:
Reroot it if you can and use the allinone tool to unroot.
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
Why aren't you trying THIS ^^^^^^^ as suggested? :good:
santod040 said:
Why aren't you trying THIS ^^^^^^^ as suggested? :good:
Click to expand...
Click to collapse
Because I can't start my phone into the Android OS, therefor I can't reroot it as far as I know, and I don't think I can use the All-In-One Tool. Can I? Is there a way around the issue I'm having where my phone only can start into the boot loader menu?
jshine1337 said:
Because I can't start my phone into the Android OS, therefor I can't reroot it as far as I know, and I don't think I can use the All-In-One Tool. Can I? Is there a way around the issue I'm having where my phone only can start into the boot loader menu?
Click to expand...
Click to collapse
Go to post #7 on THIS PAGE and grab the files specified and follow the steps.
Good luck
santod040 said:
Go to post #7 on THIS PAGE and grab the files specified and follow the steps.
Good luck
Click to expand...
Click to collapse
Yes, this seems prospective. I have some high hopes right now and am going to try to do this right now. I just have to let my battery charge a little first because it seems that it's too low to let it try to install. Unfortunately my HTC logo screen restart problem is also coupled with some weird issue where it keeps trying to turn on while its charging, so it takes a long time (if it's even charging?) to charge.
If this works, I will be so grateful for your response.
:fingers-crossed:
jshine1337 said:
Yes, this seems prospective. I have some high hopes right now and am going to try to do this right now. I just have to let my battery charge a little first because it seems that it's too low to let it try to install. Unfortunately my HTC logo screen restart problem is also coupled with some weird issue where it keeps trying to turn on while its charging, so it takes a long time (if it's even charging?) to charge.
If this works, I will be so grateful for your response.
:fingers-crossed:
Click to expand...
Click to collapse
It worked! I was able to get rid of Revolutionary, and install the original hboot bootloader. Yay!
/*Now one last question, and I may be mistaken, but shouldn't the top of the boot loader screen say "LOCKED" or something in similar in pink? If so, how do I reset it to say that? I want to make the phone look as genuinely unrooted as possible. */ NEVERMIND, it all worked out.
I just wonder if I missed anything and they'll still be able to tell I rooted it at one point? I loaded the original Android OS rom, and followed post 7 off that guide to restore the original hboot bootloader. Do I need to do something specifically to reset S-OFF? Or will it already be reset?
Thank you.
I think you have to be unlocked to put s on. Then lock it afterwards. Kind of reverse the process.
Sent from my ADR6400L using Tapatalk 2
---------- Post added at 06:02 PM ---------- Previous post was at 05:51 PM ----------
disconnecktie said:
I think you have to be unlocked to put s on. Then lock it afterwards. Kind of reverse the process.
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
Also, I have never unrooted a phone to send it to Verizon or asurion. Just saying...
Sent from my ADR6400L using Tapatalk 2
disconnecktie said:
I think you have to be unlocked to put s on. Then lock it afterwards. Kind of reverse the process.
Sent from my ADR6400L using Tapatalk 2
---------- Post added at 06:02 PM ---------- Previous post was at 05:51 PM ----------
Also, I have never unrooted a phone to send it to Verizon or asurion. Just saying...
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
Ok, so by default S-OFF is set to ON? How do I go about setting it to ON?
I have no idea off the top of my head but I know the allinonetool will revert your phone to completely factory specs. That is why I suggested it in the first place. Going back to s on is no easy task and you need to be very familiar with adb to do it.
Sent from my ADR6400L using Tapatalk 2
disconnecktie said:
I have no idea off the top of my head but I know the allinonetool will revert your phone to completely factory specs. That is why I suggested it in the first place. Going back to s on is no easy task and you need to be very familiar with adb to do it.
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
OoO hmm. Is there a way I can get the All-In-One tool to recognize my phone from the boot loader menu only? (Since it doesn't start up into the Android OS.)
jshine1337 said:
OoO hmm. Is there a way I can get the All-In-One tool to recognize my phone from the boot loader menu only? (Since it doesn't start up into the Android OS.)
Click to expand...
Click to collapse
I dunno but you should try fastboot flashing an Ruu. Unlock and s off again and then run the allinonetool. I know it's a pain but it if you want to be totally stock that is the best way to do it.
Sent from my ADR6400L using Tapatalk 2
disconnecktie said:
I dunno but you should try fastboot flashing an Ruu. Unlock and s off again and then run the allinonetool. I know it's a pain but it if you want to be totally stock that is the best way to do it.
Sent from my ADR6400L using Tapatalk 2
Click to expand...
Click to collapse
Ok. I'm pretty sure I flashed an RUU already? Not 100% positive. Is that what resets the OS rom to the original Android OS rom?
Also, what is the difference between fastboot flashing and just flashing it from the regular boot loader menu?
Sorry to sound newbish.
Thanks.
jshine1337 said:
Hi,
I'm trying to follow this video guide you sent me, but it appears I need to be able to start my phone into the OS. My phone does not start into the OS, and the only thing I can get it to start into is the boot loader screen (otherwise it just keeps restarting at the HTC logo screen.)
Is there a way I can uninstall "Revolutionary" and reinstall the original boot loader when I only have access to the boot loader screen?
Thanks.
Click to expand...
Click to collapse
Oh, gotcha. The only reason why I didn't mention the tool was because when I tried to unroot with it, it wouldn't let me. It basically said another program was running and I figured you were experiencing the same issue.
Glad it worked. Disconnecktie is a very reliable source for this device.
Sent from my ADR6400L using xda premium
So I have never had this problem before I have a 76920d I have unlocked boot loader and I flashed cm10.1 I went through all the steps on fixing the wonky touch screen and stuff everything was running good for about a week then the other day I booted into recovery and I set the phone down for a minute to do something and my phone was split into two screens of the same image I've tried flashing kdz no fix and I tried restoring a previous back up didn't work now I have no idea what to do. This is a back up phone so I still have a phone to use but it's a 200 dollar phone and would like fixed thank you
Sent from my LG-P769 using xda premium
mderuelle said:
So I have never had this problem before I have a 76920d I have unlocked boot loader and I flashed cm10.1 I went through all the steps on fixing the wonky touch screen and stuff everything was running good for about a week then the other day I booted into recovery and I set the phone down for a minute to do something and my phone was split into two screens of the same image I've tried flashing kdz no fix and I tried restoring a previous back up didn't work now I have no idea what to do. This is a back up phone so I still have a phone to use but it's a 200 dollar phone and would like fixed thank you
Sent from my LG-P769 using xda premium
Click to expand...
Click to collapse
Which rom are you running now?
Did you try flashing stock xloader and uboot ?
No I tried going to the page that tells you how but it said it was down please come back later. Could you post the link to the thread it's in I would appreciate it
Edit: I'm on stock Rom on a 76920d now I restored a backup trying to fix the problem but it didn't work kdz flashing didn't work either
Sent from my LG-P769 using xda premium
mderuelle said:
No I tried going to the page that tells you how but it said it was down please come back later. Could you post the link to the thread it's in I would appreciate it
Edit: I'm on stock Rom on a 76920d now I restored a backup trying to fix the problem but it didn't work kdz flashing didn't work either
Sent from my LG-P769 using xda premium
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=40121966&postcount=7 #1
hopefully it's not hardware-related problem
Lelus said:
http://forum.xda-developers.com/showpost.php?p=40121966&postcount=7 #1
hopefully it's not hardware-related problem
Click to expand...
Click to collapse
so i am having trouble with kdz fflash it hangs on 6 percent ive tried emergency cs emergency and diag theyt all do the same thing im not sure if i did the ufix correctley but it didnt seem like it did anything
mderuelle said:
so i am having trouble with kdz fflash it hangs on 6 percent ive tried emergency cs emergency and diag theyt all do the same thing im not sure if i did the ufix correctley but it didnt seem like it did anything
Click to expand...
Click to collapse
you don't need to flash any kdz.
if lg logo is still mirrored then uxfix did not work. did you run start.bat as an administrator?
Lelus said:
you don't need to flash any kdz.
if lg logo is still mirrored then uxfix did not work. did you run start.bat as an administrator?
Click to expand...
Click to collapse
didnt eveb think about doing that it worked thanks for the help i actually sold the working phone and switched carriers i have another one for sale if anyone would like. upgraded to s4 so no need for other device